1、A-A-55205 m 7779774 0/44610 573 m IINCH-POUNDI A-A-5 5 205 Mav 18, 1993 COMMERCIAL ITEM DESCRIPTION BAG, PERSONAL EFFECTS The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-B-3759. Abstract. This document covers a cotton sheeting cloth
2、 bag 7 inches in diameter and 8 inches in depth with a drawstring closure at the top. personal effects, such as wallet, watch, ring and other valuables pending inventory and return to the next of kin of deceased military personnel. The bag is used to store delivery mail and Salient Characteristics.
3、The construction of the bag shall conform to Figure 1 and shall be as specified herein. Materials. O Cloth, Sheetinq, Cotton. The cotton cloth shall be unbleached with a plain weave. The cloth shall be vat dyed, water-repellent and mildew resistant aftertreated, shade Camouflage Green CG-483. The wa
4、ter repellents shall consist of aluminum salts of saturated carboxylic acids (such as formate, acetate, palmitate or stearate), zirconium salts of such saturated carboxylic acids, or a combination of both, mixed with refined mineral and vegetable waxes, titanate esters, or a combination of both. The
5、 product shall be applied either in the form of an aqueous emulsion or in the form of a water free solvent solution. The mildew compound Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense P
6、ersonnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. msc N/A FSC 8465 DISTRIBUTION STATEMENT A. A
7、pproved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55205 9999974 OL44bLL 40T m Characteristic A-A-5 5 2 05 Requirement Test Method ASTM D3775-85 L/ - i/ Testing shall be performed after specime
8、n reaches equilibrium under standard conditions of 70220F and 6522% relative humidity. - 2/ One edge of the long dimension of the specimen shall be raveled until a continuous yarn, the length of the specimen, is obtained. Measure 1-1/2 inches in from this edge and draw a thin line the full length of
9、 the specimen. - 3/ The supplier shall certify that the specific inhibitor was used in the treatment of the cloth. Tape, Textile, Cotton (drawstrinus). The cotton tape shall be 1/4 inch in width, plain weave. The tape shall be water repellent, mildew resistant and dyed shade Olive Drab-7. The water
10、repellents shall consist of aluminum salts of saturated carboxylic acids (such as formate, acetate, palmitate or stearate), zirconium salts of such saturated carboxylic acids, or a combination of both, mixed with refined mineral and vegetable waxes, titanate esters, or a combination of both. The pro
11、duct shall be applied either in the form of an aqueous emulsion or in the form of a water free solvent solution. The mildew compound applied shall be copper 8-quinolinolate in solubilized form. The tape shall conform to the requirements in Table II below. 2 Provided by IHSNot for ResaleNo reproducti
12、on or networking permitted without license from IHS-,-,-A-A-55205 m 7777774 Ol44bL2 34b m Characteristic Requirement A-A-55 205 Test Method Total warp yarns 17 min. ASTM D3775-85 I/ -.Fillins yarns per inch 28 min. ASTM D3775-85 l/ Breaking strength (warp) 18 lbs. min. FED-STD-191 Nonfibrous materia
13、ls FED-STD-191 pH 5.5 - 8.5 ASTM D2165-90 4108 2/ content 10.0% max. 2611 Labile sulfur No more than slight trace FED-STD-191 Dynamic absorption - 2020 40% max. FED-STD-191 - - i/ Testing shall be performed after specimen reaches equilibrium under standard conditions of 70+20F and 6552% relative hum
14、idity. - 2/ Either split drum or flat surface clamps may be used. When flat surface clamps are used, the pulling clamp shall have a uniform speed of 12 0.5 inches per minute, the distance between jaws shall be 3 inches and the test specimen shall be a minimum - 3/ The supplier shall certify that the
15、 specific inhibitor was used in the treatment of the tape. of 6 inches. 4500 Inhibitor content 0.13 to 0.40% as copper FED-STD-191 copper 8-quinolinolate 2050 or 2060 a/ Thread. Thread can be either polyester or nylon with soft or bonded nonwicking finish, meeting a 4.3 pound (minimum) breaking stre
16、ngth when tested in accordance with method 4100 of FED-STD- 191. The thread shall be dyed Olive Drab S-1 (C.A. 66022) and shall show fastness to chlorine bleaching equal to or better than the standard shade sample. If no standard shade sample is available, the thread shall show good fastness to chlo
17、rine bleaching. Grommet, Metallic. The plain grommets with toothed washers shall conform to type II, class 3, size No. O of MIL-G-16491. Label/markinq. The statistics label, 5 inches long by 4 inches wide, shall be nonwoven, spunbonded polyester cloth or nonwoven, 80/20 polyester/cellulose cloth, an
18、d shall be stitched to the bag in the location shown in Figure 1. The impregnation coating shall be a pigmented acrylic or nitrocellulose coating composed of white pigments such as clay, chalk, titanium dioxide, or blane fixe, and affixed by an appropriate acrylic or nitrocellulose resin. The coatin
19、g composition shall not contain leachable skin irritants or toxic materials. Substances that will support mildew growth shall not be included. The finished impregnated labels shall have a smooth matte surface and shall be free from objectionable odors. Labels shall be clearly legible after 0 3 Provi
20、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55205 9999974 OL44bL3 282 A-A-5 5 2 O 5 O subjection to the accelerated laundering procedure specified in AATCC No. 61 Test IVA. Marking on the label shall be printed in 10-point size characters and shal
21、l be as follows: Deceased Military Personnel, Personal Effects Serial No. Grade Organization Address Nearest relative Address Killed in action Date Battle area Name Rank Died of disease Hospital Information O Place of burial Point of coordination Description of body Members missing Signed Sizes and
