1、c b A-A-55060 84 7777774 0067339 8 1 INCH-POUND 1 A-A-5506 O JUN 19 19% COMMERCIAL ITEM DESCRIPTION GLOVES, MENS AND WOMENS HEAVY DUTY The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-G-2366. Classification. The mens and womens heavy
2、 duty leather work gloves shall be of one type. SALIENT CHARACTERISTICS Description. The gloves shall be a slip-on, half inseamed, all leather, gunncut design with a buckle strap closure on the back of the wrist and a leather reinforcement covering the palm. The seam at the base of the fingers shall
3、 be provided with a leather reinforcement welt turned up to cover the stitching as shown in figure 1. The curved fingertips of the four fingers shall be shirred on the palm side prior to the closing operations. The buckles shall be 5/8 inch, double bar, tongueless, lip type and shall conform to type
4、 II, style 3, class 3 requirements of MIL-B-543. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South
5、20th Street, Philadelphia, PA 19101-8419, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. a Provided by IHS
6、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-550b0 84 7777774 0067340 4 A-A-55060 Ihe gloves niay be furnished in any of the following three al t-erna1.c bark cons t ruct.i ons : I)(s i gri I - oric I)i CC-C hc:k arid f rorit, continuous thumb inseam w1 1-h
7、Ilil) wc.1 t i ricer t, full grain leather, (see f igiirc 1 ) I)tlsi-ri I I - Separac hr-1 arid f i-ont pieces lap seam joined at junc-t i ori of mi cid 1 e and i ndex fingers , continuous t Iiiimt? i r:sp( f i qui i ) 1)c.s i (311 I i :;cpratP back and iront pieces lap sean joined at Tape. lIi(2 t
8、rl): f ot- IOOJ irid kuc:kl ct.rap shall have an AATCC chroriiit J (7 ii-ciiisf ei-cncc Scale r-ati rig i or wet crocking not lower than 1 .S, 3nd foi- ry crocking not lower than 3.5. The color of tlie t-apc slid1 1 c-losely match the color of the glove leather. The tape sliiI I kx of woven cotLori
9、usirig t.wo ground warps (face and back), a binder warp, and filling. The face warp shall weave plain weave with picks that show an the face. The back warp chll weave plain with the picks that show on the back. The hinder warp ends shall weave one up and one down. When latch type shuttleless looms a
10、re utilized, the filling yarn shall i-raverse the full width of the tape and shall be held at the edge by an ext.ra catch-cord end interlacing with the filling yarn. When bobbin type shuttleless looms are utilized, interlacing of the catch-cord and filling shall occur within the selvage area before
11、the first binder end. The weight of the tape shall be 0.21 ounce per linear yard minimum. The minimum yarns for the full width shall be 61 for the face and back warp, and 13 for the binder warp. For the filling, the tape shall have 42 yarns per inch (i yarn per shed) of 20/2 ply, or 84 yarns per inc
12、h (2 yarns per shed) of 40/2 ply. The minimuin breaking strength of the warp for full width shall be 16/2, and 20/2 for the binder. The yarn size for the filling shall be 20/2 or 40/2. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I e * A-A-550b0
13、 84 m 9999974 OOb7L4L b m A-A-5 5 O 6 O Leather. The gloves shall be made from full grain cattlehide or full grain horsehide. The full grain cattlehide shall conform to all reuuirements of type II, class A or B of MIL-L-40051 excluding the thickness requirements. The full grain horsehide shall confo
14、rm to all requirements of type VI1 of KK-L-2004, except for thickness. Only split cattlehide leather shall be used for the back piece of the glove designs II and III as an alternative to the full grain leather. The split cattlehide shall conform to all requirements of type VI11 of KK-L-2004 except t
15、hat the split leather shall also conform to the colorfastness requirements specified for type V pf KK-L-2004, excluding the thickness requirements. The color of the leather shall be cream. The thickness of the parts of the finished gloves, except the welts, shall be not less than 3.1 ounces nor more
16、 than 4.0 ounces. The thickness of the leather welt strap and the thumb welt shall be not less than 2.0 nor more than 4.0 ounces. The gloves shall be paired with left and right hands of matching design style and corresponding leather types. Label. Each glove shall have a combination size and identif
17、ication label and the label shall show fastness to laundering transference. When cattlehide is used, the nomenclature in the label shall be Gloves, Heavy Duty, Cattlehide. When horsehide is used, the nomenclature in the label shall be Gloves, Heavy Duty, Horsehide. The label shall include the contra
18、ct number, National Stock No., and contractors name in addition to the size of the glove. A Printed slip of thin paper containing instructions as indicated below shall be inserted in each right-hand glove: WEARING INSTRUCTIONS In cold weather wear gloves over glove inserts, cold weather. In warm wea
19、ther the glove without the insert is sufficient. Fit gloves snugly but not tightly over glove inserts. Adjust strap for fit. Gloves and glove inserts are available in five sizes: 1, 2, 3, 4, and 5. Wash gloves in mild soap and lukewarm water or dry-clean them. Dry gloves and glove inserts away from
20、extreme heat or flame. Use for heavy work (construction, stevedoring, etc.). When conditions require chemical protective handwear to be worn the leather gloves are to be worn over the chemical protective handwear to provide maximum durability. Thread. The gloves shall be sewn with a natural color th
