DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf

上传人:赵齐羽 文档编号:680852 上传时间:2018-12-26 格式:PDF 页数:14 大小:850.08KB
下载 相关 举报
DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf_第1页
第1页 / 共14页
DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf_第2页
第2页 / 共14页
DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf_第3页
第3页 / 共14页
DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf_第4页
第4页 / 共14页
DIN EN ISO 294-4-2003 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4 Determination of moulding shrinkage (ISO 294-4 2001) German version EN ISO.pdf_第5页
第5页 / 共14页
点击查看更多>>
资源描述

1、ICS 83.080.20Kunststoffe Spritzgieen von Probekrpern aus Thermoplasten Teil 4: Bestimmung der Verarbeitungsschwindung (ISO 294-4 : 2001)European Standard EN ISO 294-4 : 2003 has the status of a DIN Standard.A comma is used as the decimal marker.National forewordThis standard has been published in ac

2、cordance with a decision taken by CEN/TC 249 to adopt, withoutalteration, International Standard ISO 294-4 as a European Standard.The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (PlasticsStandards Committee), Technical Committee Mechanische Eigenschaften u

3、nd Probekrperherstellung.DIN EN ISO 294-1 and DIN EN ISO 294-3 are the standards corresponding to International StandardsISO 294-1 and ISO 294-3, respectively, referred to in clause 2 of the EN.AmendmentsThis standard differs from the October 1998 edition in that it has been editorially revised and

4、details of lengthmeasurement have been changed.Previous editionDIN ISO 294-4: 1998-10.National Annex NAStandards referred to(and not included in Normative references, Bibliography and Annex ZA)DIN EN ISO 294-1 Plastics Injection moulding of test specimens of thermoplastic materials Part 1:General pr

5、inciples, and moulding of multipurpose and bar test specimens(ISO 294-1 : 1996)DIN EN ISO 294-3 Plastics Injection moulding of test specimens of thermoplastic materials Part 3:Small plates (ISO 294-3 : 1996)DIN EN ISO 294-4 : 2003-06English price group 09 Sales No. 110910.03DEUTSCHE NORM June 2003EN

6、 ISO 294-4Continued overleaf.EN comprises 12 pages. No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).PlasticsInjection

7、moulding of test specimens of thermoplastic materialsPart 4: Determination of moulding shrinkage (ISO 294-4 : 2001)English version of DIN EN ISO 294-4SupersedesOctober 1998 edition.English versionICS 83.080.20 Supersedes EN ISO 294-4 : 1998.Management Centre: rue de Stassart 36, B-1050 BrusselsEurop

8、ean Committee for StandardizationComit Europen de NormalisationEuropisches Komitee fr NormungPlasticsInjection moulding of test specimens of thermoplastic materialsPart 4: Determination of moulding shrinkage(ISO 294-4 : 2001) 2003. CEN All rights of exploitation in any form and by any meansreserved

9、worldwide for CEN national members.Ref. No. EN ISO 294-4 : 2003 EPlastiques Moulage par injectiondes prouvettes de matriaux ther-moplastiques Partie 4: Dtermina-tion du retrait au moulage(ISO 294-4 : 2001)Kunststoffe Spritzgieen von Pro-bekrpern aus Thermoplasten Teil 4: Bestimmung der Verarbei-tung

10、sschwindung (ISO 294-4 : 2001)This European Standard was approved by CEN on 2002-12-27.CEN members are bound to comply with the CEN/CENELEC Internal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists an

11、d bibliographical references concerning such national stand-ards may be obtained on application to the Management Centre or to any CENmember.The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility

12、of aCEN member into its own language and notified to the Management Centre hasthe same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland,Ireland, Italy, Luxembourg, Malta,

13、the Netherlands, Norway, Portugal, Slovakia,Spain, Sweden, Switzerland, and the United Kingdom.EN ISO 294-4February 2003Page 2EN ISO 294-4 : 2003ForewordInternational StandardISO 294-4 : 2001 Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Deter-mination of moulding

14、shrinkage,which was prepared by ISO/TC 61 Plastics of the International Organization for Standardization, has beenadopted by Technical Committee CEN/TC 249 Plastics, the Secretariat of which is held by IBN, as a EuropeanStandard.This European Standard shall be given the status of a national standard

