1、January 2013 Translation by DIN-Sprachendienst.English price group 21No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 79.120.10!$gB“1936831www.din.deDDIN EN 848-2Safety of woodworking machines One side moulding machines with rotating tool Part 2: Single spindle hand fed/integrated fed routing machines;English version EN 848-2:2007+A2:2012,English translation of DIN EN 848-2:2013-01Sicherheit von Holzbearbeitungsm
3、aschinen Frsmaschinen fr einseitige Bearbeitung mit drehendem Werkzeug Teil 2: Einspindelige Oberfrsmaschinen mit Handvorschub/mechanischem Vorschub;Englische Fassung EN 848-2:2007+A2:2012,Englische bersetzung von DIN EN 848-2:2013-01Scurit des machines pour le travail du bois Machines fraiser sur u
4、ne face outil rotatif Partie 2: Dfonceuses monobroche avance manuelle/mcanise;Version anglaise EN 848-2:2007+A2:2012,Traduction anglaise de DIN EN 848-2:2013-01SupersedesDIN EN 848-2:2010-04www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprise
5、s 65 pages 12.12 DIN EN 848-2:2013-01 2 A comma is used as the decimal marker. National foreword This standard includes safety requirements. This document (EN 848-2:2007+A2:2012) has been prepared by Technical Committee CEN/TC 142 “Wood-working machines Safety” (Secretariat: UNI, Italy). The respons
6、ible German body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Working Committee NA 060-06-01 AA Holzbearbeitungs-maschinen Sicherheit of Section Holzbearbeitungsmaschinen. Representatives of manufacturers and users of single spindle h
7、and fed/integrated fed routing machines, and of the employers liability insurance associations contributed to this standard. This standard contains specifications meeting the essential requirements set out in Annex I of the “Machinery Directive”, Directive 2006/42/EC, and which apply to machines tha
8、t are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of that directive. Once this standard is cited in the Official Journal of the European Union, it is deemed a “harmonized” standard and thus,
9、a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). The European Standards referred to in Clause 2 and in the Bibliography of the EN have been published as the corresponding DIN EN or DIN EN ISO Standards with th
10、e same number. Where the International Standards referred to are not also DIN ISO Standards with the same number, there are no national standards available, except for: HD 22.4 S4:2004 DIN EN 50525-2-21 Amendments This standard differs from DIN EN 848-2:2010-04 as follows: a) Clause 1 “Scope” has be
11、en extended to include machines used for working hardened plastic materials with similar physical characteristics as wood; b) Clause 2 “Normative references” has been updated; c) in Subclause 5.2 “Controls” the design requirements for control circuits in certain categories have been replaced by spec
12、ifications for performance levels; d) the former Subclause 5.2.1.2 “Use of well-tried components” has been deleted; e) the former Subclause 5.2.8 “Spindle speed monitoring” has been completely revised and the title has been replaced with “Spindle speed control”; f) Subclause 5.3.4 “Braking” has been
13、 completely revised; g) Subclause 5.3.5 “Devices to minimise the possibility or the effect of ejection” now includes the description and an example of an enveloping guard; DIN EN 848-2:2013-01 3 h) Annex C (normative) “Impact test method for guards” has been added including tests on guards materials
14、, unless they are in accordance with Subclause 5.3.8 “Characteristics of guards and safety devices”; i) Subclause 5.4.3 “Emission of chips and dust” has been revised to include further requirements; j) the former Annex A (informative) “Use of well tried components” has been deleted; k) Annex ZA (inf
15、ormative) “Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC” has been deleted; l) the former Annex ZB is now Annex ZA (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC”; m) the Bibli
16、ography has been updated. Previous editions DIN EN 848-2: 1998-11, 2007-07, 2010-04 DIN EN 848-2:2013-01 4 National Annex NA (informative) Bibliography DIN EN 50525-2-21, Electric cables Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) Part 2-21: Cables for general ap
17、plications Flexible cables with crosslinked elastomeric insulation EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 848-2:2007+A2 September 2012 ICS 79.120.10 Supersedes EN 848-2:2007+A1:2009English Version Safety of woodworking machines - One side moulding machines with rotating tool - Part 2:
18、Single spindle hand fed/integrated fed routing machines Scurit des machines pour le travail du bois - Machines fraiser sur une face, outil rotatif - Partie 2: Dfonceuses monobroche avance manuelle/mcanise Sicherheit von Holzbearbeitungsmaschinen - Frsmaschinen fr einseitige Bearbeitung mit drehendem
19、 Werkzeug - Teil 2: Einspindelige Oberfrsmaschinen mit Handvorschub/mechanischem Vorschub This European Standard was approved by CEN on 13 January 2007 and includes Amendment 1 approved by CEN on 3 October 2009 and Amendment 2 approved by CEN on 13 August 2012. CEN members are bound to comply with t
20、he CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Manageme
21、nt Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status
22、 as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
23、Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of
24、exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 848-2:2007+A2:2012: EEN 848-2:2007+A2:2012 (E) 2 Contents Page Foreword 4Introduction .51 Scope 62 Normative references 63 Terms and definitions .93.1 General 93.2 Definitions 93.3 Terms . 164 List of
25、significant hazards . 175 Safety requirements and/or measures . 205.1 General . 205.2 Controls . 205.2.1 Safety and reliability of control systems 205.2.2 Position of controls 215.2.3 Starting 225.2.4 Normal stopping . 235.2.5 Additional stop 235.2.6 Emergency stop 245.2.7 Mode selection 245.2.8 #Sp
26、indle speed control$ . 255.2.9 Integrated feed 265.2.10 Failure of the power supply . 265.2.11 Failure of the control circuits 265.3 Protection against mechanical hazards . 275.3.1 Stability 275.3.2 Hazard of break up during operation 275.3.3 Tool holder and tool design . 275.3.4 Braking . 295.3.5 D
27、evices to minimise the possibility or the effect of ejection . 305.3.6 Workpiece supports and guides . 325.3.7 Prevention of access to moving parts 355.3.8 Characteristics of guards and safety devices . 375.3.9 Clamping device . 375.3.10 Safety appliances 375.4 Protection against non mechanical haza
28、rds . 385.4.1 Fire . 385.4.2 Noise 385.4.3 Emission of chips and dust . 395.4.4 Electricity . 405.4.5 Ergonomics and handling 415.4.6 Pneumatics 415.4.7 Hydraulics 415.4.8 Electromagnetic compatibility . 415.4.9 Static electricity 425.4.10 Errors of fitting 425.4.11 Supply disconnecting devices 425.
