1、A-A-55 II II 9 m 9999974 OL43bb2 T84 m A-A-5 5 11 9 23 March 1993 COMMERCIAL ITEM DESCRIPTION GLOVE INSERTS, COLD WEATHER This Commercial Item Description is authorized for use in preference to MIL-G-835. Abstract. This Commercial Item Description covers an ambidextrous, knitted glove insert, to be
2、worn for added warmth with glove shells for cold weather and is intended for wear by Defense Department personnel. Classification. The classes: Type 1 Type II Class 1 Class 2 gloves shall be in the following types and - Non-automatic construction - Automatic construction - Camouflage Green 483 - Gra
3、y 1155 Salient character,st,cs. The glove inserts shall be ambidextrous design with knitted hands, fingers and thumbs. gloves except the cuffs shall be knit seamless with a plain (jersey) stitch. The cuffs for type I construction shall be a true 1 x 1 rib knit. The cuffs for type II construction sha
4、ll be a mock rib knit and have two elastic (spandex) yarns inserted around the top edge of the cuff. The two elastic yarns shall be overedged. Type II gloves shall be made on fully automatic flat bed knitting machines. All parts of the Beneficial comments (recommendations, additions, deletions) and
5、any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 142
6、6) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. FSC 8415 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55119 D 9999974 OL43bb3 910 A-A- 5 5 1 19 F
7、iuures. Figures 1 and 2 are furnished for information purposes only. To the extent of any inconsistencies between the written Commercial Item Description and the figures, the written Commercial Item Description shall govern. Material. Yarn. The yarn shall be a wool-nylon blend, mixed, carded, spun a
8、nd twisted into the counts and turns per inch specified in Table I: Table I. Yarn counts and turns Count of yarn, woolen Turns per inch spun (cut system) (2 1 Single Ply yarn number) (2 1 turn) (2 0.5 turn) Type 1 Hand, fingers, and thumb 1 end 2/15 10 Cuff 1 end 3/15 10 1 end 1/15 and 1 end 10 or 2
9、/15 Type II Hand, fingers, thumb, and 1 end 2/15 cuff 10 4 Wool. The wool shall be virgin fleece or pulled sheeps wool, or a blend of both, not lower in grade than 56s US Standard. The use of noils, card fly, card stripping, reused wool, reprocessed wool, fiber obtained from knitting clips, garnette
10、d hard ends, and similar waste is prohibited. Nylon. The nylon shall be 6 denier virgin nylon, crimped and cut to a staple length of not less than 2-3/8 inches nor more than 3- 1/8 inches. Non-fibrous materials. The finished glove inserts shall contain not more than 3.0 percent starch and protein co
11、ntent including chloroform-and water-soluble material and shall be in accordance to ASTM-D 629, Section 9. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55119 m 9999974 0143664 857 m A-A- 5 5 1 19 Fiber content. The wool/nylon blended portion
12、 of the finished glove inserts (based on a dry, extracted and desized basis) . shall contain not less than 25% percent nor more than 32% nylon with the remainder all wool and shall be in accordance with Test Method 2611 of FED-STD-191. Thread. For type I construction, the thread for sewing (closing)
13、 the tips of the thumb and fingers shall be polyester, spun, class 1 or 2 of MIL-T-43624. Ticket No. 50, 3 ply shall be used as the needle thread and ticket No. 70, 3 ply shall be used as the looper thread. For type II construction in overedging the top of the cuff, the thread for the needle and one
14、 of the loopers shall be polyester, cotton-covered, ticket No. 70, 2 ply conforming to A-A-50199. The same yarn used to knit the inserts, except that it will be one end of singles 15s, shall be used in the other looper so that the yarn is on the outside edge of the cuff. Color. The color of the glov
15、e insert shall be Camouflage Green 483. The thread shall be dyed Camouflage Green 483 for the class 1 glove insert and Medium Gray AV C.A. 66062 for the class 2 glove insert. The glove insert including thread shall show fastness to laundering and perspiration equal to or better than the standard sam
16、ple. When no sample is available, the thread shall show good fastness to laundering and perspiration. The color shall match the standard sample when viewed under filtered tungsten lamps which approximate artificial having a correlated color temperature of 7500 the inspection level shall be S-3 and t
17、he AQL, expressed in terms of defects per hundred units, shall be 1.5. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55119 D 99999iq OL43b73 8bT A-A-55119 5. shall be examined in accordance with defects listed below. The lot size shall be th
18、e number of shipping containers in the inspection lot. expressed in terms of defects per hundred units, shall be 1.0. The fully packaged shipping containers The inspection level shall be S-2 and AQL, EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, loca
19、tion, or method of application Materials Workmanship Content Palletization Any component missing, damaged, Inadequate application of components, such as: incomplete closure of container flaps, loose strapping., improper taping, or inadequate stapling or not as specified Number of items per container
20、 is more or less than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified End ItemPerformance Testinq. The glove inserts shall have a #3 colorfastness
21、rating to laundering and perspiration when tested in accordance with AATCC Test Methods 61 and 15. Preservation, Packina, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. 12 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
22、t license from IHS-,-,-A-A-55 II II 9 m 9999974 0143674 7Tb m A-A-55 119 Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonuovernment Documents. ANSI/
23、ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) (Applications for copies should be addressed to American ASTM-D 629 - Non-fibrous materials (Applications for copies should be addressed to American Societ
24、y For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) AATCC 15 - Colorfastness to Perspiration AATCC 61 - Colorfastness to Launering, Home, and Commercial: Accelerated (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.
25、O. Box 12215, Triangle Park, NC 27709-2215) Custodian: Army - GL Navy - NU Air Force - 99 Review Activity: Navy - AS Air Force - 11, 82, 45 User Activity: Navy - MC Coast Guard - CG 13 Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8415-0912 Provided by IHSNo
26、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55119 M 9999974 0143b75 632 M A-A-55119 -e o I L / s I P FIGURE 1 - GLOVE, INSERTS, COLD WEATHER (TYPE I CONSTRUCTION) 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55 L 19 m 9999974 0343676 579 m ji-A-51113 FIGURE 2 - G,LOVE, INSERTS, COLD WEATHER (TYPE II CONSTRUCTION) 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
