1、March 2011 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、23.040.01!$nI“1753804www.din.deDDIN EN ISO 15877-2Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 2: Pipes (ISO 15877-2:2009 + AMD 1:2010)English translation of DIN EN ISO 15877-2:2011-03Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwa
3、sserinstallation Chloriertes Polyvinylchlorid (PVC-C) Teil 2: Rohre (ISO 15877-2:2009 + AMD 1:2010)Englische bersetzung von DIN EN ISO 15877-2:2011-03Systmes de canalisations en plastique pour les installations deau chaude et froide Poly(chlorure de vinyle) chlor (PVC-C) Partie 2: Tubes (ISO 15877-2
4、:2009 + AMD 1:2010)Traduction anglaise de DIN EN ISO 15877-2:2011-03SupersedesDIN EN ISO 15877-2:2009-07www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.2403.11 DIN EN ISO 15877-2:2011-03 2 A comma is used as the decimal marker. Nat
5、ional foreword This standard has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, Netherlands), Working Group WG 16 “Systems for hot and cold water applications” (lead-management: SIS, Sweden) in collaboration with ISO/TC 138 “Plastics
6、pipes, fittings and valves for the transport of fluids”, Subcommittee SC 2 “Plastics pipes and fittings for water supplies” (Secretariat: SNV, Switzerland). The responsible German body involved in its preparation was the Normenausschuss Wasserwesen (Water Practice Standards Committee), Working Commi
7、ttee NA 119-04-06-05 GUA Kunststoffrohre in der Trink-wasserversorgung; Warm- und Kaltwasserleitungen. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. The DIN Standards corresponding to the International Standards referred to in this document are
8、as follows, whereby EN ISO Standards are only listed below if these have not been published as DIN EN ISO Standards with the same number: ISO 1167-1 DIN EN ISO 1167-1 ISO 1167-2 DIN EN ISO 1167-2 ISO 2505 DIN EN ISO 2505 ISO 3126 DIN EN ISO 3126 ISO 6259-1 DIN EN ISO 6259-1 ISO 7686 DIN EN ISO 7686
9、ISO 9080 DIN EN ISO 9080 ISO 13760 DIN EN ISO 13760 ISO 15877-1 DIN EN ISO 15877-1 ISO 15877-3 DIN EN ISO 15877-3 ISO 15877-5 DIN EN ISO 15877-5 ISO/TS 15877-7 DIN ISO/TS 15877-7 Amendments This standard differs from DIN EN ISO 15877-2:2009-07 as follows: a) the scope has been extended to include ch
10、lorinated poly(vinyl chloride) (PVC-C) piping systems, Type I, on underfloor heatings and low temperature radiators (Application Class 4 according to ISO 10508) for design pressures of 4 bar and 6 bar. Previous editions DIN EN ISO 15877-2: 2004-03, 2009-07 DIN EN ISO 15877-2:2011-03 3 National Annex
11、 NA (informative) Bibliography DIN EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method DIN EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Deter
12、mination of the resistance to internal pressure Part 2: Preparation of pipe test pieces DIN EN ISO 2505, Thermoplastics pipes Longitudinal reversion Test methods and parameters DIN EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions DIN EN ISO 6259-1, Thermoplastics
13、pipes Determination of tensile properties Part 1: General test method DIN EN ISO 7686, Plastics pipes and fittings Determination of opacity DIN EN ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolati
14、on DIN EN ISO 13760, Plastics pipes for the conveyance of fluids under pressure Miners rule Calculation method for cumulative damage DIN EN ISO 15877-1, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 1: General DIN EN ISO 15877-3, Plastics
15、piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings DIN EN ISO 15877-5, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system DIN ISO/TS 15877-7, Plasti
16、cs piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 7: Guidance for the assessment of conformity DIN EN ISO 15877-2:2011-03 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15877-2 March 2009 November 2010 IC
17、S 23.040.20; 91.140.60 Supersedes EN ISO 15877-2:2003English version Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 2: Pipes (ISO 15877-2:2009 + AMD 1:2010) Systmes de canalisations en plastique pour les installations deau chaude et froide
18、Poly(chlorure de vinyle) chlor (PVC-C) Partie 2: Tubes (ISO 15877-2:2009 + AMD 1:2010) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation Chloriertes Polyvinylchlorid (PVC-C) Teil 2: Rohre (ISO 15877-2:2009 + AMD 1:2010) EN ISO 15877-2:2009-03 was approved by CEN on 2009-02-28 an
19、d Amendment A1:2010 on 2010-10-31. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati
20、onal standards may be obtained on application to the Management Centre or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notif
21、ied to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg
22、, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of
23、exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15877-2:2009 + A1:2010 E+ A1 Contents 2 DIN EN ISO 15877-2:2011-03 EN ISO 15877-2:2009 + A1:2010 (E) Page Foreword to EN ISO 15877-2:2009 3 !Foreword to EN ISO 15877-2:2009/A1:2010 4 Introduction .
