1、November 2006DEUTSCHE NORM Normenausschuss Luft- und Raumfahrt (NL) im DINPreisgruppe 12DIN Deutsches Institut fr Normung e.V. Jede Art der Vervielfltigung, auch auszugsweise, nur mit Genehmigung des DIN Deutsches Institut fr Normung e.V., Berlin, gestattet.ICS 49.080!,c;4“9642417www.din.deDDIN EN 4
2、167Luft- und Raumfahrt Rohrschellen, federnd, dreiteilig Innenschelle aus hochwarmfestem Stahl FE-PA2601 (A286);Deutsche und Englische Fassung EN 4167:2004Aerospace series Clips, spring tension, three parts Inner clips in heat resisting steel FE-PA2601 (A286);German and English version EN 4167:2004S
3、rie arospatiale Colliers de fixation ressort en trois parties Demi-colliers intrieurs, en acier rsistant chaud FE-PA2601 (A286);Version allemande et anglaise EN 4167:2004Alleinverkauf der Normen durch Beuth Verlag GmbH, 10772 Berlinwww.beuth.deGesamtumfang 14 SeitenDIN EN 4167:2006-11 2 Nationales V
4、orwort Die Europische Vereinigung der Hersteller von Luft- und Raumfahrtgert (AECMA) ist vom Europischen Komitee fr Normung (CEN) fr zustndig erklrt worden, Europische Normen (EN) fr das Gebiet der Luft- und Raumfahrt auszuarbeiten. Durch die Vereinbarung vom 3. Oktober 1986 wurde AECMA Assoziierte
5、Organisation (ASB) des CEN. Die vorliegende Norm EN 4167:2004 wurde von AECMA-STAN Fachbereich Mechanik unter Mitwirkung deutscher Experten des Normenausschusses Luft- und Raumfahrt erarbeitet. Entsprechend Beschluss 57/9 des Technischen Ausschusses des Beirats des Normenausschusses Luft- und Raumfa
6、hrt (NL) im DIN Deutsches Institut fr Normung e. V. sind die europischen Luft- und Raumfahrt-Normungsergebnisse zweisprachig, in Deutsch und Englisch, in das Deutsche Normenwerk zu berfhren. Aus diesem Grund wurde der Deutschen Fassung dieser EN-Norm die Englische Fassung hinzugefgt. EUROPISCHE NORM
7、 EUROPEAN STANDARD NORME EUROPENNE EN 4167 Dezember 2004 ICS 49.080 Ersatz fr EN 4167:2003 Deutsche Fassung Luft- und Raumfahrt - Rohrschellen, federnd, dreiteilig - Innenschelle aus hochwarmfestem Stahl FE-PA2601 (A286) Aerospace series - Clips, spring tension, three parts - Inner clips in heat res
8、isting steel FE-PA2601 (A286) Srie arospatiale - Colliers de fixation ressort en trois parties - Demi-colliers intrieurs, en acier rsistant chaud FE-PA2601 (A286) Diese Europische Norm wurde vom CEN am 11. September 2003 angenommen. Die CEN-Mitglieder sind gehalten, die CEN/CENELEC-Geschftsordnung z
9、u erfllen, in der die Bedingungen festgelegt sind, unter denen dieser Europischen Norm ohne jede nderung der Status einer nationalen Norm zu geben ist. Auf dem letzten Stand befindliche Listen dieser nationalen Normen mit ihren bibliographischen Angaben sind beim Management-Zentrum oder bei jedem CE
10、N-Mitglied auf Anfrage erhltlich. Diese Europische Norm besteht in drei offiziellen Fassungen (Deutsch, Englisch, Franzsisch). Eine Fassung in einer anderen Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch bersetzung in seine Landessprache gemacht und dem Management-Zentrum mitgete
11、ilt worden ist, hat den gleichen Status wie die offiziellen Fassungen. CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Dnemark, Deutschland, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Lettland, Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, sterre
12、ich, Polen, Portugal, Schweden, der Schweiz, der Slowakei, Slowenien, Spanien, der Tschechischen Republik, Ungarn, dem Vereinigten Knigreich und Zypern. Management-Zentrum: rue de Stassart, 36 B-1050 Brssel 2004 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Verfahren, sind we
