1、INCHPOUND AA59590/3D 3 May 2013 SUPERSEDING AA59590/3C 3 October 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .225 X .260 INCH BODY SIZE, WITH VISUAL LOCK INDICATION The General Services Administration has authorized th
2、e use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item desc
3、ription (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /03 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) W, D, E Configuration (see ta
4、ble II) Example: AA59590/03EK63 is the PIN for a nickel finished, 6.3 inch (160.0 mm) long card holder with a retained actuating screw. The card holder also has three counterbored through holes for use with rivet fasteners. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit ca
5、rd assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 Grms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and the heat sink surfaces. Material
6、. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, 4, in table I, and AA59590. Visual lock indicator (see figure 2). Ca
7、rd holders shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the unlocked (relaxed) state, the actuating end of the screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been ti
8、ghtened (assembly expanded) so that the assembly is in the locked position, this red band shall be concealed. Actuating screw hex drive socket. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“ and
9、2.5 mm (0.098 inch) for mounting options “G“ and “M“. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 6 inch-pounds (0.68 N-m) for assemblies using no options or option “W“ and 7.2 inch-pound
10、s (0.81 N-m) for assemblies using options “E“ or “D“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/3D 2 Inches mm Inches mm Inches mm Inches mm Inches mm .20 .225 5.1 5.7 .240 .25 6.1 6.4 .270 .325 6.9 8.3 .33 .50 8.4 12.7
11、 .70 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Dimension shall be .20 inch (5.1 mm) maximum on card holders w
12、ithout option “W“ or “D“ and .30 inch (7.6 mm) maximum on card holders with option “W“ or “D“. 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“. The across flats dimension for hex drive socket shall be a metric
13、 dimension of 2.5 mm (.098 inch) across flats for mounting options “G“ and “M“ FIGURE 1. Relaxed and expanded dimensions. FIGURE 2 Visual lock indicator. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/3D 3 TABLE I. Additional assembly dimens
14、ions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) Without options “W“ or “D“ With options “W“ or “D“ 18 1.8 (45.7) 2.00 (50.8) 2.10 (53.3) 1.30 (33.0) .75 (19.1) 23 2.3 (58.4) 2.50 (63.5) 2.60 (66.0) 1
15、.80 (45.7) .40 (10.2) 28 2.8 (71.1) 3.00 (76.2) 3.10 (78.7) 2.30 (58.4) .90 (22.9) 30 3.0 (76.2) 3.20 (81.3) 3.30 (83.8) 2.50 (63.5) 1.10 (27.9) 33 3.3 (83.8) 3.50 (88.9) 3.60 (91.4) 2.80 (71.1) 1.40 (35.6) 35 3.5 (88.9) 3.70 (94.0) 3.80 (96.5) 3.00 (76.2) 1.60 (40.6) 38 3.8 (96.5) 4.00 (101.6) 4.10
16、 (104.1) 3.30 (83.8) 1.90 (48.3) 43 4.3 (109.2) 4.50 (114.3) 4.60 (116.8) 3.80 (96.5) 2.40 (61.0) 48 4.8 (121.9) 5.00 (127.0) 5.10 (129.1) 4.30 (109.2) 2.90 (73.7) 53 5.3 (134.6) 5.50 (139.7) 5.60 (142.2) 4.80 (121.9) 3.40 (86.4) 55 5.5 (139.7) 5.70 (144.8) 5.80 (147.3) 5.00 (127.0) 3.60 (91.4) 58 5
17、.8 (147.3) 6.00 (152.4) 6.10 (154.9) 5.30 (134.6) 3.90 (99.1) 61 6.1 (154.9) 6.30 (160.0) 6.40 (162.6) 5.60 (142.2) 4.20 (106.7) 63 6.3 (160.0) 6.50 (165.1) 6.60 (167.6) 5.80 (147.3) 4.40 (111.8) 67 6.7 (170.2) 6.90 (175.3) 7.00 (177.8) 6.20 (157.5) 4.80 (121.9) 1/ Dimensions are in inches. Millimet
18、ers, in parenthesis, are given for general information only. Cold plate slot width dimensions. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA595
19、90). Finish. The finish designator shall be as specified in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), and “R“ (clear chemical film). Mounting options.
20、The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ or “K“ (rivet mounting holes), “N“ (no mounting holes), “R“ or “T“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.
21、5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. See figure 1 and table I for mounting hole spacing requirements. Mounting holes (when required). Two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes a
22、re required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .066 to .073 inch (
23、1.68 to 1.85 mm) diameter through holes, countersunk 100 degrees by .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA
24、59590/3D 4 Rivets. This card holder uses rivet style A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the availab
25、le lengths for this specification sheet are listed in table I. Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1, 2, 3,and 4. Card holders not requiring the options described by table II shall
26、leave the configuration position in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardware options - 1 and 2 No added options W 1, 2, and 3 Lockwasher and flat washer E 1, 2, and 4 Screw self-locking element D 1, 2, 3, and 4 Lockwasher, flat washer and screw self-locking
27、element Lockwasher and flat washer (see figure 3). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix
28、 “W“ in the PIN (see classification and notes). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The use of a screw self-locking element on the screw will provide prevailing torque for increased resistance to loosening of the card holder assembly from shock an
29、d vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking element shall include a configuration suffix “E“ in the PIN (see classification and notes). FIGURE 4. Screw self-locking element details. Provided by IHSNot for ResaleNo reproduc
30、tion or networking permitted without license from IHS-,-,-AA59590/3D 5 Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a configuration suffix “D“ in the PIN (see classification and notes).
