1、B341-15UN pressure receptacles and multiple-element gas containers for the transport of dangerous goodsLegal Notice for StandardsCanadian Standards Association (operating as “CSA Group”) develops standards through a consensus standards development process approved by the Standards Council of Canada.
2、 This process brings together volunteers representing varied viewpoints and interests to achieve consensus and develop a standard. Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or verify the cont
3、ent of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, i
4、ts merchantability, or its non-infringement of any third partys intellectual property rights. CSA Group does not warrant the accuracy, completeness, or currency of any of the information published in this document. CSA Group makes no representations or warranties regarding this documents compliance
5、with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, IN
6、CLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR PO
7、SSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or on behalf of any person or entity o
8、r to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Group accepts no responsibility whatsoever arising in any way from any and all us
9、e of or reliance on the information contained in this document. CSA Group is a private not-for-profit company that publishes voluntary standards and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with the contents of the standards or other documents it publis
10、hes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in printed or electronic form), CSA Group is the owner, or the authorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise no
11、ted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, or disclosure of this document m
12、ay violate laws that protect CSA Groups and/or others intellectual property and may give rise to a right in CSA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA Group reserves all intellectual property rig
13、hts in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of patent rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determinati
14、on of the validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electro
15、nic form:sLOADTHISDOCUMENTONTOACOMPUTERFORTHESOLEPURPOSEOFREVIEWINGITsSEARCHANDBROWSETHISDOCUMENTANDsPRINTTHISDOCUMENTIFITISIN0$ rather, it was developed to incorporate the ISO standards as referenced in the United Nations Recommendations on the Transport of Dangerous Goods Model Regulations, 18th r
16、ev. ed. (2013) (“UN Model Regulations”) as an optional means of compliance and hence to provide for a broader selection of authorized pressure receptacles and facilitate international transport.In the development of this Standard, the Subcommittee reviewed and made extensive use of the UN Model Regu
17、lations. It should be noted that members of the Subcommittee participated in developing and evaluating the ISO pressure receptacle Standards that are included in the UN Model Regulations. This Standard takes into account proven experience and recent technical advances. The following requirements hav
18、e been included in this Standard for consistency with North American practice:(a) manufacturers, inspection bodies, periodic inspection and test bodies, and design review agencies need to be registered with Transport Canada;(b) UN pressure receptacles and multiple-element gas containers manufactured
19、 in accordance with this Standard are marked with the letters “CAN” to denote the country of approval; and(c) an inspection body is not authorized to delegate its inspection functions to inspectors of the manufacturer.This Standard was prepared by the Subcommittee on UN Pressure Receptacles and Mult
20、iple-Element Gas Containers for the Transport of Dangerous Goods, under the jurisdiction of the Technical Committee on Cylinders, Spheres, and Tubes for the Transportation of Dangerous Goods and the Strategic Steering Committee on Mechanical and Industrial Equipment Safety, and has been formally app
21、roved by the Technical Committee.Notes: (1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.(2) Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Sta
22、ndard to judge its suitability for their particular purpose.(3) This Standard was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessar
23、ily unanimity”. It is consistent with this definition that a member may be included in the Technical Committee list and yet not be in full agreement with all clauses of this Standard.(4) To submit a request for interpretation of this Standard, please send the following information to inquiriescsagro
24、up.org and include “Request for interpretation” in the subject line:(a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch;(b) provide an explanation of circumstances surrounding the actual field condition; and(c) where possible, phras
25、e the request in such a way that a specific “yes” or “no” answer will address the issue.Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are available on the Current Standards Activities page at standardsactivities.csa.ca.(5)
26、This Standard is subject to review five years from the date of publication. Suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquiriescsagroup.org and include “Proposal for change” in the subject
27、line:(a) Standard designation (number);(b) relevant clause, table, and/or figure number;(c) wording of the proposed change; and(d) rationale for the change. 2015 CSA GroupUN pressure receptacles and multiple-element gascontainers for the transport of dangerous goodsSeptember 2015 1B341-15UN pressure
