1、June 2013 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91
2、.100.60!%1“2021496www.din.deDDIN EN 12089Thermal insulating products for building applications Determination of bending behaviour;English version EN 12089:2013,English translation of DIN EN 12089:2013-06Wrmedmmstoffe fr das Bauwesen Bestimmung des Verhaltens bei Biegebeanspruchung;Englische Fassung
3、EN 12089:2013,Englische bersetzung von DIN EN 12089:2013-06Produits isolants thermiques destins aux applications du btiment Dtermination du comportement en flexion;Version anglaise EN 12089:2013,Traduction anglaise de DIN EN 12089:2013-06SupersedesDIN EN 12089:1997-08www.beuth.deIn case of doubt, th
4、e German-language original shall be considered authoritative.Document comprises 13 pages 05.13 DIN EN 12089:2013-06 2 A comma is used as the decimal marker. National foreword This document (EN 12089:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”
5、(Secretariat: DIN, Germany) The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. The DIN Standards corresponding to the International Standards referred to in th
6、is document are as follows: ISO 5725-1 DIN ISO 5725-1 ISO 5725-2 DIN ISO 5725-2 Amendments This standard differs from DIN EN 12089:1997-08 as follows: a) the standard has been editorially revised. Previous editions DIN 1101: 1938-09, 1952x-01, 1960-10, 1970-04, 1980-03, 1989-11 DIN 1104-1: 1970-04,
7、1980-03 DIN EN 12089: 1997-08 National Annex NA (informative) Bibliography DIN ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions DIN ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basi
8、c method for the determination of repeatability and reproducibility of a standard measurement method EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12089 March 2013 ICS 91.100.60 Supersedes EN 12089:1997English Version Thermal insulating products for building applications - Determination of be
9、nding behaviour Produits isolants thermiques destins aux applications du btiment - Dtermination du comportement en flexion Wrmedmmstoffe fr das Bauwesen - Bestimmung des Verhaltens bei Biegebeanspruchung This European Standard was approved by CEN on 15 December 2012. CEN members are bound to comply
10、with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Ma
11、nagement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
12、status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M
13、alta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All righ
14、ts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12089:2013: EEN 12089:2013 (E) 2 Contents Page Foreword . 3 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5 4 Principle 6 5 Apparatus . 6 6 Test specimens 7 7 Procedure . 8 8 Calcu
15、lation and expression of results 9 9 Accuracy of measurement . 10 10 Test report 10 DIN EN 12089:2013-06 EN 12089:2013 (E) 3 Foreword This document (EN 12089:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulation materials and products”, the secretariat of which is held by DIN.
16、 This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that s
17、ome of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12089:1997. The revision of this standard contains no major changes, only minor corrections and clarif
18、ications of an editorial nature. This European Standard is one of a series of standards which specify test methods for determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which der
19、ive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted fo
20、r applications in buildings but it may also be used in other areas where it is relevant. This European test standard is one of the following group of inter-related standards on test methods for determining dimensions and properties of thermal insulation materials and products, all of which come with
21、in the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications Determination of length and width EN 823, Thermal insulating products for building applications Determination of thickness EN 824, Thermal insulating products for building applications Determination of squarenes
22、s EN 825, Thermal insulating products for building applications Determination of flatness EN 826, Thermal insulating products for building applications Determination of compression behaviour EN 1602, Thermal insulating products for building applications Determination of the apparent density EN 1603,
23、 Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 C/50 % relative humidity) EN 1604, Thermal insulating products for building applications Determination of dimensional stability under specified temperature an
24、d humidity conditions EN 1605, Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications Determination of compressive creep DIN EN 12089:2013-06 EN 1208
25、9:2013 (E) 4 EN 1607, Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1608, Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1609, Thermal insulating products for building ap
26、plications Determination of short-term water absorption by partial immersion EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test specimens EN 12086, Thermal insulating products for building applications Determination of water vapour transmission
27、 properties EN 12087, Thermal insulating products for building applications Determination of long-term water absorption by immersion EN 12088, Thermal insulating products for building applications Determination of long-term water absorption by diffusion EN 12089, Thermal insulating products for buil
