1、INCHPOUND AA59590/5D 5 July 2013 SUPERSEDING AA59590/5C 5 October 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .225 X .260 INCH BODY SIZE, WITH SCREW RETENTION The General Services Administration has authorized the use
2、of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (
3、CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /05 Applicable CID specification sheet B, C, H, R Finish * Mounting * * Length (see table I) D, E, W Configuration (see ta
4、ble II) Example: AA59590/05HT18 is the PIN for a hard black anodize finished, 1.8 inch (45.7 mm) long card holder with a retained actuating screw. The card holder also has two tapped mounting holes for use with 080 UNF fasteners. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circ
5、uit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 G-rms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the circuit card assembly and the heat sink surfaces. M
6、aterial. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, 3, 4, in table I, table II, and AA59590. Actuating screw hex dri
7、ve socket. The across flats dimension for the hex drive socket shall be as follows: .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“ and .098 inch (2.5 mm) for mounting options “G“ and “M“. Cold plate slot width dimensions (when applicable). The recommend cold plate slo
8、t width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of
9、 each card holder shall be as follows: 6 inchpounds (0.68 Nm) for assemblies of the base configuration or configuration “W“ and 8 inchpounds (0.90 Nm) for assemblies of configurations “E“ or “D“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
10、rom IHS-,-,-AA59590/5D 2 Inches mm Inches mm Inches mm Inches mm .070 .225 1.78 5.72 .250 .25 6.35 6.35 .270 .30 6.86 7.6 .325 .70 8.26 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for tw
11、o place decimals and .010 inch (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm) for mounting options “J“, “K“, “N“, “T“, “R“, “V“, and “S“. The across flats dimension for hex drive socket shall be a hard metric dimension of .098 inch
12、 (2.5 mm) across flats for mounting options “G“ and “M“. 4. Dimension shall be .20 inch (5.1 mm) maximum on card holders of the base configuration or configuration “E“ and .30 inch (7.6 mm) maximum on card holders of configuration “W“ or “D“. FIGURE 1. Relaxed and expanded dimensions. Provided by IH
13、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/5D 3 Screw retention locknut (see figure 2). The card holders shall have a screw retention locknut intended to prevent unintentional disassembly of the card holder. The locknut shall be fabricated of a corros
14、ion resistant material. FIGURE 2. Screw retaining self-locking nut (corrosion resistant) details. TABLE I. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ +.02 / .09 (+0.5 / 2.3) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) With
15、out option “W“ or “D“ With option “W“ or “D“ 18 1.8 (45.7) 2.10 (53.3) 2.20 (55.9) 1.30 (33.0) .75 (19.1) 23 2.3 (58.4) 2.60 (66.0) 2.70 (68.6) 1.80 (45.7) .40 (10.2) 28 2.8 (71.1) 3.10 (78.7) 3.20 (81.3) 2.30 (58.4) .90 (22.9) 30 3.0 (76.2) 3.30 (83.8) 3.40 (86.4) 2.50 (63.5) 1.10 (27.9) 33 3.3 (83
16、.8) 3.60 (91.4) 3.70 (94.0) 2.80 (71.1) 1.40 (35.6) 35 3.5 (88.9) 3.80 (96.5) 3.90 (99.1) 3.00 (76.2) 1.60 (40.6) 38 3.8 (96.5) 4.10 (104.1) 4.20 (106.7) 3.30 (83.8) 1.90 (48.3) 43 4.3 (109.2) 4.60 (116.8) 4.70 (119.4) 3.80 (96.5) 2.40 (61.0) 48 4.8 (121.9) 5.10 (129.5) 5.20 (132.1) 4.30 (109.2) 2.9
17、0 (73.7) 53 5.3 (134.6) 5.60 (142.2) 5.70 (144.8) 4.80 (121.9) 3.40 (86.4) 55 5.5 (139.7) 5.80 (147.3) 5.90 (149.9) 5.00 (127.0) 3.60 (91.4) 58 5.8 (147.3) 6.10 (154.9) 6.20 (157.5) 5.30 (134.6) 3.90 (99.1) 61 6.1 (154.9) 6.40 (162.6) 6.50 (165.1) 5.60 (142.2) 4.20 (106.7) 63 6.3 (160.0) 6.60 (167.6
18、) 6.70 (170.2) 5.80 (147.3) 4.40 (111.8) 67 6.7 (170.2) 7.00 (177.8) 7.10 (180.3) 6.20 (157.5) 4.80 (121.9) 68 6.8 (172.7) 7.10 (180.3) 7.20 (182.9) 6.30 (160.0) 4.90 (124.5) 73 7.3 (185.4) 7.60 (193.0) 7.70 (195.6) 6.80 (172.7) 5.40 (137.2) 78 7.8 (198.1) 8.10 (205.7) 8.20 (208.3) 7.30 (185.4) 5.90
19、 (149.9) 83 8.3 (210.8) 8.60 (218.4) 8.70 (221.0) 7.80 (198.1) 6.40 (162.6) 88 8.8 (223.5) 9.10 (231.1) 9.20 (233.7) 8.30 (210.8) 6.90 (175.3) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking
20、permitted without license from IHS-,-,-AA59590/5D 4 Finish. The finish designator shall be as specified in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film)
21、. Mounting options. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ or “K“ (rivet mounting holes), “N“ (no mounting holes), “T“ or “R“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G
22、“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ or “K“ may be shipped unassembled. See figure 1 for mounting hole spacing requirements. Mounting holes and locations (when required). When not using mounting option “N“, mounting holes will be present in the center body
23、 (see figure 1). Two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting hole shall be centered on the mounting body. See figure 1 and table I for mou
24、nting hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .066 to .073 inch (1.68 to 1.85 mm) diameter through holes, countersunk 100 degrees by .140 inch (3.56 mm) diameter with an access/clearance counterbore hole of .156 inch (3.96 mm) diamete
25、r by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA5
26、9590 and the available lengths for this CID specification sheet are listed in table I. Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. Card ho
27、lders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardware options 1 and 2 No added options W 1, 2, and 3 Lockwasher and flat washer E 1, 2, and 4 Screw self-locking element D 1, 2
28、, 3, and 4 Lockwasher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 3). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration. Card holders req
29、uiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes herein). FIGURE 3. Lockwasher and flat washer details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/5D 5 Screw self-locking element (se
30、e figure 4). The use of a screw self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking
31、element shall include configuration identifier “E“ in the PIN (see classification and notes herein). FIGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration s
32、hall include a suffix “D“ in the PIN (see classification and notes herein). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description A
33、A59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelph
34、ia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet prep
35、aration and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers sho
36、wn.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/5D 6 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Tel
37、ephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 American Circuit
38、 Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ 3E7U8 Wakefield Solutions 200 Towerview Court Cary, NC 27513 Telephone: (919) 4692004 Facsimile: (919) 4692827 E-mail: URL: Part number supersession data.