21、read conforming to type II, class A, size F of V-T-295. As alternative, natural color polyester thread conforming to type II, class 1, subclass A, size A, size F of V-T-285 may be used. Neither cotton nor aramid threads shall be used for stitching any part of the glove. 3 Provided by IHSNot for Resa
22、leNo reproduction or networking permitted without license from IHS-,-,-A-A-55060 4 I 9999974 0067342 m A-A-5 5 O 6 O Patterns. The government shall furnish all five size patterns of the item. Sizes and Measurements. The finished gloves shall conform to the measurements below. Measurement of qloves S
23、ize Overall length 1/ (inches ) Width 2/ ( inches ) 9 3/8 9 3/4 10 1/8 10 1/2 10 7/8 4 4 1/2 5 5 1/2 6 Tolerance + 3/4, - 1/4 - + 1/4 1/ The glove length shall be measured from tip of middle finger to edge of cuff. 2/ The glove width shall be stretched out and measured 1/2 inch from base of little f
24、inger. Workmanship. After completion, the finished glove shall be thoroughly cleaned, and all loose thread, lint, and foreign matter removed. Product Demonstration Model. When required, of ferers shall submit two (2) pairs of gloves of their intended production. The Product Demonstration Model will
25、consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model app
26、roved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance wit
27、h the Commercial Item Description specified above. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Responsibility for Inspection. The supplier is responsible for assuring the product conforms to the requirements. Glove lots will be inspected to det
28、ermine conformance with the Commercial Item Description and the successful offerers technical proposal as negotiated. Acceptability of glove lots will be determined by the use of “Sampling Procedures and Tables for Inspection by Attributes“, ANSI 21.4, published by the American Society for Quality C
29、ontrol. Sampling procedures will be designated by the Government at the time of award. The sample unit is one glove and the sample size shall be drawn in pairs. Leather inspection shall be performed in accordance with FED-STD-311. Defects. The gloves shall be examined for the following defects: any
30、hole, cut, tear, color not as specified; any spot or stain (outside); thread ends not removed; label missing, incorrect, or illegible; measurement of item not as specified; not properly mated (i.e., right and left not of same size); not full grain (applies to all parts except when cattlehide splits
31、are used for design II and III back piece), not soft and pliable, grain damage or imperfections; leather improperly cut (i.e., excessive stretch in length direction, leather-flanky, loose or spongy, bony or thin spots); any component missing, not securely affixed or workmanship damage (i.e. crooked
32、finger or glove inadequately formed, etc.); any open seams (when one or more stitches joining a seam are broken) or needle chews likely to develop into a hole. Twisted fingers or thumb where any part of the seam is rotated 45 degrees or greater from the vertical, Packaqinq, Packinq, Markinq, and Pal
33、letization Packaging, packing, marking and palletization shall be in accordance with ASTM-D 3951, Standard Practice for Commercial Packaging, as specified for shipments to the Department of Defense, including Section 7. Each pair of gloves, of one size only shall be stacked with every pair reversed
34、end to end. One hundred and twenty pairs of gloves shall be packed in a snug fitting fiberboard box, class domestic style RSC-L, grade 275. Note: Each shipping container shall contain only one National Stock Number (NSN). Unitized loads, placing boxes on pallets, shall be used whenever total quantit
35、y for shipment to one destination exceeds 250 pounds (excluding the pallet) or 20 cubic feet. Pallets shall have a length of 40 inches and a width of 48 inches. Pallet loads, including the pallet, shall not exceed 54 inches in height, 43 inches in length and 52 inches in width. The containers shall
36、be bonded onto wing type commercial 4-way entry pallets. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-550b0 4 m 9999974 0067344 3 m A-A-55 O 6 O Note: All palletized loads shall contain only one NSN, to the maximum extent possible. When ther
37、e is less than a pallet load per NSN, pallets may have containers not of the same NSN, but the pallet shall be clearly marked “mixed“ and each applicable NSN shall be listed together with its total quantity. Source of Government Documents. Copies of Military and Federal documents are available from:
38、 Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 B
39、roadway, New York, NY 10018- 3308. ) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodian: Army - GL Navy - NU Air force - 99 Review Activity: Army - M
40、D Air Force - 82, 45 User Activity: Navy - MC, SH Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. (8415-0874) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I RACK DESICN 1 A-A-55060 84 H 9999974 00b7L45 3 A-A-
41、5506 O 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55060 84 9999974 00b714b 5 A-A-55 O 6 O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55060 4 = 9999974 00b7147 7 = A-A-5506 O i: I ij i; i il -.-.-.-.,. il :I 1 ; 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
