1、INCHPOUND AA59789/22 22 October 2011 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .260 INCH BODY SIZE, WITH TWO OR NO MOUNTING HOLES AND VISUAL LOCK INDICATION, SCREW ACTUATED The General Services Administratio
2、n has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This comm
3、ercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59789 CID number /22 Applicable CID sheet * Configuration (see table I) * Finish * * Length (see table II)
4、* Mounting (see table I) Example: AA59789/22CR65S is the PIN for a clear chemical film finished, 6.3 inch (160 mm) long card holder. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners and a lockwasher and flat washer under the screw head for added resistance to
5、 loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card firmly in its installed positions and prevent loosening or movement as a result of shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly to the cold plate. Interface
6、 and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. The card holders shall have a visual indicator to show when the assembly is in its relaxed (unlocked) and expanded (locked) sta
7、te. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “N“, “S“, “R“, “P“, “U“, and “T“. Cold plate slot width. Th
8、e recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is as follows: 6 inch-pound
9、s (68 N-cm) for assemblies of configuration “A“, “C“, “F“, or “W“ and 7.2 inch-pounds (81 N-cm) for assemblies of configurations “D“, “J“, “L“, or “N“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/22 2 Configuration. The
10、configuration of a card holder shall be as specified in table I. The details of a particular configuration consist of those on figures 1, 2 and 3, and may include those on figures 4 or 5. TABLE I. Configuration. Configuration Mounting body style (see figure 2) Mounting options Applicable figures Har
11、dware options A A P, S, R, T 1, 2 and 3 No hardware options added C C N, S, R, T F A P, S, R, T 1, 2, 3 and 4 Lockwasher and flat washer W C N, S, R, T N A P, S, R, T 1, 2, 3 and 5 Screw self-lock element L C N, S, R, T J A P, S, R, T 1, 2, 3, 4 and 5 Lockwasher, flat washer, and screw self-lock ele
12、ment D C N, S, R, T Inches mm Inches mm Inches mm .125 .140 3.18 3.56 .225 .270 5.72 6.86 .30 .900 7.6 22.86 FIGURE 1. Relaxed and expanded dimensions (two mounting hole version shown). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/22 3 NOT
13、ES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Screw and alignment spring not shown. See table II and figure 2 for hole s
14、pacing requirements. 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm). 5. Mounting body style “A“ is capable of safely expanding to .330 inch (8.38 mm) and mounting body style “C“ is capable of expanding to .325 inch (8.26 mm) minimum. 6. Maximum screw advance is .12 i
15、nch (3.0 mm) for mounting body style “A“ and .14 inch (3.6 mm) for mounting body style “C“. FIGURE 1. Relaxed and expanded dimensions Continued. Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the
16、card holder is in the unlocked (relaxed) state, the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that the assembly is in the locked position, this red band shall be concealed. FIGUR
17、E 2. Visual lock indicator. Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film). Length,
18、 expanded and relaxed dimensions. The length designator shall be as specified in AA59789. The lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE II. Additional assembly dimensions (see figur
19、e 1 and 2). 1/ PIN length designator Dimension “L“ .02 (0.5) Mounting body style Dimension “A“ .01 (0.3) Dimension “B“ .02 (0.5) Dimension “M“ 2/ 50 4.8 (121.9) A 1.50 (38.1) .30 (7.6) .900 C 1.60 (40.6) .35 (8.9) .900 55 5.3 (134.6) A 2.00 (50.8) .55 (14.0) .900 C 1.60 (40.6) .35 (8.9) .900 60 5.8
20、(147.3) A 2.50 (63.5) .80 (20.3) .900 C 1.60 (40.6) .35 (8.9) .900 65 6.3 (160.0) A 3.00 (71.2) 1.05 (26.7) .900 C 1.60 (40.6) .35 (8.9) .900 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. 2/ Tolerance for the hole spacing is .005 inch (0.51 mm). Pr
21、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/22 4 Mounting body style (see figure 3 and table II). Two mounting body styles are available on this CID specification sheet, style A or style C. The primary difference in the two mounting body st
22、yles are the location of mounting holes on the mounting body as depicted on figure 2. Mounting body style A always has two locations for fasteners centered on the mounting body that are .900 inch (22.86 mm) apart. Mounting body style C can have two or no holes on the mounting body. NOTES: 1. Dimensi
23、ons are in inches. Millimeters are given for general information only. 2. See table II for dimensions B, E, and M. FIGURE 3. Mounting body style details. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/22 5 Mounting. The mounting designators
24、shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “N“ (no mounting holes; mounting body style C only), “P“ (.062 x .040 index pins; mounting body style A only), “R“ (rivet mount holes with counterbore and countersink), “S“ (tapped 256 h
