1、July 2011 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2
2、3.040.20; 23.040.45; 93.030!$sA“1805830www.din.deDDIN EN ISO 11296-1Plastics piping systems for renovation of underground non-pressuredrainage and sewerage networks Part 1: General (ISO 11296-1:2009)English translation of DIN EN ISO 11296-1:2011-07Kunststoff-Rohrleitungssysteme fr die Renovierung vo
3、n erdverlegten drucklosenEntwsserungsnetzen (Freispiegelleitungen) Teil 1: Allgemeines (ISO 11296-1:2009)Englische bersetzung von DIN EN ISO 11296-1:2011-07Systmes de canalisations en plastique pour la rnovation des rseaux dassainissemententerrs sans pression Partie 1: Gnralits (ISO 11296-1:2009)Tra
4、duction anglaise de DIN EN ISO 11296-1:2011-07SupersedesDIN EN 13566-1:2003-04www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.2107.11 DIN EN ISO 11296-1:2011-07 2 A comma is used as the decimal marker. National foreword This standa
5、rd has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, Working Group WG 12 “Rehabilitation of pipeline systems” in collaboration with Tech-nical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, Ne
6、therlands). The responsible German body involved in its preparation was the Normenausschuss Wasserwesen (Water Practice Standards Committee), Working Committee NA 119-05-37 AA Renovierung, Reparatur und Erneue-rung von Abwasserkanlen und -leitungen. The DIN Standard corresponding to the Internationa
7、l Standard referred to in this document is as follows: ISO 11295 DIN EN ISO 11295 Amendments This standard differs from DIN EN 13566-1:2003-04 as follows: a) the text of ISO 11296-1 has been adopted; b) the scheme for the assessment of conformity (former Annex A) has been deleted. Previous editions
8、DIN EN 13566-1: 2003-04 National Annex NA (informative) Bibliography DIN EN ISO 11295, Classification and information on design of plastics piping systems used for renovation EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11296-1 April 2011 ICS 23.040.20; 23.040.45; 93.030; 91.140.80 Super
9、sedes EN 13566-1:2002English Version Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2009) Systmes de canalisations en plastique pour la rnovation des rseaux dassainissement enterrs sans pression - Partie 1: Gnralits (I
10、SO 11296-1:2009) Kunststoff-Rohrleitungssysteme fr die Renovierung von erdverlegten drucklosen Entwsserungsnetzen (Freispiegelleitungen) - Teil 1: Allgemeines (ISO 11296-1:2009) This European Standard was approved by CEN on 8 April 2011. CEN members are bound to comply with the CEN/CENELEC Internal
11、Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
12、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official version
13、s. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove
14、nia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN na
15、tional Members. Ref. No. EN ISO 11296-1:2011: EContents Page 1 Scope 7 2 Normative references 7 3 Terms and definitions .7 3.1 General terms.7 3.2 Techniques.9 3.3 Characteristics.10 3.4 Origin of materials .11 3.5 Product stages.12 4 Symbols and abbreviated terms 12 4.1 Symbols 12 4.2 Abbreviated t
16、erms .12 5 Pipes at the “M” stage.13 5.1 Materials .13 5.2 General characteristics .13 5.3 Material characteristics.13 5.4 Geometric characteristics.13 5.5 Mechanical characteristics .13 5.6 Physical characteristics13 5.7 Jointing .13 5.8 Marking .13 6 Fittings at the “M” stage .14 6.1 Materials .14
17、 6.2 General characteristics .14 6.3 Material characteristics.14 6.4 Geometric characteristics.14 6.5 Mechanical characteristics .14 6.6 Physical characteristics14 6.7 Jointing .14 6.8 Marking .14 7 Ancillary components .15 8 Fitness for purpose of the installed lining system at the “I” stage15 8.1
18、Materials .15 8.2 General characteristics .15 8.3 Material characteristics.15 8.4 Geometric characteristics.15 8.5 Mechanical characteristics .16 8.6 Physical characteristics16 8.7 Additional characteristics.16 8.8 Sampling.16 9 Installation practice .16 9.1 Preparatory work .16 9.2 Storage, handlin
19、g and transport of pipe and fittings.16 9.3 Equipment 16 9.4 Installation 17 9.5 Process-related inspection and testing 18 DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 2 Foreword Introduction .5 49.6 Lining termination .18 9.7 Reconnection to existing manholes and laterals.18 9.8 Final inspect
20、ion and testing.18 9.9 Documentation 18 Bibliography19 DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 3 Foreword The text of ISO 11296-1:2009 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization fo
21、r Standardization (ISO) and has been taken over as EN ISO 11296-1:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identic
22、al text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held re
23、sponsible for identifying any or all such patent rights. This document supersedes EN 13566-1:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cy
24、prus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO
25、11296-1:2009 has been approved by CEN as a EN ISO 11296-1:2011 without any modification. DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 4 Introduction The System Standard, of which this is part 1, specifies the requirements for plastics piping systems of various materials used for the renovation
26、 of existing pipelines in a specified application area. System Standards for renovation specify procedures for the following applications: plastics piping systems for renovation of underground non-pressure drainage and sewerage networks; plastics piping systems for renovation of underground drainage
27、 and sewerage networks under pressure; plastics piping systems for renovation of underground water supply networks; plastics piping systems for renovation of underground gas supply networks. These System Standards are distinguished from those for conventionally installed plastics piping systems beca
28、use they set requirements for certain characteristics in the as-installed condition, after site processing. This is in addition to specifying requirements for system components, as manufactured. Each of the System Standards comprises a part 1 (general) and all applicable renovation technique family-