31、NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Dri
32、ve, General Requirements For. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA5
33、9590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial
34、products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact in
35、formation 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephon
36、e: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ 3E7U8 Wakefield Solutions 200 Towerview Cour
37、t Cary, NC 27513 Telephone: (919) 4692004 Facsimile: (919) 4692827 E-mail: URL: Part number supersession data. This CID specification sheet part numbers supersede the following manufacturers part numbers in table III and on DESC Drawing 84103 (table IV) as shown. The CID PINs listed in table III a
38、re only for length designator “28“. See table V for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking p
39、ermitted without license from IHS-,-,-AA59590/3D 6 TABLE III. Commercial part number supersession data. PIN designator AA59590/03 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7U8 BJ28 40VI6B VA225CR2.80H 3225VBA2.80H 426B280RSBV BN28 40VI6BA VA225CR2.80
40、 3225VBA2.80 426B280ASBV BT28 40VI6BT VA225CR2.80T0 3225VBA2.80T0 426B280TSBV BV28 40VI6BS VA225CR2.80T2 3225VBA2.80T2 426B280SSBV BG28 40VI6BM MVA225CR2.80TM2.5 3225MVBA2.80TM2.5 426B280MMBV BJ28E 40VI6BL VA225CR2.80HL 3225VBA2.80HL 426B280RSBPV BN28E 40VI6BAL VA225CR2.80L 3225VBA2.80L 426B280ASBPV
41、 BT28E 40VI6BTL VA225CR2.80T0L 3225VBA2.80T0L 426B280TSBPV BV28E 40VI6BSL VA225CR2.80T2L 3225VVBA2.80T2L 426B280SSBPV BG28E 40VI6BML MVA225CR2.80TM2.5L 3225MVBA2.80TM2.5L 426B280MMBPV BJ28W 40VI6BLF WVA225CR2.80H 3225VWBA2.80H 426B280RSBWV BN28W 40VI6BLFA WVA225CR2.80 3225VWBA2.80 426B280ASBWV BT28W
42、 40VI6BLFT WVA225CR2.80T0 3225VWBA2.80T0 426B280TSBWV BV28W 40VI6BLFS WVA225CR2.80T2 3225VWBA2.80T2 426B280SSBWV BG28W 40VI6BLFM MVWA225CR2.80TM2.5 3225MVWBA2.80TM2.5 426B280MMBWV BJ28D 40VI6BLFL WVA225CR2.80HL 3225VWBA2.80HL 426B280RSBWPV BN28D 40VI6BLFAL WVA225CR2.80L 3225VWBA2.80L 426B280ASBWPV B
43、T28D 40VI6BLFTL WVA225CR2.80T0L 3225VWBA2.80T0L 426B280TSBWPV BV28D 40VI6BLFSL WVA225CR2.80T2L 3225VWBA2.80T2L 426B280SSBWPV BG28D 40VI6BLFML MWVA225CR2.80TM2.5L 3225MVWBA2.80TM2.5L 426B280MMBWPV CJ28 40VI6 VA225CR2.80H 3225VBA2.80H 426B280RSGV CN28 40VI6A VA225CR2.80 3225VBA2.80 426B280ASGV CT28 40
44、VI6T VA225CR2.80T0 3225VBA2.80T0 426B280TSGV CV28 40VI6S VA225CR2.80T2 3225VBA2.80T2 426B280SSGV CG28 40VI6M MVA225CR2.80TM2.5 3225MVBA2.80TM2.5 426B280MMGV CJ28E 40VI6L V225CR2.80HL 3225VCG2.80HL 426B280RSGPV CN28E 40VI6AL V225CR2.80L 3225VCG2.80L 426B280ASGPV CT28E 40VI6TL V225CR2.80T0L 3225VCG2.8
45、0T0L 426B280TSGPV CV28E 40VI6SL V225CR2.80T2L 3225VCG2.80T2L 426B280SSGPV CG28E 40VI6ML MV225CR2.80TM2.5L 3225MVCG2.80TM2.5L 426B280MMGPV See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/3D 7 TABLE III. Commercial
46、 part number supersession data Continued. PIN designator AA59590/03 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7U8 CJ28W 40VI6LF WV225CR2.80H 3225VWCG2.80H 426B280RSGWV CN28W 40VI6LFA WV225CR2.80 3225VWCG2.80 426B280ASGWV CT28W 40VI6LFT WV225CR2.80T0
47、3225VWCG2.80T0 426B280TSGWV CV28W 40VI6LFS WV225CR2.80T2 3225VWCG2.80T2 426B280SSGWV CG28W 40VI6LFM MWV225CR2.80TM2.5 3225MVWCG2.80TM2.5 426B280MMGWV CJ28D 40VI6LFL WV225CR2.80HL 3225VWCG2.80HL 426B280RSGWPV CN28D 40VI6LFAL WV225CR2.80L 3225VWCG2.80L 426B280ASGWPV CT28D 40VI6LFTL WV225CR2.80T0L 3225VWCG2.80T0L 426B280TSGWPV CV28D 40VI6LFSL WV225CR2.80T2L 3225VWCG2.80T2L 426B280SSGWPV CG28D 40VI6LFML MWV225CR2.80TM2.5L 3225MVWCG2.80TM2.5L 426B280MMGWPV EJ28 40VI6EN
