CSN 25 4020-1973 Screw gauges Limit screw plug gauges Metric screw thread diameter 1 mm to 100 mm《螺纹规 限制螺钉插塞规 公制螺纹 直径 1 mm 到100mm》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

BS 6946-1988 Specification for metal channel cable support systems for electrical installations《电气设备用金属管道电缆支撑系统规范》.pdf

BS 6949-1991 Specification for bitumen-based coatings for cold application excluding use in contact with potable water《与饮用水接触除外的冷用沥青基涂层规范》.pdf

BS 6953-1988 Glossary of terms for procedures for setting out measurement and surveying in building construction (including guidance notes)《建筑结构定线、测量和勘探程序的术语词汇》.pdf

BS 6954-1-1988 Tolerances for building - Recommendations for basic principles for evaluation and specification《建筑用公差 第1部分 评估基本原则和规范的推荐标准》.pdf

BS 6954-2-1988 Tolerances for building - Recommendations for statistical basis for predicting fit between components having a normal distribution of sizes《建筑用公差 第2部分 具有正态尺寸分布部件之间预配.pdf

BS 6954-3-1988 Tolerances for building Recommendations for selecting target size and predicting fit《建筑用公差 第3部分 选择对象尺寸和预配合推荐标准》.pdf

BS 6955-1-1994 Calibration of vibration and shock pick-ups - Methods for primary vibration calibration by laser interferometry《振动和冲击传感器的校准 采用激光干涉测量法对主振动的校准方法》.pdf

BS 6955-10-1994 Calibration of vibration and shock pick-ups - Method for primary calibration by high impact shocks《振动和冲击传感器的校准 采用强烈冲击法对主振动的校准方法》.pdf

BS 6955-12-1994 Calibration of vibration and shock pick-ups - Method of test for transverse shock sensitivity《振动和冲击传感器的校准 横向冲击灵敏度的试验方法》.pdf