1、May 2017 English price group 17No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 11.180.01; 45.060.20!%e_$“2666001www
2、.din.deDIN EN 16585-1Railway applications Design for PRM use Equipment and components onboard rolling stock Part 1: Toilets;English version EN 165851:2017,English translation of DIN EN 16585-1:2017-05Bahnanwendungen Gestaltung fr die Nutzung durch PRM Ausstattung und Bauteile in Schienenfahrzeugen T
3、eil 1: Toiletten;Englische Fassung EN 165851:2017,Englische bersetzung von DIN EN 16585-1:2017-05Applications ferroviaires Conception destine lusage par les PMR Equipements et lments bord du matriel roulant Partie 1: Toilettes;Version anglaise EN 165851:2017,Traduction anglaise de DIN EN 16585-1:201
4、7-05SupersedesDIN CEN/TS 16635(DIN SPEC 5523):201411www.beuth.deDocument comprises 42 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.05.17 DIN EN 16585-1:2017-05 2 A comma is used as the decimal marker. National foreword This
5、document (EN 16585-1:2017) has been prepared by Technical Committee CEN/TC 256 “Railway applications” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was DIN-Normenausschuss Fahrweg und Schienenfahrzeuge (DIN Standards Committee Railway), Subcommittee NA 087-00-1
6、1-02 UA “Vehicles and infrastructure for people with reduced mobility”. This standard is based on the English reference version. This document supersedes DIN CEN/TS 16635:2014-11. Previous editions DIN CEN/TS 16635 (DIN SPEC 5523): 2014-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16585-1
7、 January 2017 ICS 11.180.01; 45.060.20 Supersedes CEN/TS 16635:2014English Version Railway applications - Design for PRM use - Equipment and components onboard rolling stock - Part 1: Toilets Applications ferroviaires - Conception destine lusage par les PMR - Equipements et lments bord du matriel ro
8、ulant - Partie 1 : Toilettes Bahnanwendungen - Gestaltung fr die Nutzung durch PRM - Ausstattung und Bauteile in Schienenfahrzeugen -Teil 1: Toiletten This European Standard was approved by CEN on 26 September 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stip
9、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European
10、Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the
11、 national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania
12、, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form a
13、nd by any means reserved worldwide for CEN national Members. Ref. No. EN 16585-1:2017 EEN 16585-1:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Symbols and abbreviations . 8 5 Requirements and assessment 8 5.1 General 8
14、 5.2 Standard and universal toilets, common parameters . 8 5.3 Standard toilet 9 5.4 Universal toilet 10 5.5 Baby nappy changing table . 18 5.6 Interface of the call for aid device 19 6 Assessment methodologies 19 6.1 Lateral or side approach 19 6.2 Frontal or Diagonal approach 21 Annex A (normative
15、) Engineering limits for a wheelchair transportable by train . 24 A.1 Engineering limits 24 A.2 Characteristics 24 Annex B (normative) Simplified wheelchair profile and occupants reach range 27 B.1 Wheelchair profiles . 27 Annex C (normative) EC verification 29 C.1 Interoperability constituents 29 C
16、.2 Subsystems . 30 Annex D (normative) Summary of testing requirements . 32 Annex E (informative) Wheelchair accessible toilet guidance and good practice . 33 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2008/57/EC . 37 Bibliograph
17、y . 40 DIN EN 16585-1:2017-05 EN 16585-1:2017 (E) 3 European foreword This document (EN 16585-1:2017) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This document supersedes CEN/TS 16635:2014. This European Standard shall be given
18、 the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the
19、subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 2008/57/EC.
20、For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bul
21、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switze
22、rland, Turkey and the United Kingdom. DIN EN 16585-1:2017-05 EN 16585-1:2017 (E) 4 Introduction This document is part of a suite of four Design for PRM use standards that have in total nine parts: EN 16584 is a standard that covers both infrastructure and rolling stock Railway applications Design fo
23、r PRM use - General requirements: Part 1: Contrast (EN 16584-1); Part 2: Information (EN 16584-2); Part 3: Optical and friction characteristics (EN 16584-3). EN 16585 is a standard that covers rolling stock - Railway applications - Design for PRM use - Equipment and components on board rolling stock
24、: Part 1: Toilets (EN 16585-1); Part 2: Elements for sitting, standing and moving (EN 16585-2); Part 3: Clearways and internal doors (EN 16585-3). EN 16586 is a standard that covers rolling stock Railway applications Design for PRM use - Accessibility of persons with reduced mobility to rolling stoc
25、k: Part 1: Steps for access and egress (EN 16586-1); Part 2: Boarding aids (EN 16586-2). EN 16587 is a standard that covers infrastructure Railway applications Design for PRM use - Requirements for obstacle free routes for infrastructure. These standards aim to clarify the requirements (with clear a
26、nd consistent terms and definitions) and to define the associated criteria and, where appropriate, methodologies to allow a clear pass/fail assessment. DIN EN 16585-1:2017-05 EN 16585-1:2017 (E) 5 1 Scope This European Standard describes the specific Design for PRM use requirements applying to rolli
27、ng stock and the assessment of those requirements. The following applies to this standard: the definitions and requirements describe specific aspects of Design for PRM use required by persons with disabilities and persons with reduced mobility as defined in the PRM TSI; this standard defines element
28、s which are universally valid for obstacle free travelling including toilets, elements for sitting, standing and moving and clearways and internal doors. The definitions and requirements of this standard are to be used for rolling stock applications; this standard only refers to aspects of accessibi