13、ltweit den nationalen Mitgliedern von CEN vorbehalten. Ref. Nr. EN 4167:2004 DEUROPISCHES KOMITEE FR NORMUNGEUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEN 4167:2004 (D) 2 Inhalt Seite Vorwort 3 1 Anwendungsbereich .4 2 Normative Verweisungen4 3 Anforderungen.4 3.1 Ausfhrung M
14、ae Grenzabmae 4 3.2 Werkstoff 4 3.3 Oberflchenbehandlung .4 3.4 Wrmebehandlung.5 3.5 Hrte5 4 Bezeichnung.6 5 Kennzeichnung 6 6 Qualittssicherung 6 EN 4167:2004 (D) 3 Vorwort Dieses Dokument (EN 4167:2004) wurde vom Verband der Europischen Luft- und Raumfahrtindustrie Standardisierung (AECMA-STAN) er
15、stellt. Nachdem Umfragen und Abstimmungen entsprechend den Regeln dieses Verbandes durchgefhrt wurden, hat diese Norm die Zustimmung der nationalen Verbnde und offiziellen Behrden der Mitgliedslnder der AECMA erhalten, bevor sie CEN vorgelegt wurde. Diese Europische Norm muss den Status einer nation
16、alen Norm erhalten, entweder durch Verffentlichung eines identischen Textes oder durch Anerkennung bis Juni 2005, und etwaige entgegenstehende nationale Normen mssen bis Juni 2005 zurckgezogen werden. Diese Europische Norm ersetzt EN 4167:2003. Entsprechend der CEN/CENELEC-Geschftsordnung sind die n
17、ationalen Normungsinstitute der folgenden Lnder gehalten, diese Europische Norm zu bernehmen: Belgien, Dnemark, Deutschland, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Lettland, Litauen, Luxemburg, Malta, Niederlande, Norwegen, sterreich, Polen, Portugal, Schweden, Schweiz
18、, Slowakei, Slowenien, Spanien, Tschechische Republik, Ungarn, Vereinigtes Knigreich und Zypern. EN 4167:2004 (D) 4 1 Anwendungsbereich Diese Norm legt die Eigenschaften von Innenschellen aus FE-PA2601 (A286) fr dreiteilige, federnde Rohrschellen fr Anwendungen bei einer Temperatur von max. 260 C fe
19、st. Sie sind mit Teilen nach EN 4166 und EN 4168 zusammenzubauen. 2 Normative Verweisungen Die folgenden zitierten Dokumente sind fr die Anwendung dieses Dokuments erforderlich. Bei datierten Verwei-sungen gilt nur die in Bezug genommene Ausgabe. Bei undatierten Verweisungen gilt die letzte Ausgabe
20、des in Bezug genommenen Dokuments (einschlielich aller nderungen). EN 2424, Luft- und Raumfahrt Kennzeichnung von Luft- und Raumfahrtteilen EN 2516, Luft- und Raumfahrt Passivieren von korrosionsbestndigen Sthlen und Dekontaminierung von Nickellegierungen EN 3638, Luft- und Raumfahrt Hochwarmfeste L
21、egierung FE-PA2601 (X6NiCrTiMoV26-15), mit selbst-verzehrender Elektrode umgeschmolzen, lsungsgeglht und ausgelagert Bleche, Bnder und Platten 0,5 mm a 10 mm1)EN 4166, Luft- und Raumfahrt Rohrschellen, federnd, dreiteilig Hlsen aus PTFE EN 4168, Luft- und Raumfahrt Rohrschellen, federnd, dreiteilig
22、Auenschelle aus hochwarmfestem Stahl FE-PA2601 (A286)EN 9100, Luft- und Raumfahrt Qualittsmanagementsysteme Anforderungen (basiert auf ISO 9001:2000) und Qualittssysteme Qualittssicherungsmodelle fr Konstruktion, Entwicklung, Produktion, Montage und Wartung (basiert auf ISO 9001:1994) 3 Anforderunge
23、n 3.1 Ausfhrung Mae Grenzabmae Siehe Bild 1 und Tabelle 1. Die Mae und Grenzabmae sind in Millimeter angegeben und gelten nach dem Passivieren. 3.2 Werkstoff EN 3638. 3.3 Oberflchenbehandlung EN 2516. 1) Verffentlicht als AECMA-Vornorm zum Zeitpunkt der Herausgabe dieser Norm EN 4167:2004 (D) 5 3.4
24、Wrmebehandlung Ausgehrtet nach der Formgebung. 3.5 Hrte HV = 260 bis 345. Legende 1 Kanten gratfrei 0,1 bis 0,4 5 Kennzeichnung 2 10,4 bis 10,8 6 6 bis 6,2 3 Faserrichtung 7 2 bis 2,3 4 R = 7 bis 9 Bild 1 EN 4167:2004 (D) 6 Tabelle 1 A B E F Masse kg/1 000 Stck Durch- messer- Kennzahl max. min. max.
