1、A-A-55193 m 9999974 0143327 137 m A-A-55 19 3 29 MARCH 1993 COMMERCIAL ITEM DESCRIPTION HOLDER, CARTRIDGE, BELT, CAL. .38, LEATHER, BLACK, 6-ROUND The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-H-13102. Abstract. The cartridge hold
2、er is intended for wear on a leather belt to hold six rounds of 38-caliber ammunition. Salient Characteristics. piece leather construction: main body with a 1-3/8 inch belt slot and retaining strip. The color of the flesh side shall be natural. For finishing the edges of the leather, a colorless aqu
3、eous solution shall be used. The overall dimensions of the holder shall be 6-1/8 inch (+ 1/8, -1/16 inch) by 2 inches. (See Figure 1). The holder shall be comprised of two Materials. Leather. The leather shall be vegetable tanned, top grain cattlehide. smoothly on the grain side, insuring a long-las
4、ting lustrous finish. retaining strip 4 ounce. The thickness tolerances for both pieces shall be plus 1 ounce and minus 1/2 ounce. The leather shall be dyed black and finished The thickness shall be as follows: main body 8 ounce, Beneficial comments (recommendations, additions, deletions) and any pe
5、rtinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) app
6、earing at the end of this document or by letter. LMSC N/A FSC 846: DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 5 19 3 Thread. The thread for stitching shall b
7、e either 100-percent polyester or 100-percent nylon, soft or bonded finish, black, and 3-ply. 24 pounds. Label/markinq. side of the holder and shall be located in the middle (Figure 1). The contract number shall be indented on the flesh side of the holder. All characters shall be 3/8 inch in height.
8、 The thread shall have a minimum breaking strength of The letters lWS1g shall be indented on the grain Workmanship. The finished holder shall conform to the quality of product established by this document. shall not exceed the applicable acceptable quality levels. Product Demonstration Model. When r
9、equired, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation
10、. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demo
11、nstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. The occurrence of defects gualitv Assurance Certification. The contractor shall certify that the product offered meets the salient characterist
12、ics of this description and that the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under th
13、e provisions of the contract. Reliance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination. Holder lots shall be inspected in acc
14、ordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The holder shall be examined for the defects listed below. The lot size shall be expressed in units of holders. The sample unit is on
15、e holder. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 3.0. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55193 9999974 0143329 TOT A-A-5519 3 Defects. The
16、holder shall be examined for the following defects: any hole, cut, tear, color not as specified; any spot or stain (grain side); thread ends not removed; marking missing, incorrect, or illegible; thread not as specified or color of thread not as specified, not able to hold rounds of ammunition secur
17、ely, measurement of item not as specified. Dimensional Examination. The finished holder shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one holder; the inspection level shall be S-3 and th
18、e AQL, expressed in terms of defects per hundred units, shall be 1.5. Packaaina Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be
19、S-2 and AQL, expressed in terms of defects per hundred units, shall be 1.0. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application. Mater ia 1s Any component missing, damaged, or not as specified. Workmanship Inadequate appl
20、ication of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Content Palletization Number of items in container is more or less than required. NSN shown on one or more items not as specified on shipping container. Length, width, or
21、height exceeds specified maximum requirements. Pallet type not as specified. Load not bonded as specified. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55293 = 9999974 01143330 721 A-A-55 19 3 Reaulatorv Reauirements. use recovered materials
22、 in accordance with Public Law 94-580 to the maximum extent practicable. Preservation, Packina. and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government Documents. Copies of Military and Federal documents are available from: The offeror
23、/contractor is encouraged to Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonaovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection (Applications for copies should be addressed to American By Attributes National
24、 Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodian: DLA-CT Review Activity: Amy-GL C
25、ivil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0125 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55193 = 9999974 0143331 bb8 A-A-55153 2“ _FIGURE 1 HOLDER, CARTRIDGE, BELT, CAL. 38, LEATHER, BLACK, GIROUND 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