28、 receptacles and multiple-element gas containers for the transport of dangerous goods1Scope1.1This Standard specifies requirements for the design, construction, initial inspection and testing, marking, periodic inspection and testing, and repair of UN pressure receptacles and multiple-element gas co
29、ntainers (MEGCs) for the transport of dangerous goods. Annex A specifies the regulatory requirements for the conformity assessment system and registration requirements for manufacturers and inspection bodies. Annex B specifies the regulatory requirements for the conformity assessment system and regi
30、stration requirements for periodic inspection and test bodies and for repair facilities. Annex C specifies the design approval process for multiple-element gas containers. Tables 1 to 9 provide information on the UN pressure receptacles covered by this Standard.Note: It should be noted that complian
31、ce with the provisions of the Transportation of Dangerous Goods Act and the Regulations thereto may call for additional requirements due to particular characteristics or properties of individual dangerous goods.1.2In this Standard, “shall” is used to express a requirement, i.e., a provision that the
32、 user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard.Notes accompanying clauses do not include re
33、quirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.Notes to tables and figures are considered part of the table or figure and may be written as requirements.Annexes are designated normative (mandatory)
34、or informative (non-mandatory) to define their application.2 Reference publicationsThis Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below, including all amendments published thereto. Where there is an inconsistency between this S
35、tandard and a referenced publication other than the Transportation of Dangerous Goods Act and its regulations, the requirements of this Standard shall prevail. Users of this Standard should avoid directly applying a referenced publication without carefully considering this Standards reference to tha
36、t publication. Note: See Annex E for information on the reference organization.CSA Group B51-14Boiler, pressure vessel, and pressure piping codeB341-15 2015 CSA Group2 September 2015B342-15Selection and use of UN pressure receptacles and multiple-element gas containers for the transport of dangerous
37、 goods, Class 2B625-13Portable tanks for the transport of dangerous goodsCAN/CSA-ISO 9001-08 (R2014)Quality management systems RequirementsASME (American Society of Mechanical Engineers)B31.3-2014Process PipingCGA (Compressed Gas Association)C-1-2009Methods for Pressure Testing Compressed Gas Cylind
38、ersC-6.3-2013Standard for Visual Inspection of Low Pressure Aluminum Alloy Compressed Gas CylindersC-11-2013Practices for Inspection of Compressed Gas Cylinders at Time of Manufacture TB-16-2010Recommended Coding System for Threaded Cylinder Outlets and Threaded Valve InletsGovernment of CanadaTrans
39、portation of Dangerous Goods Act, 1992, SC 1992, c. 34Transportation of Dangerous Goods Regulations (including amendments)IMO (International Maritime Organization) International Convention for Safe Containers (CSC), 1972, as amendedISO (International Organization for Standardization)1496-3:1995Serie
40、s 1 freight containers Specification and testing Part 3: Tank containers for liquids, gases and pressurized dry bulk3807-1:2000Cylinders for acetylene Basic requirements Part 1: Cylinders without fusible plugs3807-2:2000Cylinders for acetylene Basic requirements Part 2: Cylinders with fusible plugs4
41、706:2008 (corrected version)Gas cylinders Refillable welded steel cylinders Test pressure 60 bar and below6406:2005Gas cylinders Seamless steel gas cylinders Periodic inspection and testing7866:2012/Cor. 1:2014Gas cylinders Refillable seamless aluminium alloy gas cylinders Design, construction and t
42、esting 2015 CSA GroupUN pressure receptacles and multiple-element gascontainers for the transport of dangerous goodsSeptember 2015 39809-1:2010Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength le
43、ss than 1 100 MPa9809-2:2010Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa9809-3:2010Gas cylinders Refillable seamless steel gas cylinders Design, constructi
44、on and testing Part 3: Normalized steel cylinders9809-4:2014Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa10460:2005Gas cylinders Welded carbon-steel cylinders Periodic inspection and te
45、sting10461:2005/A1:2006Gas cylinders Seamless aluminium-alloy gas cylinders Periodic inspection and testing10462:2013Gas cylinders Acetylene cylinders Periodic inspection and maintenance10961:2010Gas Cylinders Cylinder bundles Design, manufacture, testing and inspection11114-1:2012Gas cylinders Comp
46、atibility of cylinder and valve materials with gas contents Part 1: Metallic materials11118:1999Gas cylinders Non-refillable metallic gas cylinders Specification and test methods11119-1:2012Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 1: Hoop wrapp
47、ed fibre reinforced composite gas cylinders and tubes up to 450 l11119-2:2012/A1:2014Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners11119-3:
48、2013Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450L with non-load-sharing metallic or non-metallic liners11120:1999Gas cylinders Refillable seamless steel tubes for compres
49、sed gas transport, of water capacity between 150 L and 3000 L Design, construction and testing11513: 2011Gas cylinders Refillable welded steel cylinders containing materials for sub-atmospheric gas packaging (excluding acetylene) Design, construction, testing, use and periodic inspectionB341-15 2015 CS