39、This CID specification sheet PINs supersede the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is bein
40、g provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. PIN designator AA59590/05 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7UB BJ28 406BLN A225CR2.80HR 3225BA2.80HR 426B
41、280RSBA BN28 406BLNA A225CR2.80R 3225BA2.80R 426B280ASBA BT28 406BLNT A225CR2.80T0R 3225BA2.80T0R 426B280TSBA BV28 406BLNS A225CR2.80T2R 3225BA2.80T2R 426B280SSBA BG28 406BLNM MA225CR2.80TM2.5R 3225MBA2.80TM2.5R 426B280MMBA BJ28E 406BLNL A225CR2.80HLR 3225BA2.80HLR 426B280RSBAP BN28E 406BLNAL A225CR
42、2.80LR 3225BA2.80LR 426B280ASBAP BT28E 406BLNTL A225CR2.80T0LR 3225BA2.80T0LR 426B280TSBAP BV28E 406BLNSL A225CR2.80T2LR 3225BA2.80T2LR 426B280SSBAP BG28E 406BLNML MA225CR2.80TM2.5LR 3225MBA2.80TM2.5LR 426B280MMBAP See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networ
43、king permitted without license from IHS-,-,-AA59590/5D 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/05 Vendor similar designator or type part number 1/ 2/ CAGE 18915 CAGE 61081 CAGE 5BG68 CAGE 3E7UB BJ28W 406BLFLN WA225CR2.80HR 3225WBA2.80HR 426B280RSBWA BN
44、28W 406BLFLNA WA225CR2.80R 3225WBA2.80R 426B280ASBWA BT28W 406BLFLNT WA225CR2.80T0R 3225WBA2.80T0R 426B280TSBWA BV28W 406BLFLNS WA225CR2.80T2R 3225WBA2.80T2R 426B280SSBWA BG28W 406BLFLNM MWA225CR2.80TM2.5R 3225MWBA2.80TM2.5R 426B280MMBWA BJ28D 406BLFLNL WA225CR2.80HLR 3225WBA2.80HLR 426B280RSBWAP BN
45、28D 406BLFLNAL WA225CR2.80LR 3225WBA2.80LR 426B280ASBWAP BT28D 406BLFLNTL WA225CR2.80T0LR 3225WBA2.80T0LR 426B280TSBWAP BV28D 406BLFLNSL WA225CR2.80T2LR 3225WBA2.80T2LR 426B280SSBWAP BG28D 406BLFLNML MWA225CR2.80TM2.5LR 3225MWBA2.80TM2.5LR 426B280MMBWAP CJ28 406LN 225CR2.80HR 3225CG2.80HR 426B280RSG
46、A CN28 406LNA 225CR2.80R 3225CG2.80R 426B280ASGA CT28 406LNT 225CR2.80T0R 3225CG2.80T0R 426B280TSGA CV28 406LNS 225CR2.80T2R 3225CG2.80T2R 426B280SSGA CG28 406LNM M225CR2.80TM2.5R 3225MCG2.80TM2.5R 426B280MMGA CJ28E 406LNL 225CR2.80HLR 3225CG2.80HLR 426B280RSGAP CN28E 406LNAL 225CR2.80LR 3225CG2.80L
47、R 426B280ASGAP CT28E 406LNTL 225CR2.80T0LR 3225CG2.80T0LR 426B280TSGAP CV28E 406LNSL 225CR2.80T2LR 3225CG2.80T2LR 426B280SSGAP CG28E 406LNML M225CR2.80TM2.5LR 3225MCG2.80TM2.5LR 426B280MMGAP CJ28W 406LFLN W225CR2.80HR 3225WCG2.80HR 426B280RSGWA CN28W 406LFLNA W225CR2.80R 3225WCG2.80R 426B280ASGWA CT28W 406LFLNT W225CR2.80T0R 3225WCG2.80T0R 426B280TSGWA CV28W 406LFLNS W225CR2.80T2R 3225WCG2.80T2R 426B280SSGWA CG28W 406LFLNM MW225CR2.80TM2.5R 3225MWCG2.80TM2.5R 426B280MMGW
