1、September 2012 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).
2、ICS 75.200!$V“1915159www.din.deDDIN EN 13012Petrol filling stations Construction and performance of automatic nozzles for use on fueldispensers;English version EN 13012:2012,English translation of DIN EN 13012:2012-09Tankstellen Anforderungen an Bau und Arbeitsweise von automatischen Zapfventilen fr
3、 dieBenutzung an Zapfsulen;Englische Fassung EN 13012:2012,Englische bersetzung von DIN EN 13012:2012-09Stations service Construction et performances des pistolets automatiques de remplissage utiliss sur lesdistributeurs de carburant;Version anglaise EN 13012:2012,Traduction anglaise de DIN EN 13012
4、:2012-09SupersedesDIN EN 13012:2002-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 22 pages 08.12 DIN EN 13012:2012-09 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee
5、CEN/TC 393 “Equipment for storage tanks and for filling stations” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Tankanlagen (Tank Installations Standards Committee), Working Committee NA 104-02-06 AA Abgabeeinrichtungen an Tank-stellen.
6、Amendments This standard differs from DIN EN 13012:2002-03 as follows: a) a new note has been added at the end of the scope: “Fuels other than of Explosion Group IIA are excluded from this European Standard”; b) an informative Annex C regarding environmental aspects has been included; c) normative r
7、eferences have been updated. Previous editions DIN EN 13012: 2002-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13012 June 2012 ICS 75.200 Supersedes EN 13012:2001English Version Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers Stations
8、-service - Construction et performances des pistolets automatiques de remplissage utiliss sur les distributeurs de carburant Tankstellen - Anforderungen an Bau und Arbeitsweise von automatischen Zapfventilen fr die Benutzung an Zapfsulen This European Standard was approved by CEN on 10 May 2012. CEN
9、 members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on appl
10、ication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Ma
11、nagement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Neth
12、erlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of expl
13、oitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13012:2012: EEN 13012:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .54 Construction .64.1 General 64.2 Guard 74.3 Inlet threads 74.4 Safe break .74.5 Latch .7
14、4.6 Automatic de-activating mechanism .75 Physical properties 86 Functional requirements .87 Frequency of testing .98 Marking 10Annex A (normative) Test preconditioning . 11A.1 General . 11A.2 Bending moment preconditioning 11A.3 Fuel compatibility pre-conditioning 11Annex B (normative) Test methods
15、 12B.1 Electrical resistance test 12B.2 Pressure test . 12B.3 Drop test 12B.4 Tightness test 12B.5 Automatic shut-off device test 1 . 13B.6 Drain test . 13B.7 Attitude device test 1 13B.8 Attitude device test 2 14B.9 Automatic de-activating mechanism test . 14B.10 Line shock generated test . 15B.11
16、Tightness test 15B.12 Automatic shut-off device test 2 . 15B.13 Attitude device test 3 15Annex C (informative) Environmental aspects 18Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives . 20 DIN EN 13012:2012-09 EN 13012:20
17、12 (E) 3 Foreword This document (EN 13012:2012) has been prepared by Technical Committee CEN/TC 393 “Equipment for This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2012, and conflicting na
18、tional standards shall be withdrawn at the latest by December 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supe
19、rsedes EN 13012:2001. Compared with the EN 13012:2001 version, the following fundamental changes have been made: a) a new note at the end of the scope was added: Fuels other than of Explosion Group IIA are excluded from this European Standard; b) an informative Annex C concerning environmental aspec
20、ts was added. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directives, see informative Annex ZA, which is an integral part of this documen
21、t. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irel
22、and, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13012:2012-09 storage tanks and for filling stations”, the secretariat of which is held by DIN. EN 13012:2012 (E) 4
23、1 Scope This European Standard specifies safety and environmental requirements for the construction and performance of nozzles to be fitted to metering pumps and dispensers installed at filling stations and which are used to dispense liquid fuels into the tanks of motor vehicles, boats and light air
24、craft and into portable containers, at flow rates up to 200 l min-1. The requirements apply to automatic nozzles dispensing flammable liquid fuels at ambient temperatures from 20 C to +40 C with the possibility for an extended temperature range. This European Standard does not apply to equipment dis
25、pensing liquefied petroleum gas nor compressed natural gas. This European Standard does not include any requirements for metering performance, such as may be specified under the Measuring Instruments Directive, nor those requirements specified under the Electromagnetic Compatibility Directive. Vapou
26、r recovery efficiency rates are not considered within this European Standard. NOTE 1 This European Standard does not apply to equipment for use with liquefied petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas (CNG). NOTE 2 Fuels other than of Explosion Group IIA are exclud
27、ed from this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenc
28、ed document (including any amendments) applies. EN 9761:1997, Underground tanks of glass-reinforced plastics (GRP) Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels Part 1: Requirements and test methods for single wall tanks EN 1360, Rubber and plastic hoses a