15、, either by publication of an identicaltext or by endorsement, and conflicting national standards withdrawn, by August 2003 at the latest.In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of the follow-ing countries are bound to implement this European Sta

16、ndard:Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,Italy, Luxembourg, Malta, the Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland, and theUnited Kingdom.Endorsement noticeThe text of the International Standard ISO 294-4

17、 : 2001 was approved by CEN as a European Standard withoutany modification.NOTE: Normative references to international publications are listed in Annex ZA (normative).Page 3EN ISO 294-4 : 200344566910101112Page 4EN ISO 294-4 : 2003Page 5EN ISO 294-4 : 2003Page 6EN ISO 294-4 : 2003Page 7EN ISO 294-4 : 2003Page 8EN ISO 294-4 : 2003Page 9EN ISO 294-4 : 2003Page 10EN ISO 294-4 : 2003Page 11EN ISO 294-4 : 2003Page 12EN ISO 294-4 : 2003

展开阅读全文
相关资源
  • DIN EN 818-7-2008 Short link chain for lifting purposes - Safety - Part 7 Fine tolerance hoist chain Grade T (Types T DAT and DT)(includes Amendment A1 2008) Ge.pdfDIN EN 818-7-2008 Short link chain for lifting purposes - Safety - Part 7 Fine tolerance hoist chain Grade T (Types T DAT and DT)(includes Amendment A1 2008) Ge.pdf
  • DIN EN 1677-3-2008 Components for slings - Safety - Part 3 Forged steel self-locking hooks Grade 8(includes Amendment A1 2008) English version of DIN EN 1677-3 .pdfDIN EN 1677-3-2008 Components for slings - Safety - Part 3 Forged steel self-locking hooks Grade 8(includes Amendment A1 2008) English version of DIN EN 1677-3 .pdf
  • DIN EN 1677-2-2008 Components for slings - Safety - Part 2 Forged steel lifting hooks with latch Grade 8(includes Amendment A1 2008) English version of DIN EN 1.pdfDIN EN 1677-2-2008 Components for slings - Safety - Part 2 Forged steel lifting hooks with latch Grade 8(includes Amendment A1 2008) English version of DIN EN 1.pdf
  • DIN EN 1670-2007 Building hardware - Corrosion resistance - Requirements and test methods English version of DIN EN 1670 2007-06《建筑五金器具 耐腐蚀 要求和试验方法》.pdfDIN EN 1670-2007 Building hardware - Corrosion resistance - Requirements and test methods English version of DIN EN 1670 2007-06《建筑五金器具 耐腐蚀 要求和试验方法》.pdf
  • DIN EN 1656-2010 Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and.pdfDIN EN 1656-2010 Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and.pdf
  • DIN EN 1230-2-2018 Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2 Off-flavour (taint) German version EN 1230-2 2009《用.pdfDIN EN 1230-2-2018 Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2 Off-flavour (taint) German version EN 1230-2 2009《用.pdf
  • DIN EN 1176-7-2008 Playground equipment and surfacing - Part 7 Guidance on installation inspection maintenance and operation English version of DIN EN 1176-7 20.pdfDIN EN 1176-7-2008 Playground equipment and surfacing - Part 7 Guidance on installation inspection maintenance and operation English version of DIN EN 1176-7 20.pdf
  • DIN EN 1176-5-2008 Playground equipment and surfacing - Part 5 Additional specific safety requirements and test methods for carousels English version of DIN EN .pdfDIN EN 1176-5-2008 Playground equipment and surfacing - Part 5 Additional specific safety requirements and test methods for carousels English version of DIN EN .pdf
  • DIN EN 1159-1-2007 Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1 Determination of thermal expansion (includes Corrigendu.pdfDIN EN 1159-1-2007 Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1 Determination of thermal expansion (includes Corrigendu.pdf
  • DIN EN 1093-4-2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4 Capture efficiency of an exhaust system - Tracer m.pdfDIN EN 1093-4-2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4 Capture efficiency of an exhaust system - Tracer m.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > DIN

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1