1、. b 1 INCH-POUND I A-A-55087 29 October 1992 COMMERCIAL ITEM DESCRIPTION SHOES, SWIMMERS The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-S-19672. Abstract. This document covers lightweight coral swim shoes. The shoes are intended fo
2、r providing protection to the swimmers feet. Salient Characteristics. The shoe shall have a plain toe with a nylon duck upper and full length rubber outsole. The shoe shall be a sewed-vulcanized fabrication and include full cotton fabric insole. lace eyelets with nylon laces, or a zipper, or in a pu
3、ll on style. The shoe shall have an area of mesh or drain eyelets to allow water to drain out. The color of the outsole compound shall be gray to conform to #36118 of FED-STD-595. Nylon or polyester duck shall be dyed colorfast to match the color specified for the outsole above. Height of shoes shal
4、l be standard commercial grade between sizes. Inside back height for size 8 shoe shall be 5-1/4 inches. It may be constructed with a half bellows tongue and Material. Rubber, Rubber shall be natural rubber, synthetic rubber, or a mixture of natural and synthetic rubber. When tested in accordance wit
5、h this document, rubber compounds shall be of the composition and physical requirements specified herein. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothi
6、ng and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distributio
7、n is unlimited. FSC 8430 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55087 9999974 0339260 227 4 A-A-5 5 O 8 7 Nvlon or Polyester Duck. Nylon or polyester duck for the upper shall be woven from not less than three ply twisted thread in both
8、warp and filling and shall conform to the requirements specified herein. Cotton Fabrics. The fabrics shall be preshrunk, unbleached, and treated to resist fungi. The mildew inhibitor used shall be 2, 2 methylene-bis (4 chloro-phenol). Thread. The thread shall be nylon. The color shall be as specifie
9、d for the outsole above. The thread shall be colorfast to light, salt water, and soap. Ink, Markinq, Indelible. The ink shall be black and shall produce marks which are clear and legible. There shall be no offsetting or transfer and no discoloration beyond the limits of the marks. Quarter. The quart
10、er shall be cut from an integral piece of nylon duck. Vamp. The vamp shall be cut from an integral piece of nylon or polyester duck. Inside Toe Cap. The inside toe cap shall be knitted cotton fabric, nominal weight 5.5 ounces per square yard. The cap shall be coated on one side with the lining compo
11、und; shall cover the entire inside toe area and extend approximately 1-1/4 inches back from the point of the toe. - Sole. The sole shall be constructed as described below. Outsole. The outsole shall be fine crepe curl of outsole compound, 0.150 inch thick at the ball, and 0.200 inch thick at the hee
12、l. The outsole shall be plain edge. Foxinq. Foxing shall be of the upper compound, under the outsole type. The foxing shall be 1/2 inch wide and 0.025 to 0.040 inch in thickness. Binder Sole. The binder sole shall be cotton fabric, 5.4 2 0.5 ounces per square yard. The sole shall be frictioned on bo
13、th sides and coated on one side with the lining compound to a total thickness of 0.025 inch. Filler Sole. The filler sole shall be a good grade of stiffening compound 0.050 to 0.060 inch thick. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55
14、087 m 9999974 0119261 163 m A-A-5 5 O 87 Length of bottom Width of ball Width of heel Heel to crown Waist Ball girth Toe spring Insole. The insole shall be cotton fabric, 7.2 2 0.5 ounces per square yard. The insole shall be coated on one side with a good grade of stiffening compound and laminated t
15、o the stiffening compound coated side of a cotton fabric 5.4 0.5 ounces per square yard; coated on one side with a good grade of stiffening compound, total thickness of insole 0.100 inch. Medium (M) Width Grade between each full size 10-13/16 1/3 3-8/12 1/12 2-15/32 Blend 13-3/8 3/8 9-1/2 1/4 9-5/8
16、1/4 3/4 Blend Sizes and Width. The shoes shall be provided in the following sizes and width: Sizes - 6; 6-1/2; 7; 7-1/2; 8; 8-1/2; 9; 9-1/2; 10; 10-1/2; Width - Medium (M) 11; 11-1/2; 12; 12-1/2 Markinq. Each shoe shall be stamped inside the quarter with the letters “US“, shoe size, width, contract
17、or order number and the contractors name as follows: us 8-1/2 (M) Contract or order No. Contractors name Stamping shall be block letters in black ink as described above; 3/8 inch high in first line, 7/32 inch second line; and 3/16 inch third and fourth line. Sizes and Measurements. Lasts shall confo
18、rm to Table I. Dimensional tolerance for the finished shoes shall be within the limit of plus or minus 3-1/2 percent of the dimensions specified. Workmanship. After completion, the finished shoes shall be thoroughly cleaned, and all loose thread, lint, and foreign matter removed. Provided by IHSNot
19、for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 5 5 O 8 7 Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration M
20、odels will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufa
21、cturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Qualitv Assura
22、nce Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of
23、 such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acce
24、ptance comply with all requirements of the contract. Examination. Shoe lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The shoes shall be examined for
