CSN ON 17 7185-1964 《全铰链》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

STAS 9128-1980 TWIST DRILL WITH TAPER SHANK WITH CARBIDE TIP Dimensions《硬质合金刀头的锥形柄麻花钻 尺寸 》.pdf

STAS 9129-1980 TWIST DRILL WITH PARALLEL SHANK WITH CARBIDE TIP Dimensions《硬质合金刀头的平行柄麻花钻 尺寸 》.pdf

STAS 9130 1-1989 Cutting carbide tips for tools FRITTED HARDMETAL INDEXABLE CARBIDE TIPS WITH ROUNDED CORNER WITHOUT FIXING HOLE Dimensions《工具用的硬质合金刀头 多孔硬质合金圆角无固定孔可转位得硬质合金刀头仍 尺寸 》.pdf

STAS 9130 2-1989 Cutting carbide tips for tools FRITTED HARDMETAL INDE- XABLE CARBIDE TIPS WITH ROUNDED CORNER WITH CY- LINDRICAL FIXING HOLE Dimensions《工具用的硬质合金刀头多孔 硬质合金 柱状固定孔圆角硬质.pdf

STAS 9130 3-1989 Inserts for cutting tools INDEXABLE CARBIDE HARD METAL INSERTS WITH WIPER EDGES WITHOUT FIXING HOLE Dimensions《刀削工具用的刀片 带有滑动边缘无固定孔的可转位的碳化物硬质合金刀片尺寸 》.pdf

STAS 9130 4-1989 Boring tips for tools INDEXABLE HARDMETAL CAR- BIDE INSERTS WITH ROUNDED CORNERS WITSH CYLINDRICAL FIMNG HOLE AND INSERTS WITH an = 7 degrees normal clearance Dime.pdf

STAS 9130 5-1989 Cutting carbide tips for tools FRITTED HARDMETAL INDEXABLE CARBIDE TIPS WITH CHIP-BREAKER ON BOTH SIDES WITHOUT BORE Dimensions《工具用硬质合金刀头 无膛两面都带断屑台的多孔硬质合金硬质合金刀头 尺寸.pdf

STAS 9130 6-1989 Indexable inserts for culling tools lNDKXABI.K INSERTS Designation《剔出工具用的可转位的刀片 可转位 刀片标识 》.pdf

STAS 9131 1-1972 LEAD ALLOYS FOR STORAGE BATTERIES General directions for carrying out chemical analysis《蓄电池用的铅合金 进行化学分析的一般方向 》.pdf