29、related parts from the following: part 2: lining with continuous pipes; part 3: lining with close-fit pipes; part 4: lining with cured-in-place pipes; part 5: lining with discrete pipes; part 7: lining with spirally-wound pipes. The requirements for any given renovation technique family are given in
30、 part 1, applied in conjunction with the other relevant part. For example, parts 1 and 2 specify the requirements relating to lining with continuous pipes. For complementary information, see ISO 11295. Not all technique families are applicable to every area of application and this is reflected in th
31、e part numbers included in each System Standard. A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons across renovation technique families. Figure 1 gives the common structure and the relationship between ISO 11296 and the System Standards for oth
32、er application areas. DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 5 Figure 1 Format of the renovation System Standards DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 6 1 Scope This part of ISO 11296 specifies the requirements and test methods for plastics piping systems intended to be use
33、d for the renovation of underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar1). It is applicable to pipes and fittings as manufactured, as well as to the installed plastics lining system; it is not app
34、licable to the existing pipeline or any annular filler. This part of ISO 11296 establishes the general requirements common to all relevant renovation techniques (see 3.1.2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated re
35、ferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1610:1997, Construction and testing of drains and sewers EN 13508-2, Conditions of drain and sewer systems outside buildings Part 2: Visual inspectio
36、n coding system 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 General terms 3.1.1 pipeline system interconnecting pipe network for the conveyance of fluids 3.1.2 rehabilitation all measures for restoring or upgrading the performance of an e
37、xisting pipeline system DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 7 1) 1 bar = 0,1 MPa = 0,1 N/mm2= 105N/m2. 3.1.3 renovation work incorporating all or part of the original fabric of the pipeline by means of which its performance is improved 3.1.4 replacement rehabilitation of an existing p
38、ipeline system by the installation of a new pipeline system, without incorporating the original fabric 3.1.5 maintenance keeping an existing pipeline system operational without the installation of additional fabric 3.1.6 repair rectification of local damage 3.1.7 lining pipe pipe inserted for renova
39、tion purposes 3.1.8 liner lining pipe after installation 3.1.9 lining system lining pipe and all relevant fittings for insertion into an existing pipeline for the purposes of renovation 3.1.10 renovated pipeline system existing pipeline system plus the installed lining system used to renovate it, al
40、ong with any grout or other annular filling material used 3.1.11 characteristic property, dimension or other feature of a material or component 3.1.12 declared value limiting value of a characteristic declared in advance by the lining system supplier, which becomes the requirement for the purposes o
41、f assessment of conformity 3.1.13 annular filler material for grouting annular space between existing pipeline and the lining system 3.1.14 grouting process of filling voids around the lining system 3.1.15 simulated installation installation of a lining system into a simulated host pipeline, using r
42、epresentative equipment and processes, in order to provide samples for testing which are representative of an actual installation DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 8 3.1.16 simulated host pipeline section of pipeline, which is not part of an operational network, but which replicates
43、 the environment of an operational network 3.1.17 technique family group of renovation techniques which are considered to have common characteristics for standardization purposes 3.2 Techniques The various techniques for renovation of underground non-pressure drainage and sewerage networks, within t
44、he scope of pipeline rehabilitation techniques generally, are shown schematically in Figure 2. For definitions of standardized renovation techniques given in Figure 2, but outside the scope of this part of ISO 11296, see ISO 11295. This part of ISO 11296 is applicable to the following technique fami
45、lies. 3.2.1 lining with continuous pipes lining with pipe made continuous prior to insertion, and which has not been shaped to give it a cross-sectional diameter smaller than its final diameter after installation 3.2.2 lining with close-fit pipes lining with a continuous pipe for which the cross-sec
46、tion is reduced to facilitate installation and reverted after installation to provide a close fit to the existing pipe NOTE There are two options for achieving the reduction in cross-section: a) reduction in the pipe manufacturing plant; the pipe is usually supplied coiled on a reel from which it is
47、 directly inserted; b) reduction on site; the pipe is usually fed through the reduction equipment and simultaneously inserted in one continuous string. 3.2.3 lining with cured-in-place pipes lining with a flexible tube impregnated with a thermosetting resin, which produces a pipe after resin cure 3.
48、2.4 lining with discrete pipes lining with pipes shorter than the section to be renovated, which are jointed to form a continuous pipe only during insertion, the cross-section of the lining pipe remaining unchanged 3.2.5 lining with spirally-wound pipes lining with a profiled strip, spirally wound t
49、o form a continuous pipe after installation DIN EN ISO 11296-1:2011-07 EN ISO 11296-1:2011 (E) 9 aThis part of ISO 11296 applies. Figure 2 Technique families for renovation of underground non-pressure drainage and sewerage networks using plastics pipes, within the scope of pipeline rehabilitation techniques 3.3 Characteristics 3.3.1 nominal size numerical designation of the size of a component, which is a convenient round number approximately equal to the manufacturing dimension in millimetres 3.3.2 nominal size DN/OD nominal size
