CSN 22 2198-1987 Milling cutters Right-hand half-coarse-tooth plain face milling cutters with taper shank and cotter hole《带锥柄及扁销孔的右手半粗齿端铣刀》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

BS EN ISO 8362-3-2003 Injection containers and accessories - Aluminium caps for injection vials《注射液容器及附件 注射小瓶用的铝盖》.pdf

BS EN ISO 8362-4-2011 Injection containers and accessories Injection vials made of moulded glass《注射容器及其附件 模压玻璃所制的注射剂瓶》.pdf

BS EN ISO 8362-5-2016 Injection containers and accessories Freeze drying closures for injection vials《注射容器和附件 注射瓶的冷冻干燥瓶塞》.pdf

BS EN ISO 8362-6-2011 Injection containers and accessories Caps made of aluminium-plastics combinations for injection vials《注射容器及附件 铝塑组合制注射帽盖 》.pdf

BS EN ISO 8362-7-2010 Injection containers and accessories Injection caps made of aluminium-plastics combinations without overlapping plastics part《注射容器及附件 无重叠塑料部件的铝塑组合制成的注射帽盖》.pdf

BS EN ISO 8367-1-1995 Packaging Dimensional tolerances for general purpose sacks Paper sacks《包装 一般用途包装袋的尺寸公差 纸袋》.pdf

BS EN ISO 8367-2-1995 Packaging Dimensional tolerances for general purpose sacks Sacks made from thermoplastic flexible film《包装 一般用途包装袋的尺寸公差 热塑性塑料软薄膜包装袋》.pdf

BS EN ISO 8381-2008 Milk-based infant foods - Determination of fat content - Gravimetric method (Reference method)《奶基幼儿食品 脂肪含量的测定 重量法(参考方法)》.pdf

BS EN ISO 8384-2001 Ships and marine technology Dredgers Vocabulary《船舶和海洋技术 挖泥船 词汇表》.pdf