29、lity for PRM passengers. It does not define general requirements and general definitions; this standard assumes that the rolling stock is in its defined operating condition; where minimum or maximum dimensions are quoted these are absolute NOT nominal requirements. The Equipment and Components stand
30、ard is written in three parts: this document is Part 1 and contains: toilets; part 2 contains: handholds; seats; wheelchair spaces; part 3 contains: clearways; internal doors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are ind
31、ispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12183, Manual wheelchairs - Requirements and test methods EN 12221-1:2008+A1:2013, Child use and care art
32、icles - Changing units for domestic use - Part 1: Safety requirements EN 12221-2:2008+A1:2013, Child use and care articles - Changing units for domestic use - Part 2: Test methods EN 12790, Child use and care articles - Reclined cradles DIN EN 16585-1:2017-05 N1)National footnote: The term “rolling
33、stock” is translated by Fahrzeuge in the German version. “Rolling stock” is based on TSI PRM, a specification for the application of TSIs for interoperability relating to accessibility of the European Unions rail system for persons with disabilities and persons with reduced mobility. N1)EN 16585-1:2
34、017 (E) 6 EN 16584-1, Railway applications - Design for PRM use - General requirements - Part 1: Contrast EN 16584-2:2017, Railway applications - Design for PRM use - General requirements - Part 2: Information EN 16585-2, Railway applications Design for PRM use Equipment and components on board roll
35、ing stock - Part 2: Elements for sitting, standing and moving EN 16585-3, Railway applications Design for PRM use Equipment and components on board rolling stock Part 3: Clearways and internal doors 3 Terms and definitions For the purposes of this document, the following terms and definitions apply.
36、 3.1 clear width clear usable width unobstructed width of an open door or clearway to allow passengers to pass through 3.2 clearway unobstructed space with defined widths and heights to allow movement within a vehicle 3.3 first step step that is the first step for a passenger to use, to overcome a h
37、eight change Note 1 to entry: For the external access/egress steps this will normally be the step that is closest to the platform edge (it may be a fixed or a moveable step), therefore this is the first step when boarding and the last step when alighting. Note 2 to entry: In the context of steps for
38、 internal height changes (other than the external access/egress steps) this means the first usable step when ascending and the edge of the walking floor when descending. 3.4 handrail continuous element with round cross section for passengers to use to aid personal stability by gripping around 3.5 la
39、st step final step for an ascending passenger to use to overcome a height change, forming the edge of the walking floor 3.6 manual door unpowered door which the passenger has to physically open and/or close 3.7 palm operable operable by the palm or any part of the hand, not requiring fingers to be u
40、nclenched Note 1 to entry: The design need is that passengers with painful conditions, which affect their joints such as arthritis, may be unable to (and are likely to experience discomfort or pain if they do) exert any force with the tip of a single finger. Many may not be able to unclench their fi
41、ngers to do this or perform any pulling action. DIN EN 16585-1:2017-05 EN 16585-1:2017 (E) 7 3.8 proximity sensor sensor that can be used to control facilities without the control device being physically touched 3.9 sharp edge thin edge capable of cutting or an abrupt end or discontinuity of a surfa
42、ce which has the potential to injure a passenger in normal use 3.10 standard toilet toilet not designed to be accessible to a passenger in a wheelchair 3.11 universal toilet toilet designed to be used by all passengers including passengers in wheelchairs 3.12 usable width unobstructed width of an op
43、en door or passageway allowing for passengers to pass through 3.13 wheelchair wheeled personal mobility device Note 1 to entry: Wheelchair characteristics are defined in Annex A. 3.14 wheelchair accessible doorway closest doorway to the wheelchair space (and wheelchair accessible sleeping accommodat
44、ion, where fitted) 3.15 wheelchair space designated space in the passenger compartment for the wheelchair users and their wheelchairs Note 1 to entry: Space can be designed for two wheelchairs, one beside the other (dual). DIN EN 16585-1:2017-05 EN 16585-1:2017 (E) 8 4 Symbols and abbreviations Tabl
45、e 1 Abbreviations Abbreviation Designation EN European Standard (Euronorm) PRM Persons with disabilities and persons with reduced mobility TSI Technical Specification for Interoperability Table 2 Symbols Symbol Designation Unit %ile Percentile kg Weight kilogram mm Length millimetre N Force Newton m
46、easurement of angles Degree 5 Requirements and assessment 5.1 General 1) Assessment of the requirements identified in Clause 5 shall be according to Annex C and Annex D. Where additional assessment criteria apply, these will be identified against the relevant clause. 2) All dimensions in the figures
47、 are in millimetres (mm) unless otherwise stated. 3) When toilets are fitted in a train, a universal toilet shall be provided that is accessible from the wheelchair space and, if provided, the sleeping compartment. 4) The standard toilet shall be compliant with the requirements of 5.2 and 5.3. 5) Th
48、e universal toilet shall be compliant with the requirements of 5.2 and 5.4. 5.2 Standard and universal toilets, common parameters 1) The centre of any door handle, lock or door control device on the exterior or interior of the toilet compartment shall be located at a minimum of 800 mm and a maximum
49、of 1 100 mm above the toilet door threshold. Assessment: this shall be measured vertically above the door threshold. 2) A visual and tactile (or audible) indication shall be given inside and outside the toilet to indicate when a door has been locked. Assessment: tactile and audible information shall be according to EN 16584-2. Assessment: Indication inside the toilet shall b