25、oles), or “T“ (tapped 080 holes). See figure 1 for mounting hole spacing requirements. Card holders using mounting option “P“ and “R“ may be shipped unassembled. Rivet mount holes. The holes used for rivet mounting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch
26、 (3.56 mm) diameter through holes with a counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59789 when rivet mounting is used. Configuration hardware options. Card holders can have the following hardware options. See
27、 table I for the correct PIN configuration identifier. Lockwasher and flat washer (see figure 4). A lockwasher and flat washer located under the screw head will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include
28、configuration identifier “F“ or “W“ in the PIN (see classification and notes sections herein). FIGURE 4. Lockwasher and flat washer details. Screw self-locking element (see figure 5). The use of a screw self-locking element will provide prevailing torque for resistance to loosening of the assembly f
29、rom shock vibration. The screw self-locking element shall be in accordance with AA59789. Card holders requiring a screw self-locking element shall include configuration identifier “L“ or “N“ in the PIN (see classification and notes sections herein). FIGURE 5. Screw self-locking element details. Lock
30、washer, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include configuration identifier “D“ or “J“ in the PIN (see classification and notes sections herein). Provided by IHSNot for ResaleNo reproduction or ne
31、tworking permitted without license from IHS-,-,-AA59789/22 6 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder,
32、Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D
33、, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification shee
34、t preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacture
35、rs shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 URL: 61081 Calmark A Division of P
36、entair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail:
37、URL: Part number supersession data. These CID specification sheet PINs supersede the following manufacturers part numbers in table III and on DESC Drawing 89064 (table IV) as shown. The CID PINs listed in table III are only for length designator “50“. See tables V and VI for CID PIN construction us
38、ing other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/22 7 TABLE III. Commercia
39、l part number supersession data. PIN designator AA59789/22 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/22 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 AB50S 405VI10B CB50S VA226CR4.80T2
40、5226VBA4.80T2 AB50R 405VI10BR CB50R VA226CR4.80H 5226VBA4.80H AB50T 405VI10BT CB50T VA226CR4.80T0 5226VBA4.80T0 AB50P 405VI10BP CB50U VA226CR4.80TM2 5226VBA4.80TM2 FB50S 405VI10BLF WB50S WVA226CR4.80T2 5226VWBA4.80T2 FB50R 405VI10BLFR WB50R WVA226CR4.80H 5226VWBA4.80H FB50T 405VI10BLFT WB50T WVA226C
41、R4.80T0 5226VWBA4.80T0 FB50P 405VI10BLFP WB50U WVA226CR4.80TM2 5226VWBA4.80TM2 NB50S 405VI10BL LB50S VA226CR4.80T2L 5226VBA4.80T2L NB50R 405VI10BRL LB50R VA226CR4.80HL 5226VBA4.80HL NB50T 405VI10BTL LB50T VA226CR4.80T0L 5226VBA4.80T0L NB50P 405VI10BPL LB50U VA226CR4.80TM2L 5226VBA4.80TM2L JB50S 405V
42、I10BLFL DB50S WVA226CR4.80T2L 5226VWBA4.80T2L JB50R 405VI10BLFRL DB50R WVA226CR4.80HL 5226VWBA4.80HL JB50T 405VI10BLFTL DB50T WVA226CR4.80T0L 5226VWBA4.80T0L JB50P 405VI10BLFPL DB50U WVA226CR4.80TM2L 5226VWBA4.80TM2L AC50S 405VI10 CC50S V226CR4.80T2 5226VCG4.80T2 AC50R 405VI10R CC50R V226CR4.80H 522
43、6VCG4.80H AC50T 405VI10T CC50T V226CR4.80T0 5226VCG4.80T0 AC50P 405VI10P CC50U V226CR4.80TM2 5226VCG4.80TM2 FC50S 405VI10LF WC50S WV226CR4.80T2 5226VWCG4.80T2 FC50R 405VI10LFR WC50R WV226CR4.80H 5226VWCG4.80H FC50T 405VI10LFT WC50T WV226CR4.80T0 5226VWCG4.80T0 FC50P 405VI10LFP WC50U WV226CR4.80TM2 5
44、226VWCG4.80TM2 NC50S 405VI10L LC50S V226CR4.80T2L 5226VCG4.80T2L NC50R 405VI10RL LC50R V226CR4.80HL 5226VCG4.80HL NC50T 405VI10TL LC50T V226CR4.80T0L 5226VCG4.80T0L NC50P 405VI10PL LC50U V226CR4.80TM2L 5226VCG4.80TM2L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or netw
45、orking permitted without license from IHS-,-,-AA59789/22 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/22 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/22 Vendor similar designator or type part number 1/ CAGE 61081 Vendor
46、 similar designator or type part number 1/ CAGE 5BG68 JC50S 405VI10LFL DC50S WV226CR4.80T2L 5226VWCG4.80T2L JC50R 405VI10LFRL DC50R WV226CR4.80HL 5226VWCG4.80HL JC50T 405VI10LFTL DC50T WV226CR4.80T0L 5226VWCG4.80T0L JC50P 405VI10LFPL DC50U WV226CR4.80TM2L 5226VWCG4.80TM2L AP50S 405VI10N CE50S VEN226
47、CR4.80T2 5226VEN4.80T2 AP50R 405VI10NR CE50R VEN226CR4.80H 5226VEN4.80H AP50T 405VI10NT CE50T VEN226CR4.80T0 5226VEN4.80T0 AP50P 405VI10NP CE50U VEN226CR4.80TM2 5226VEN4.80TM2 FP50S 405VI10NLF WE50S WVEN226CR4.80T2 5226VWEN4.80T2 FP50R 405VI10NLFR WE50R WVEN226CR4.80H 5226VWEN4.80H FP50T 405VI10NLFT WE50T WVEN226CR4.80T0 5226VWEN4.80T0 FP50P 405VI10NLFP WE50U WVEN226CR4.80TM2 5226VWEN4.80TM2 NP50S 405VI10NL LE50S VEN226CR4.80T2L 5226VEN4.80T2L NP50R 405VI10NRL LE50R VEN226CR4.80HL 5226VEN4.8
