1、INCHPOUND AA55563/21A 21 January 2013 Superseding AA55563/21 19 November 2004 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, CLOSED ENDED, WITHOUT FLARED ENTRY, WITH THREE MOUNTING HOLES, FOR VERSAMODULE EUROCARD APPLICATIONS The General Servi
2、ces Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring metal card holders described herein shall consist of this document and the latest issue in effect of commercial item description (CID) AA55563. CLASSIFICATI
3、ON/PART IDENTIFICATION NUMBER (PIN). This CID specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA55563 CID number /21 Applicable CID sheet Material # Card holder width/board thickness $ $
4、Length AA55563/21#$ AA55563/21#$& 1/ Manufacturers 2/ Material type Card holder width/board thickness (see table I) Overall length designator (see table II) Finish 3/ CAGE 18915 4/ B # 10 & 35C8BHT2P B # 15 & 35C8BHT3P B # 20 & 35C8BHT4P B # 25 & 35C8BHT5P B # 30 & 35C8BHT6P B # 35 & 35C8BHT7P B # 4
5、0 & 35C8BHT8P B # 45 & 35C8BHT9P B # 50 & 35C8BHT10P B # 55 & 35C8BHT11P B # 60 & 35C8BHT12P D # 10 & 35C8CRT2 D # 15 & 35C8CRT3 D # 20 G 35C8CRT4 D # 25 G 35C8CRT5 D # 30 G 35C8CRT6 D # 35 G 35C8CRT8 D # 40 G 35C8CRT8 D # 45 G 35C8CRT9 D # 50 G 35C8CRT10 D # 55 G 35C8CRT11 D # 60 G 35C8CRT12 1/ The
6、 at sign () denotes material type, pound sign (#) denotes card holder width/board thickness (see dimension “T“ on figure 1 herein), dollar signs ($) denotes overall length (see dimension “L“ on figure 1 herein and AA55563), and the ampersand (&) denotes finish. 2/ The manufacturers part number shall
7、 not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ F
8、inish materials designator “H“, “K“, “C“, “D“, “E“, “F“, “R“, or “J“ are available for this material type. 4/ Manufacturer CAGE 18915 superseded part number is constructed as follows: The series type is “35C8“, the letter “T“ denotes card holder width/board thickness, the numbers “2“ through “12“ de
9、notes card holder lengths, and the letter “P“ denotes finish material. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/21A 6 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where chang
10、es from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the ma
11、rginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982012037 Review activity: Air Force 99 NOTE: The activities listed above were interested
12、 in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
