1、November 2014Translation by DIN-Sprachendienst.English price group 6No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、 25.120.10!%5“2270218www.din.deDDIN ISO 23481Tools for pressing Cam driver plates (ISO 23481:2013),English translation of DIN ISO 23481:2014-11Werkzeuge der Stanztechnik berlaufkeile (ISO 23481:2013),Englische bersetzung von DIN ISO 23481:2014-11Outillage de presse Plaques dentranement de came (ISO
3、23481:2013),Traduction anglaise de DIN ISO 23481:2014-11SupersedesDIN ISO 23481:2011-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 7 pages11.14 2DIN ISO 23481:2014-11A comma is used as the decimal marker. Contents Page National fore
4、word .3 National Annex NA (informative) Bibliography .4 1 Scope .5 2 Normative references .5 3 Dimensions .5 4 Material 7 5 Designation .7 National foreword The text of ISO 23481:2013 has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcom-mittee SC 8 “Tools for pressing and mouldin
5、g” on the lines of VDI 3357:2014-01. The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standards Committee Tools and Clamping Devices), Working Committee NA 121-03-02 AA Werkzeuge der Stanztechnik. ISO 23481:2013 has been adopted in thi
6、s standard without any modification. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. The DIN Standards corresponding to the International
7、Standards referred to in this document are as follows: ISO 2768-1 DIN ISO 2768-1 ISO 4762 DIN EN ISO 4762 ISO 13715 DIN ISO 13715 Amendments This standard differs from DIN ISO 23481:2011-03 as follows: a) Figure 2 has been technically revised to enlarge the radius R of the cam driver plate; b) the s
8、tandard has been editorially revised. Previous editions DIN ISO 23481: 2011-03 3DIN ISO 23481:2014-11National Annex NA (informative) Bibliography 4DIN ISO 23481:2014-11DIN EN ISO 4762, Hexagon socket head cap screws DIN ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensi
9、ons without individual tolerance indications DIN ISO 13715, Technical drawings Edges of undefined shape Vocabulary and indication on drawings VDI 3357, Sliding elements in large stamping dies 1 ScopeThis International Standard specifies the main dimensions and tolerances of plates to be used for cam
10、 drivers and slides in tools for pressing (an application example is shown in Figure 1).It also specifies the designation of cam driver plates.Figure 1 Application example of cam driver plates2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this docum
11、ent and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without in
12、dividual tolerance indicationsISO 4762, Hexagon socket head cap screwsISO 13715, Technical drawings Edges of undefined shape Vocabulary and indications3 DimensionsThe dimensions of cam driver plates shall conform to the indications in Figure 2 and Table 1.All edges of undefined shape shall be in acc
13、ordance with ISO 13715.Tools for pressing Cam driver plates5DIN ISO 23481:2014-11General tolerance: ISO 2768-mdimensions in millimetressurface roughness values in micrometresFigure 2 Cam driver plates6DIN ISO 23481:2014-11Table 1 Dimensions of cam driver platesDimensions in millimetresWb1020,l10,2T0
14、,01l2b2l3Hexagon socketISO 4762 pieces20100 170 45906045 M12 40 4125 170 45 85150 170 45 11030100150 45906045 M12 40 4170 60125150 4585170 60150150 45110170 604 MaterialThe choice of material is left to the manufacturers discretion.5 DesignationCam driver plates in accordance with this International
15、 Standard shall be designated by:a) Cam driver plate;b) a reference to this International Standard, i.e. ISO 23481;c) width, b1, in millimetres;d) length, l1, in millimetres;e) thickness, T, in millimetres.EXAMPLE A cam driver plate with width b1= 100 mm, length l1= 170 mm, and thickness T = 60 mm is designated as follows:Cam driver plate ISO 23481 - 100 170 607DIN ISO 23481:2014-11