29、nd hose assemblies for measured fuel dispensing systems Specification EN 134631:2009, Non-electrical equipment for potentially explosive atmospheres Part 1: Basic method and requirements EN 136172, Petrol filling stations Part 2: Safety requirements for construction and performance of safe breaks fo
30、r use on metering pumps and dispensers EN 60079-0, Explosive atmospheres Part 0: Equipment General requirements (IEC 60079-0) EN 602041:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 602041:2005, modified) EN ISO 2281, Pipe threads where pressure-tight j
31、oints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) ISO 261, ISO general purpose metric screw threads General plan ISO 9652, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Me
32、dium quality ISO 9158, Road vehicles Nozzle spouts for unleaded gasoline DIN EN 13012:2012-09 EN 13012:2012 (E) 5 ISO 9159, Road vehicles Nozzle spouts for leaded gasoline and diesel fuel ISO 119253, Reaction to fire tests Ignitability of building products subjected to direct impingement of flame Pa
33、rt 3: Multi-source test 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 nozzle automatic delivery nozzle which is a manually operated device that controls the flow of fuel during a dispensing operation and includes a spout and an automatic sh
34、ut-off mechanism 3.2 vapour recovery nozzle delivery nozzle that additionally includes a path through which vapour can be recovered 3.3 automatic shut-off function that automatically stops the fluid flow to prevent overfilling 3.4 attitude device means to prevent delivery unless the spout is pointin
35、g down 3.5 automatic de-activating mechanism means to prevent flow if the system is re-energized while the operating lever is in an open position 3.6 operating device mechanism by which the main valve is controlled by the user 3.7 main valve device controlling the fluid flow 3.8 latch mechanism to h
36、old the operating lever in an open position 3.9 guard structure to protect the operating lever 3.10 spout device to guide the flow of fluid into a tank of a motor vehicle, boat and light aircraft or portable container 3.11 check valve device to restrict the hose draining through the nozzle DIN EN 13
37、012:2012-09 EN 13012:2012 (E) 6 3.12 flow rate flow of fluid obtained under normal working conditions Note 1 to entry: In l min-1 or m3h-1. 3.13 line shock peak pressure developed when fluid flow is stopped from full flow by the nozzle 3.14 spout axis angle angle of the spout axis to horizontal abov
38、e which no flow through the nozzle is allowed 3.15 maximum flow rate upper limit of flow rate range, specified by the manufacturer 4 Construction 4.1 General Materials used in the construction of nozzles shall be chemically and dimensionally stable under known service conditions. Materials likely to
39、 come into contact with fuels, both in liquid and vapour phases, shall be resistant to attack by these fuels. Conformity shall be demonstrated by manufacturers declarations and by the tests detailed in Annex B. The nozzle shall be explosion protected and shall be category 2 in accordance with EN 134
40、631. Components fitted to the spout and within the vapour recovery path shall be category 1 in accordance with EN 134631. The nozzle shall fulfil the requirements for temperature class T3 and group IIA according to EN 60079-0 or EN 134631. The nozzle shall have a manually controlled operating device
41、, which may incorporate an integral latch, to control the liquid flow. NOTE For safety reasons it might be necessary to operate without the latch. The surfaces and mechanisms of the nozzle which, in normal operation, come into contact with the operator shall be such that they present no risk of inju
42、ry. Conformity to this requirement is demonstrated by visual inspection of a nozzle. Nozzles shall be classified as Type I or Type II according to the delivery characteristics given in Table 1. Table 1 Types of construction Value Type I Type II maximum flow rate 80 l min-1 80 l min-1 200 l min-1dime
43、nsion of the spout According to ISO 9158 or ISO 9159 Not specified position of the sensor According to ISO 9158 or ISO 9159 50 mm from plane of spout tip spout axis angle 0 + 2 DIN EN 13012:2012-09 EN 13012:2012 (E) 7 4.2 Guard A guard shall be provided to prevent accidental misuse of the operating
44、device. 4.3 Inlet threads Inlet threads shall be of one of the following two styles. a) Style 1 for nozzles without a vapour recovery path. For nozzles without a vapour recovery path, using parallel threads for the hose connection in accordance with EN ISO 228-1, the sealing surfaces of the internal
45、 and external threads shall be designed such that they are suitable for use with flat gaskets. b) Style 2 for nozzles with a vapour recovery path. M 34 x 1,5 Female, in accordance with ISO 261 and ISO 965-2. The total thread depth shall be not less than 15,0 mm. The inlet end shall be machined to a
46、diameter of (35,0 0,05) mm for a length (6,0 0,1) mm. Inlet thread dimensions shall be in accordance with Table 2. Table 2 Thread specification for style 1 Nominal inlet size Female threads Male threads Maximum thread depth amm Minimum thread length bmm “ 12,5 11,01“ 15,5 14,01“ 15,5 17,5 1“ 15,5 18
47、,0a The thread depth, measured from the outer fore-part to the metallic inner sealing face. b The stated minimum length does only apply if the female thread of the hose fitting includes an inner flat gasket. In case of using an outer flat gasket, the male threads may be shorter as stated.4.4 Safe br
48、eak Where a nozzle is provided with a safe break this shall fulfil the requirements according to EN 136172. 4.5 Latch Where a latch is provided and in use, it should be capable of being normally disarmed by the user. 4.6 Automatic de-activating mechanism If an automatic de-activating mechanism entirely in the nozzle exists, it shall fulfil the requirements according to Table 4. DIN EN 13012:2012-09 EN