25、 min. max. min. max. min. 004 7,8 7,2 13,6 13,1 17 006 9,8 9,2 14,5 14 19 008 11,8 11,2 15,5 15 22 010 13,8 13,2 16,4 15,9 0,9 0,7 25 012 15,8 15 17,8 17,3 36 014 17,8 17 18,7 18,2 39 016 19,8 19 19,6 19,1 43 018 18 21,8 21 20,5 48 020 23,8 23 21,5 21 50 025 28,8 28 24 23,5 58 032 35,8 35 27,5 27 1,
26、1 0,9 5,8 5,5 71 4 Bezeichnung BEISPIEL Benennungsblock Identifizierungsblock INNENSCHELLE EN4167 - 012 Nummer dieser Norm Durchmesser-Kennzahl (siehe Tabelle 1) ANMERKUNG Wenn erforderlich, muss das Kennzeichen I9005 zwischen den Benennungsblock und den Identifizierungs-block eingefgt werden. 5 Ken
27、nzeichnung EN 2424, Klasse A, wie in Bild 1 angegeben. 6 Qualittssicherung Das Qualittssystem des Herstellers muss konform sein mit EN 9100. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4167 December 2004 ICS 49.080 Supersedes EN 4167:2003 English version Aerospace series - Clips, spring ten
28、sion, three parts - Inner clips in heat resisting steel FE-PA2601 (A286) Srie arospatiale - Colliers de fixation ressort en trois parties - Demi-colliers intrieurs, en acier rsistant chaud FE-PA2601 (A286) Luft- und Raumfahrt - Rohrschellen, federnd, dreiteilig - Innenschelle aus hochwarmfestem Stah
29、l FE-PA2601 (A286) This European Standard was approved by CEN on 11 September 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists an
30、d bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibi
31、lity of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, I
32、taly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nat
33、ional Members. Ref. No. EN 4167:2004: EEUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG EN 4167:2004 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Required characteristics.4 4 Designation 6 5 Marking .6 6 Quality assurance6 EN 4
34、167:2004 (E) 3 Foreword This document (EN 4167:2004) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the Nationa
35、l Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national sta
36、ndards shall be withdrawn at the latest by June 2005. This document supersedes EN 4167:2003. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Den
37、mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4167:2004 (E) 4 1 Scope This standard specifies the characteristic
38、s of inner clips, three part clips, spring tension, in FE-PA2601 for applications at a maximum temperature of 260 C, for aerospace applications. They shall be assembled with parts from EN 4166 and EN 4168. 2 Normative references The following referenced documents are indispensable for the applicatio
39、n of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 2516, Aerospace series Passivation of corrosion resisting ste
40、els and decontamination of nickel base alloys EN 3638, Aerospace series Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) Consumable electrode remelted Solution and precipitation treated Sheet, strip and plate 0,5 mm a 10 mm 1)EN 4166, Aerospace series Clips, spring tension, three parts PTFE bushes
41、EN 4168, Aerospace series Clips, spring tension, three parts Outer clips in heat resisting steel FE-PA2601 (A286) EN 9100, Aerospace series - Quality management systems - Requirements (based on ISO 9001:2000) and Quality systems - Model for quality assurance in design, development, production, insta
42、llation and servicing (based on ISO 9001:1994) 3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. They apply after passivation. 3.2 Materials EN 3638 3.3 Surface treatment EN 2516 3.4 Heat surface Precipit
43、ation heat treated after forming 3.5 Hardness 260 HV to 345 HV 1) Published as AECMA Prestandard at the date of publication of this standard EN 4167:2004 (E) 5 Key 1 break sharp edges 0,1 to 0,4 2 10,4 to 10,8 3 direction of grain 4 R = 7 to 9 5 marking 6 6 to 6,2 7 2 to 2,3 Figure 1 Table 1 Diamete
44、r code A B E F Mass kg/1 000 parts max. min. max. min. max. min. max. min. 004 7,8 7,2 13,6 13,1 17 006 9,8 9,2 14,5 14 19 008 11,8 11,2 15,5 15 22 010 13,8 13,2 16,4 15,9 0,9 0,7 25 012 15,8 15 17,8 17,3 36 014 17,8 17 18,7 18,2 39 016 19,8 19 19,6 19,1 43 018 18 21,8 21 20,5 48 020 23,8 23 21,5 21
45、 50 025 28,8 28 24 23,5 58 032 35,8 35 27,5 27 1,1 0,9 5,8 5,5 71 EN 4167:2004 (E) 6 4 Designation EXAMPLE Description block INNER CLIP Identity block EN4167-012 Number of this standard Diameter code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style A, as indicated on Figure 1. 6 Quality assurance The manufacturers quality systems shall conform to EN 9100.