1、September 2010 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).
2、ICS 85.100!$j5“1719418www.din.deDDIN EN 1034-2Safety of machinery Safety requirements for the design and construction of paper makingand finishing machines Part 2: Barking drums (includes Amendment A1:2009)English translation of DIN EN 1034-2:2010-09Sicherheit von Maschinen Sicherheitstechnische Anf
3、orderungen an Konstruktion und Bau von Maschinen derPapierherstellung und Ausrstung Teil 2: Entrindungstrommeln (enthlt nderung A1:2009)Englische bersetzung von DIN EN 1034-2:2010-09Scurit des machines Prescriptions de scurit pour la conception et la construction de machines de fabricationet de fini
4、tion du papier Partie 2: Tambours corceurs (Amendement A1:2009 inclus)Traduction anglaise de DIN EN 1034-2:2010-09SupersedesDIN EN 1034-2:2006-03See start of validitywww.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1508.10 DIN EN 10
5、34-2:2010-09 A comma is used as the decimal marker. Start of validity This standard takes effect on 1 September 2010. National foreword This standard includes safety requirements. This standard has been prepared by Technical Committee CEN/TC 198 “Printing and paper machinery Safety” (Secretariat: DI
6、N, Germany). The responsible German body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Working Committee NA 060-23-01 AA Druck- und Papier-maschinen of Section Druck- und Papiermaschinen. Representatives of manufacturers of paper makin
7、g and finishing machines, and of the employers liability insurance association for papermakers contributed to this standard. This standard contains specifications meeting the essential requirements set out in Annex I of the “Machinery Directive”, Directive 2006/42/EC, which took effect on 29 Decembe
8、r 2009, and which apply to machines that are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of these directives. Once this standard is cited in the Official Journal of the European Union, it is
9、deemed a “harmonized” standard and thus, a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). The European Standards referred to in this document have been published as the corresponding DIN EN or DIN EN ISO Stand
10、ards with the same number. For the International Standards referred to in this standard there are no national standards available unless they have been published as DIN ISO tandards with the same number. SAmendments This standard differs from DIN EN 1034-2:2006-03 as follows: a) the reference to EN
11、1034-1:2000+A1:2010 has been updated; b) item h) in Subclause 7.2 now expressly states that noise emission values are measured according to EN 13023:2003; c) an informative Annex ZB dealing with the relationship between this European Standard and the essential requirements of EU Directive 2006/42/EC
12、 has been included. Previous editions DIN EN 1034-2: 2006-03 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1034-2:2005+A1 December 2009 ICS 85.100 Supersedes EN 1034-2:2005English Version Safety of machinery - Safety requirements for the design and construction of paper making and finishing
13、 machines - Part 2: Barking drums Scurit des machines - Prescriptions de scurit pour la conception et la construction de machines de fabrication et de finition du papier - Partie 2: Tambours corceurs Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen
14、 der Papierherstellung und Ausrstung - Teil 2: Entrindungstrommeln This European Standard was approved by CEN on 10 November 2005 and includes Amendment 1 approved by CEN on 17 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
15、 giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three officia
16、l versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, B
17、elgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE
18、FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1034-2:2005+A1:2009: EEN 1034-2:2005+A1:200
19、9 (E) 2 Contents Page Foreword 3Introduction .41 Scope 42 Normative references 43 Terms and definitions .54 List of significant hazards 65 Safety requirements and/or measures 75.1 General 75.2 Mechanical hazards .85.3 Workplaces, access stairs, catwalks, passageways 85.4 Start-up warning device 85.5
20、 Emergency stop device .95.6 Means for isolation and energy dissipation, prevention of unexpected start-up .95.7 Equipment and measures for maintenance and repair and cleaning 95.8 Control systems and actuators 95.9 Noise .95.10 Integrated lighting. 105.11 Ergonomic principles . 105.12 Electrical eq
21、uipment . 105.13 Hydraulic equipment 105.14 Pneumatic equipment 105.15 Wood dust . 106 Verification of compliance with safety requirements and/or measures . 107 Information for use . 11Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 9
22、8/37/EC . 12Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 13Figure Figure 1 Example of a barking drum . 6 DIN EN 1034-2:2010-09 EN 1034-2:2005+A1:2009 (E) 3 Foreword This document (EN 1034-2:2005+A1:2009) has been prepa
23、red by Technical Committee CEN/TC 198 “Printing and paper machinery - Safety”, the secretariat of which is held by DIN. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national s
24、tandards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendme
25、nt 1, approved by CEN on 17 November 2009. This document supersedes EN 1034-2:2005. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade
26、 Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countr
27、ies are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain
28、, Sweden, Switzerland and United Kingdom. DIN EN 1034-2:2010-09 EN 1034-2:2005+A1:2009 (E) 4 Introduction This European Standard is a type C standard as stated in EN ISO 12100-1. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the
29、 scope of this European Standard. For machines that have been designed and built according to the provisions of this type C standard, the following stipulation applies: when provisions of this type C standard are different from those which are stated in type A or B standards or from provisions made
30、in !EN 1034-1:2000+A1:2010“, the provisions of this type C standard take precedence over the provisions of the other standards. 1 Scope This European Standard applies to barking drums consisting of drum, drive, power transmission elements, supporting wheels and control systems intended for use in de
31、barking plants for paper making and shall be used together with !EN 1034-1:2000+A1:2010“. It deals with all significant hazards, hazardous situations and hazard events relevant to barking drums, when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). This
32、 standard does not apply to sawing equipment or log and bark conveying systems used in debarking plants. This European Standard is not applicable to barking drums that have been manufactured before the date of publication of this European Standard by CEN. 2 Normative references The following referen
33、ced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery Safety distances to prevent danger zo
34、nes being reached by the upper limbs. EN 418:1992, Safety of machinery Emergency stop equipment, functional aspects Principles for design. EN 626-1:1994, Safety of machinery Reduction of risk to health from hazardous substances emitted by machinery Part 1: Principles and specifications for machinery
35、 manufacturers. EN 626-2:1996, Safety of machinery Reduction of risk to health from hazardous substances emitted by machinery Part 2: Methodology leading to verification procedures. EN 953:1997, Safety of machinery Guards General requirements for the design and construction of fixed and movable guar
36、ds. EN 954-1:1996, Safety of machinery Safety-related parts of control systems Part 1: General principles for design. EN 982:1996, Safety of machinery Safety requirements for fluid power systems and their components Hydraulics. DIN EN 1034-2:2010-09 EN 1034-2:2005+A1:2009 (E) 5 EN 983:1996, Safety o
37、f machinery Safety requirements for fluid power systems and their components Pneumatics. !EN 1034-1:2000+A1:2010“, Safety of machinery Safety requirements for the design and construction of paper making and finishing machines Part 1: Common requirements. EN 1050:1996, Safety of machinery Principles
38、for risk assessment. EN 1837:1999, Safety of machinery Integral lighting of machines. EN 13023:2003, Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment Accuracy categories 2 and 3. EN 60204-1:1997, Safety of machinery Electrical equipment of machi
39、nes Part 1: General requirements (IEC 60204-1:1997). EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989). EN 61000-6-2:2001, Electromagnetic compatibility (EMC) Part 6-2: Generic standards; immunity for industrial environment (IEC 61000-6-2:1999, modified). EN ISO
40、11957:1996, Acoustics Determination of sound insulation performance of cabins Laboratory and in situ measurements (ISO 11957:1996). EN ISO 12100-1:2003, Safety of machinery Basic concepts General principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003). EN ISO 12100-2:2003, Sa
41、fety of machinery Basic concepts General principles for design Part 2: Technical principles and specifications (ISO 12100-2:2003). EN ISO 14122-1:2001, Safety of machinery Permanent means of access to machinery Part 1: Choice of a fixed means of access between two levels (ISO 14122-1:2001). EN ISO 1
42、4122-2:2001, Safety of machinery Permanent means of access to machinery Part 2: Working platforms and gangways (ISO 14122-2:2001). EN ISO 14122-3:2001, Safety of machinery Permanent means of access to machinery Part 3: Stair, stepladders and guard-rails (ISO 14122-3:2001). EN ISO 14122-4:2004, Safet
43、y of machinery Permanent means of access to machinery Part 4: Fixed ladders (ISO 14122-4:2001). 3 Terms and definitions For the purposes of this document, the definitions of !EN 1034-1:2000+A1:2010“, EN ISO 12100-1:2003 and the following definition apply: 3.1 barking drum machine formed of a cylindr
44、ical hollow tube (drum) through which logs are fed. The rotation of the drum causes the logs to fall and be pushed against each other and rubbed against the inner wall of the drum causing the bark to break and fall off. Figure 1 illustrates the principle of a barking drum in a debarking plant DIN EN
45、 1034-2:2010-09 EN 1034-2:2005+A1:2009 (E) 6 Key 1 Drum 2 Drive 3 Supporting wheels 4 Discharge side 5, 6, 7, 8 Log conveyor belts NOTE: Safety devices are not shown. Figure 1 Example of a barking drum 4 List of significant hazards Table 1 of this clause contains all the significant hazards that, as
46、 far as they are dealt with in this standard, are identified by risk assessment in accordance with EN 1050 as significant for this type of machinery and require action to eliminate or reduce the risk. When carrying out the risk assessment, the machine designer has to check whether the list of hazard
47、s in Table 1 is complete and applicable with respect to his particular machine. DIN EN 1034-2:2010-09 EN 1034-2:2005+A1:2009 (E) 7 Table 1 List of significant hazards Hazards EN 1034-2:2005!EN 1034-1:2000+A1:2010“Mechanical hazards Crushing hazard 5.2.2; 5.2.6; 5.2.7 5.1; 5.3 Entanglement hazard 5.2
48、.1; 5.2.2 5.2 Drawing-in or trapping hazard 5.2.3; 5.2.5 5.1; 5.4 Impact hazard 5.2.4; 5.3.2 5.1 Friction or abrasion hazard 5.2.1 5.1High-pressure fluid ejection hazard 5.13; 5.14 5.24 Table 1 (concluded) Hazards EN 1034-2:2005!EN 1034-1:2000+A1:2010“Ejection of parts 5.2.4; 5.2.7 5.2 Slip, trip an
49、d fall hazards 5.2.4; 5.3; 5.7.2; 5.7.3 5.5 Electrical hazards caused by, for example:Electrical contact (direct or indirect) 5.12 5.23External influences on electrical equipment 5.12 5.23 Hazards generated by noise, resulting in Hearing loss (deafness), other physiological disorders (e.g. loss of balance, loss of awareness) 5.9 5.15Interferences