29、4.12 Maintenance 426 Information for use . 43DIN EN 848-2:2013-01 EN 848-2:2007+A2:2012 (E) 3 6.1 Warning devices 436.2 Marking . 436.3 Instruction handbook 44Annex A (normative) Stability test for displaceable machines 50Annex B (normative) Braking tests . 51B.1 Conditions for all tests 51B.2.1 Un-
30、braked run-down time . 51B.2.2 Braked run-down time . 51Annex C (normative) #Impact test method for guards$ . 52C.1 General . 52C.2 Test method . 52C.2.1 Preliminary remarks 52C.2.2 Testing equipment . 52C.2.3 Projectile for guards 52C.2.4 Sampling. 52C.2.5 Test procedure . 52C.3 Results 53C.4 Asses
31、sment . 53C.5 Test report 53C.6 Test equipment for impact test 53Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 56Bibliography 60DIN EN 848-2:2013-01 EN 848-2:2007+A2:2012 (E) 4 Foreword This document (EN 848-2:2007+A2:2
32、012) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2013, and c
33、onflicting national standards shall be withdrawn at the latest by March 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This doc
34、ument includes Amendment 1, approved by CEN on 2009-10-03 and Amendment 2, approved by CEN on 2012-08-13. This document supersedes #EN 848-2:2007+A1:2009$. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “ and #$XThis document has been prepared unde
35、r a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the !Machinery Directives“. !For relationship with EU Directive(s), see informative #Annexe ZA, which is an integral part$ of this document.“ Organisation contributing
36、to the preparation of this document include the European Association of Manufacturer of Woodworking Machines “EUMABOIS“. The European Standards produced by CEN/TC 142 are particular to woodworking machines and compliment the relevant A and B standards on the subject of general safety (see introducti
37、on of #EN ISO 12100:2010$ for a description of A, B and C standards). !EN 848 Safety of woodworking machines One side moulding machines with rotating tool consists of the following parts: Part 1: Single spindle vertical moulding machines Part 2: Single spindle hand fed/integrated fed routing machine
38、s Part 3: Numerically controlled (NC) boring and routing machines“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, E
39、stonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 848-2:2013-01
40、 EN 848-2:2007+A2:2012 (E) 5 Introduction This document has been prepared to be a harmonised standard to provide one means of conforming to the essential safety requirements of the Machinery Directive and associated EFTA Regulations. This document is a type C standard as stated in #EN ISO 12100:2010
41、$. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take
42、 precedence over the provisions of other standards, for machines that have been designed and built according to the provisions of this type C standard. The requirements of this document are directed to manufacturers and their authorised representatives of single spindle hand fed/integrated fed routi
43、ng machines. It is also useful for designers. This document also includes examples of information which are to be provided by the manufacturer to the user. Common requirements for tooling are given in #EN 847-1:2005+A1:2007$, EN 847-2:2001 and EN 847-3:2004. DIN EN 848-2:2013-01 EN 848-2:2007+A2:201
44、2 (E) 6 1 Scope This document !specifies all significant“ hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable single spindle hand fed/integrated fed routing machines with fixed head but allowing only movement along the axis of the tool dur
45、ing machining hereinafter referred to as “machines“ designed to cut solid wood, chip board, fibreboard, plywood and also these materials if they are covered with plastic laminate, edgings or veneer when they are used as intended and under the conditions foreseen by the manufacturer #including reason
46、ably foreseeable misuse$. #For the definition of stationary and displaceable machine see 3.2.17 and 3.2.18. Machines which are designed to work wood based materials may also be used for working hardened plastic materials with similar physical characteristics as wood.$ This document does not apply to
47、: a) inverted pin routers and radial arm routers (machines where the work piece is fixed and the tool head is manually moved); b) NC boring machines and NC routing machines; #NC boring machines and NC routing machines are dealt with in EN 848-3:2007+A1:2009.$ c) hand-held routers or any adaptation p
48、ermitting their use in a different mode, e.g. bench mounting; #NOTE 1$ Hand-held motor-operated electric tools are dealt with in #EN 60745-1:2009$ together with EN 60745-2-17:2003. d) routing machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench
