1、July 2014 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55
2、.100!%5zl“2188773www.din.deDDIN EN 16288-1Glass packaging Screw finishes for pressure capsules Part 1: Returnable glass MCA 3 finish;English version EN 16288-1:2014,English translation of DIN EN 16288-1:2014-07Verpackungen aus Glas Schraubmundstcke fr Flaschen mit Innendruck Teil 1: Mehrweg-MCA 3-(G
3、las-)Mundstck;Englische Fassung EN 16288-1:2014,Englische bersetzung von DIN EN 16288-1:2014-07Emballage en verre Bagues vis pour capsules pression Partie 1: Bague MCA 3 pour verre consign;Version anglaise EN 16288-1:2014,Traduction anglaise de DIN EN 16288-1:2014-07www.beuth.deIn case of doubt, the
4、 German-language original shall be considered authoritative.Document comprises 12 pages 06.14 DIN EN 16288-1:2014-07 2 A comma is used as the decimal marker. National foreword This document (EN 16288-1:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France)
5、. The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Working Committee NA 115-02-04 AA Behltnisse aus Glas. In addition to the legal units of measurement, this standard also uses the unit “in” (inch). It should be noted t
6、hat the Gesetz ber Einheiten im Messwesen (German Law on units in metrology) prohibits the use of this unit for official and commercial purposes in Germany. Conversion: Non-SI unit SI unit Conversion in (inch) mm 1 in = 25,4 mm EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16288-1 March 2014
7、ICS 55.100 English Version Glass packaging - Screw finishes for pressure capsules - Part 1: Returnable glass MCA 3 finish Emballage en verre - Bagues vis pour capsules pression - Partie 1: Bague MCA 3 pour verre consign Verpackungen aus Glas - Schraubmundstcke fr Flaschen mit Innendruck - Teil 1: Me
8、hrweg-MCA 3-(Glas-)MundstckThis European Standard was approved by CEN on 12 January 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date li
9、sts and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation unde
10、r the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Y
11、ugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EURO
12、PEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16288-1:2014 EEN 16288-1:2014 (E) 2 Contents Page Foreword 3
13、Introduction .4 1 Scope 5 2 Terms and definitions .5 3 Dimensions .5 Bibliography . 10 DIN EN 16288-1:2014-07 EN 16288-1:2014 (E) 3 Foreword This document (EN 16288-1:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Stand
14、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2014 and conflicting national standards shall be withdrawn at the latest by September 2014. Attention is drawn to the possibility that some of the elements o
15、f this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 16288, Glass packaging Screw finishes for pressure capsules, consists of the following parts: Part 1: Returnable glass MCA 3 finish Part 2: One way
16、glass MCA 3 finish According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mac
17、edonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DINEN 16288-1:2014-07EN 16288-1:2014(E)4 Introduction This European
18、Standard is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 32.01.1Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents
19、of the pack. DINEN 16288-1:2014-07EN 16288-1:2014(E)5 1 Scope This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 3 for pressurized or vacuum liquids for returnable glass. 2 Terms and definitions For the purposes of this document, the followi
20、ng term and definition applies. 2.1 MCA (glass) finish designed for the closure of pressurized or vacuum liquids with a tamper-evident closure (metal or plastic) 3 Dimensions The design and dimensions of the finish shall be as shown in Table 1 and Figure 1, Figure 2, Figure 3, Figure 4 and Figure 5.
21、 Table 1 Design and dimensions of the finish Pitch TPI cutter 3,175 mm 2 12 8 12,5 mm = Helix angle or angle or fixture to cutter. NOTE TPI = Threads per Inch. One inch is equal to 25,4 mm. The Tan of helix angle for cutter is calculated via the following formula: ( )2nominalnominalpitchTanET += whe
22、re T is the thread diameter; E is the wall diameter of threaded finish. The average of the maximum and minimum of L diameter is as close as possible to L nominal. The mean diameter 2mindiametermaxdiameter +L is in the tolerance of 0,2 mm. Optional: Depressed thread at mould parting line (see EN 1629
23、2). DINEN 16288-1:2014-07EN 16288-1:2014(E)6 Dimensions in millimetres Key N Neck (under bead) diameter H Thread height S Start of thread position from sealing surface to intersection of thread flank F Height of the finish L Locking bead diameter T Thread diameter E Wall diameter of threaded finish
24、NOTE Bore diameter (17,0 0,5) mm for a depth of 3 mm Figure 1 MCA 3 finish DIN EN 16288-1:2014-07 EN 16288-1:2014(E)7 Dimensions in millimetres Type 1 Type 2 Key a Mould parting line b Sealing surface Figure 2 Possible alternative constructions of the bore entrance to suit glass manufacturer The sea
25、ling surface is smooth and free of any defects and flash. DIN EN 16288-1:2014-07 EN 16288-1:2014 (E) 8 Dimensions in millimetres Minimum through bore 16,0 Figure 3 Detail of the profile DIN EN 16288-1:2014-07 EN 16288-1:2014 (E) 9 NOTE Z-Z is the last full depth and width of thread. Beyond this poin
26、t and Y-Y, the thread root is gradually increased to full thread diameter T in 90. Figure 4 Run out of thread Dimensions in millimetres Figure 5 Limit of construction DIN EN 16288-1:2014-07 EN 16288-1:2014 (E) 10 Bibliography 1 CE. T.I.E. data sheet GME 32.01- MCA 3 finish 1)2 EN 16292, Glass packaging - Screw finishes - Depressed threads 1) Obtainable through Centre Technique International de lEmbouteillage et du Conditionnement (CE.T.I.E), 112- 114, rue La Botie, 75008 Paris, France www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. DINEN 16288-1:2014-07