22、Measurements. measurements in Figure 1. The finished bag shall conform to the Workmanship. After completion, the finished bag shall be thoroughly cleaned, and all loose thread, lint, and foreign matter removed. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
23、om IHS-,-,-A-A-55205 = 9999974 OL4YbLY 119 = A-A-5 5 2 05 Product Demonstration Model. When required, of ferers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. evaluated by the government. Evaluation criteria and basis
24、 for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract
25、. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Requlatory Requirements. use recovered materials in accordance with Public Law 94-580 to the maximu
26、m extent practicable. Product Demonstration Models will be analyzed and The offeror/contractor is encouraged to Oualitv Assurance Certification. offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specifications, standards and qu
27、ality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall not relieve the contractor of the responsibilit
28、y of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. The contractor shall certify that the product 0 Examination. Bag lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attribute
29、s“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The bags shall be examined for the defects listed below. The sample unit is one bag. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units
30、, shall be 6.5. The lot size shall be expressed in units of bags. Defects. The bags shall be examined for the following defects: any hole, cut, tear in the cloth, color not as specified; any spot or stain (outside); thread ends not removed; broken or missing yarn, multiple floats clearly visible at
31、normal inspection distance (approximately 3 feet); shade bar; fine or coarse filling bar; edge of tape (drawstrings) frayed or scalloped; grommets broken; malformed grommets; grommets fail to perform intended function; corroded area on grommets; burr or sharp edge which may cause injury in handling
32、or damage to fabric; open seams; raw edges; thread breaks; chain portion of 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55205 m 9999974 0144615 055 m A-A-5 5 2 05 stitching indicated by “Z“ on Figure 1 shows on outside of bag; any component
33、 part not fabricated of applicable referenced material; hems formed on outside of bag in lieu of inside; seams badly pleated or puckered; one or both drawstrings caught in hem stitching failing to allow complete closing of bag; drawstring loops not threaded through grommets; bartacks omitted on eith
34、er side of seam; bartacks loose or tight, incomplete or broken; body of bag formed with more than 2 pieces of fabric; ends of seam joining bottom halves staggered at seams joining bottom to body by more than 3/8 inch; label missing, incorrect, illegible, misplaced, or characters not as specified; gr
35、ease or oil stains clearly noticeable; grommets set off-center of hem by more than 1/4 inch; grommets set off-center of closing seam by 1/8 inch or more; width of hem less than specified by more than 1/4 inch; bartacks set beyond location indicated on Figure 1 by more than 1/4 inch; overall dimensio
36、ns not within tolerances specified on Figure 1 (NOTE: The diameter of the finished bottom shall be taken from the bottom edge of body across bottom sections); not cut or fabricated in accordance with the product demonstration model; label missing, incorrect, or illegible; measurement of item not as
37、specified; any variance not otherwise classified herein but at a variance with the product demonstration model. Dimensional Examination. The finished bag shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample
38、unit shall be one bag; the inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Packauinq Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping c
39、ontainers in the inspection lot. The inspection level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 2.5. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Materia 1 s Workmanship Any co
40、mponent missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55205 =
41、 9999974 OLYYb1b T3L A-A-5 5 2 O5 EXAMINE DEFECT Content Palletization Number of items in container is more or less than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load no
42、t bonded as specified PACKAGING. Packaqinq. Ten bags shall be stacked in a bundle with labels facing up and secured with tape or twine. Packinq. Six hundred bags shall be placed in a fiberboard box conforming to RSC-L, grade 275 of PPP-B-636. The box shall be closed in accordance with the appendix o
43、f PPP-B-636. Palletization. Boxes shall be palletized on a 4-way entry pallet in accordance with load type Ia of MIL-STD-147. Each load shall be bonded with primary and secondary straps in accordance with bonding means C and D or film bonding means F or G. Pallet pattern shall be in accordance with
44、the appendix of MIL-STD-147. Markinq. Marking shall be in accordance with MIL-STD-129. Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonuovernment Do
45、cuments. AATCC Test Methods (Applications for copies should be addressed to American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, N.C. 27709.) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55 2 05 ANS
46、I/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM Test methods (Applications for copies should be addressed to American Society For Testing a
47、nd Materials, 1916 Race .Street, Philadelphia, PA 19103.) Custodian: Army - GL Navy - NU User Activity: Navy - MC Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0130 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-O e A-A-55205 = 9999974 0144618 864 A-A-5 5 2 05 * ! II CI t L ci Figure 1. Bag, Personal Effects 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