24、5 1 Scope 6 2 Normative references 6 3 Terms, definitions and symbols.7 4 Material .7 4.1 General7 4.2 Pipe material.7 4.3 Evaluation of LPL-values7 4.4 Influence on water intended for human consumption.11 5 General characteristics .11 5.1 Appearance 11 5.2 Chamfering .11 5.3 Opacity11 6 Geometrical
25、 characteristics11 6.1 General11 6.2 Dimensions of pipes12 6.3 Wall thicknesses and their tolerances.12 7 Mechanical characteristics .13 7.1 Resistance to internal pressure .13 7.2 Impact resistance.14 7.3 Tensile strength .15 8 Physical characteristics15 9 Performance requirements .16 10 Adhesives
26、.16 11 Marking .17 11.1 General17 11.2 Minimum required marking.17 11.3 Additional marking 17 Annex A (informative) Derivation of the maximum calculated pipe value, Scalc,max.18 Bibliography 20 3Foreword to EN ISO 15877-2:2009 This document (EN ISO 15877-2:2009) has been prepared by Technical Commit
27、tee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”. This European Standard shall be given the status of a national standard, eith
28、er by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN
29、and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15877-2:2003. This part of ISO 15877 is part of a System Standard for plastics piping systems of a particular material for a specified application. There are a number of such S
30、ystem Standards. The System Standards are consistent with general standards on functional requirements and recommended practices for installation. This second edition cancels and replaces the first edition (ISO 15877-1:2003). ISO 15877 consists of the following parts1), under the general title Plast
31、ics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity Technical Specification At the date of publication of this part
32、 of ISO 15877, System Standards Series for piping systems of other plastics materials used for the same application are the following: ISO 15874 (all parts), Plastics piping systems for hot and cold water installations Polypropylene (PP) ISO 15875 (all parts), Plastics piping systems for hot and col
33、d water installations Crosslinked polyethylene (PE-X) ISO 15876 (all parts), Plastics piping systems for hot and cold water installations Polybutylene (PB) ISO 22391:2)(all parts), Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Acco
34、rding to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv
35、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. 1) This System Standard does not incorporate a Part 4: Ancillary equipment or a Part 6: Guidance for installation. For ancillary equipment, separat
36、e standards can apply. Guidance for installation of plastics piping systems made from different materials, intended to be used for hot and cold water installations, is covered by ENV 12108 3. 2)To be published. (Revisions of ISO 22391-1:2007, ISO 22391-2:2007, ISO 22391-3:2007, ISO 22391-5:2007.) DI
37、N EN ISO 15877-2:2011-03 EN ISO 15877-2:2009 + A1:2010 (E) 4 !Foreword to EN ISO 15877-2:2009/A1:2010 This document (EN ISO 15877-2:2009/A1:2010) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN, in collaboratio
38、n with Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”. This Amendment to the European Standard EN ISO 15877-2:2009 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 20
39、11, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. A
40、ccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
41、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.“ DIN EN ISO 15877-2:2011-03 EN ISO 15877-2:2009 + A1:2010 (E) 5Introduction The System Standard, of which this is Part 2, specifies the
42、 requirements for a piping system when made from chlorinated poly(vinyl chloride) (PVC-C). The piping system is intended to be used for hot and cold water installations and for heating system installations. In respect of potential adverse effects on the quality of water intended for human consumptio
43、n caused by the product covered by this part of ISO 15877, the following are relevant. a) This part of ISO 15877 provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. b) It should be noted that, while awaiting the adoption of
44、 verifiable European criteria, existing national regulations concerning the use and/or the characteristics of this product remain in force. When using solvent cement, relevant national safety rules or regulations concerning their use (e.g. protection of workers) are to be observed. Requirements and
45、test methods for material and components other than pipes are specified in ISO 15877-1 and ISO 15877-3. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 15877-5. ISO/TS 15877-7 gives guidance for the assessment of conformity. This part of ISO 15877 specifies the charact
46、eristics of pipes. DIN EN ISO 15877-2:2011-03 EN ISO 15877-2:2009 + A1:2010 (E) 6 1 Scope This part of ISO 15877 specifies the requirements of pipes made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the
47、 conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 15877-1:2009). This part of ISO 15877 covers a range of service conditions (application
48、classes), design pressures and pipe series. For values of TD, Tmaxand Tmalin excess of those in Table 1 of ISO 15877-1:2009, this part of ISO 15877 does not apply. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account t
49、heir particular requirements and any relevant national regulations and installation practices or codes. It also specifies the test parameters for the test methods referred to in this part of ISO 15877. In conjunction with the other parts of ISO 15877, it is applicable to PVC-C pipes, their joints and joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations. 2 Normative references The following