28、ding applications Determination of bending behaviour EN 12090, Thermal insulating products for building applications Determination of shear behaviour EN 12091, Thermal insulating products for building applications Determination of freeze-thaw resistance EN 12429, Thermal insulating products for buil
29、ding applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12430, Thermal insulating products for building applications Determination of behaviour under point load EN 12431, Thermal insulating products for building applications Determination of thic
30、kness for floating floor insulating products EN 13793, Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13820, Thermal insulating materials for building applications Determination of organic content According to the CEN/CENELEC Internal Regulat
31、ions, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Ital
32、y, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 12089:2013-06 EN 12089:2013 (E) 5 1 Scope This European Standard specifies the equipment and procedures for determining the b
33、ending behaviour of full size products (Method A) and test specimens (Method B) under the action of three-point loading. It is applicable to thermal insulating products. The test is designed to determine the bending strength of products and their deflection at a given load. The method can be used to
34、 determine the resistance of the product to bending stresses during transport and application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited appl
35、ies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 822, Thermal insulating products for building applications Determination of length and width EN 823, Thermal insulating products for building applications Determination of thickness EN 1
36、2085, Thermal insulating products for building applications Determination of linear dimensions of test specimens ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions ISO 5725-2, Accuracy (trueness and precision) of measurement me
37、thods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 bending strength bmaximum stress calculated from the maximum fo
38、rce Fmrecorded during the bending procedure 3.2 bending stress xstress calculated from the force Fxat the deflection X 3.3 deflection X vertical displacement of the test specimen at mid span, at the force Fx, measured at the loading edge DIN EN 12089:2013-06 EN 12089:2013 (E) 6 4 Principle The test
39、method consists of applying, at a given speed, a force by means of a loading edge in an axial direction to the faces of a squarely cut rectangular test specimen, which is placed on two support edges. The force is applied to the test specimen at a position midway between the supporting positions (see
40、 Figure 1). a) Bending strength b) Deflection Figure 1 Principle of test method 5 Apparatus 5.1 Test machine A test machine suited to the range of force and displacement involved, and with a loading edge and adjustable support edges. It shall be capable of operating at a constant rate of movement of
41、 the movable head. 5.1.1 Support edges Test specimen supports shall consist of two adjustable cylindrical support edges placed parallel to each other and in the same horizontal plane. The diameter of the supports shall be (80 3) mm or (30 3) mm (see Figure 2). The length of the support edges shall b
42、e at least equal to the width of the test specimens. The span L (see Figure 2) between the support edges shall be adjustable in the range 300 mm to 1 200 mm (method A) or 200 mm to 500 mm (method B). 5.1.2 Loading edge The test specimen loading edge shall have the same shape and dimensions as the su
43、pport edges. The loading edge shall be located centrally between and parallel to the supporting edges. 5.1.3 Load distribution plates For products which may be subject to crushing by the loading and support edges, steel load distribution plates with a thickness of at least 1 mm shall be used. The wi
44、dth of the distribution plates shall be (30 1) mm and their length shall be at least equal to the width of the test specimen. DIN EN 12089:2013-06 EN 12089:2013 (E) 7 5.2 Measuring devices for displacement and force 5.2.1 Measurement of displacement The test machine shall be fitted with a system tha
45、t allows continuous measurement of the displacement of the movable loading edge with an accuracy of 5 % or 0,1 mm, whichever is the smaller. The measured displacement corresponds to the deflection, X, of the test specimen. 5.2.2 Measurement of force A force sensor shall be fixed to the loading edge
46、in order to measure the force F produced by the reaction of the test specimen upon the edges during the test. This sensor shall be such that its own deformation during the course of the measuring operation is negligible compared with that being measured or may be taken into account by calculation. I
47、n addition, it shall allow the continuous measurement of the force at all times permitting reading to 1 %. A device shall be used for the simultaneous recording of the force, F, and the deflection, X, to provide the force-deflection curve, required in Clause 7. 1 loading edge 2 test specimen with th
48、e thickness d 3 support edges a 50 mm for method A, 25 mm for method B Figure 2 Principles of apparatus for testing of bending behaviour 6 Test specimens 6.1 Dimensions of test specimens 6.1.1 Method A The test specimen is a full size product. It shall be a squarely cut rectangle having the following dimensions: Thickness: Original product thickness; Length: Length of the full size product, with a maximum of 1