25、the defects listed below. The lot size shall be expressed in units of shoes. The sample unit is one shoe. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 6.5. Defects. The shoe shall be examined for the following defe
26、cts: any hole, cut, tear, rip, mend, weak place or other deficiencies seriously affecting serviceability; exterior color not as specified; exterior color not uniform; any spot or stain (outside); shoes not properly mated (i.e., not right and left of same size); height variation between pair; any com
27、ponent not fabricated of the specified material; design not as specified; any component missing; defective or damaged component affecting serviceability; any component misplaced, seriously affecting serviceability; raw edge showing; irregular or uneven stitching affecting appearance; loose stitch te
28、nsion resulting in a loosely secured seam; tight stitch tension resulting in puckering of fabric or assembly; any open seam; rubber components not securely bonded or vulcanized; burned gum; porous or imbedded foreign 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
29、nse from IHS-,-,-A-A-55087 matter; poor or incomplete vulcanization; eyelets not securely clinched (if used); eyelets not in proper alignment interfering with proper lacing (if used); thread ends not removed; marking missing, incorrect, or illegible, not applied in the specified manner, misplaced, o
30、r size or color not as specified; measurement of item not as specified. Dimensional Examination. The finished shoes shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one shoe; the inspection
31、 level shall be II and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Packasina Examination. The fully packaged shipping Containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The i
32、nspection level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 2.5. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Ma ter ia 1 s Workmanship Con?-ent Palletization Any component missi
33、ng, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items not as specified on shipping conta
34、iner Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55087 m 9999974 0119264 972 m J Requirement 63 (by weight) A-A-5 5 O
35、8 7 Test Method FED-STD-601 16101 Reuulatory Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. End Item Performance Testinq. Minimum percent new rubber Upper Compound. The upper compound shall conform
36、 to the composition, tensile strength (before aging), tensile strength (after aging), and ultimate elongation requirements in Table II below. I 16101 42 (by weight) Table II. Upper Compound End Item Performance Requirements Characteristic Minimum percent rubber Minimum percent new rubber Tensile str
37、ength, minimum Tensile strength after acceler- ated aging, min. Ultimate elonga- tion, percent minimum iequirement 56 (by weight) 56 (by weight) 1,400 pounds/ square in.-psi 1,050 psi 400 16101 16101 4111 4111 and 7001 4121 Results Reported to: nearest percent nearest percent nearest 1 O psi nearest
38、 5 percent Lininq Compound. The lining compound shall conform to the composition requirements in Table III below. Table III. Lininq Compound End Item Performance Requirements Characteristic Minimum percent rubber Deter. Per Sample Unit Results Reported to: nearest percent nearest percent Outsole Com
39、pound. The outsole compound shall conform to the composition and resistance to abrasion requirements in Table IV below. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55087 D 9999974 OLL9265 809 W Characteristic A-A-55087 Table IV. Outsole Com
40、pound End Item Performance Requirements Requirement Test Method FED-STD-601 Deter. Per Results Sample Unit Reported 1 to: Minimum percent rubber Minimum percent new rubber Resistance to abrasion, minimum 16101 16101 14111 45 (by weight) 45 (by weight) 35 nearest percent nearest percent nearest index
41、 unit Nvlon or Polyester Duck. The nylon or polyester duck shall be woven from not less than three ply twisted thread in both warp and filling and shall conform to the weight, thread count, tensile strength, and colorfastness requirements in Table V below. Table V. Nylon or Polyester Duck End Item P
42、erformance Requirements Characteristic Nominal weight per square yard, min. Thread count Warp, minimum Filling, minimum Tensile strength Warp, minimum Filling, minimum Colorfastness soap Salt water and Light Requirement 14 ounces 38 per inch 23 per inch 600 pounds 350 pounds I good “ “ good I rest M
43、ethod FED-STD-191 5041 5050 5050 5100 5100 5632 5660 Deter. Per Sample Unit Results Reported to: 0.1 oz number number one pound one pound good, fair, good, fair, or poor or poor Cotton Fabrics. Material identification for cotton fabrics for the lace eyelet stay, drain eyelet stay, counter and counte
44、r bind shall be in accordance with Test Method 1200 of FED-STD-191. All weight requirements stated in this document for cotton fabrics shall be in accordance with Test Method 5041 of FED-STD-191. Preservation, Packinq, and Markinq. The preservation, packing, and marking shall be as specified in the
45、contract or order. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55087 m 9999974 01iL92bb 745 m A-A-5508 7 Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg.
46、 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-D
47、 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodian: DLA - CT a Civil Agency Coordinating Activity: - GSA - FSS Preparing Activity: DLA - CT Project No. 8430-0409 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
