1、A-A-55245 m 9999974 O15b299 O12 m I INCH-POUND I A-A-5524 5 November 12, 1993 COMMERCIAL ITEM DESCRIPTION NECKLACE, PERSONNEL, IDENTIFICATION TAG The General Services Administration has authorized the use of this commercial item description in preference to MIL-N-3019. Abstract. personnel to support
2、 two personnel identification tags. Salient characteristics. main loop and extension loop, made up of chain. The chain shall be composed of bead shaped and dumbbell shaped elements. The chain and splicing links shall be fabricated from corrosion resistant (stainless) steel. Each bead shaped element
3、shall be Number 3 size, with 97 beads per foot and a tolerance of plus 3 beads, minus none. The overall length of the main loop chain including the splicing link shall be 27 inches, plus 1/4 inch, minus O inch. The overall length of the extension loop chain including the splicing link shall be 5-1/2
4、 inches, plus 1/4 inch, minus O inch. One splicing link shall be used to join the ends of the main loop chain and one splicing link shall be used to join the ends of the extension loop chain. necklace shall be freely rotatable and longitudinally movable relative to each other. The necklace shall be
5、given a bright polished finish. The necklace does not include the identification tags shown in Figure 1. The necklace is intended to be worn by military The necklace shall be comprised of a qp All parts of the Beneficial comments (recommendations, additions, deletions) and any pertinent data which m
6、ay be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of
7、 this document or by letter. AMSC N/A FSC 8465 b DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. O Licensed by Information Handling ServicesA-A-55245 Material Steel, corrosion-resistant. The steel shall conform to types 304, 305 or 316, condition annealed, hot-rolle
8、d or cold-rolled of I ASTM-A 240. Label/markinq. The contractor may place his identification on * the splicing link provided there are no rough edges and the splicing link is not damaged or impaired. Workmanshir). After completion, the finished necklace shall be thoroughly cleaned, and be free from
9、grease, oil, rough surfaces or irregularities which may scratch, cut or otherwise cause discomfort to the wearer and shall be free from other defects which will affect appearance or serviceability. Product demonstration model. When required, offerers shall submit samples of their intended production
10、. The product demonstration model will consist of units independently developed. Three (3) product demonstration models will be analyzed and evaluated by the Government. and basis for award are contained in the solicitation. Product demonstration models will be retained by the Government. One (1) pr
11、oduct demonstration model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the product demonstration model does not relieve the successful offerer of his responsibility
12、 to perform in accordance with the commercial item description specified above. Evaluation criteria Requlatory reauirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality assurance Certification. The co
13、ntractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior t
14、o the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Reliance on contractor quality assurance systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comp
15、ly with all requirements of the contract. 2 Licensed by Information Handling ServicesA-A-55245 W 3399974 0356303 5TO 9 A-A-5 5 2 4 5 Examination Visual examination. The necklace shall be examined for the of necklaces. The sample unit is one necklace. . defects listed below. The lot size shall be exp
16、ressed in units ( Defects. The necklace shall be examined for the following defects: any part missing, chain kinks, splicing links malformed, oily or dirty, all parts not freely rotatable, finish not as specified, not made of specified material, metal cracks in beads or splicing links, beads per foo
17、t not within specified tolerance, measurement of items not as specified. Dimensional examination. The finished necklace shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one necklace. Packaa
18、ina examination. shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The fully packaged shipping containers EXAMINE DEFECT Marking Omitted, incorrect, illegible; (exterior and interior) of improper size, location,
19、or method of application . Materials Workmanship Content Palletization Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is mo
20、re or less than required NSN shown on one or more items is not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Licensed by Information Handling ServicesA-A- 5 5 2 4 5 End item Derformance tes
21、tinq. The necklace shall conform to the breaking strength requirements when tested. one necklace. shall have a breaking strength of not less than 15 pounds and not greater than 32 pounds. The section of the loop tested shall include the splicing link. Two breaking strength determinations shall be ma
22、de on each sample unit (one on the main loop and one on the extension loop). The testing machine shall consist of a means of supporting the chain, a means for slowly and uniformly applying the load to the chain, and a means for determining the applied load. machine in such a manner that there are no
23、 kinks in the chain, that the supporting means and the load applying means do not damage or distort the beads, and that the chain section tested includes the splicing link. A load of O to 15 pounds shall be applied uniformly over a period of 1 minute. The load shall then be uniformly increased to de
24、termine the maximum breaking strength. If the chain breaks within three beads of the clamping device the test shall be disregarded and repeated. The results shall be reported for each loop to the nearest 0.1 pound. Any result not falling within the limits specified shall be considered a test failure
25、. The sample unit is When tested the main loop and the extension loop The chain material shall be inserted in the Preservation. Dackina, and markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government documents. Copies of military and Federal
26、documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of non-Government documents ASTM-A 240 - Standard Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vess
27、els (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) Custodian: Army-GL Navy-NU Air Force-99 Review Activity: Army-MD Navy-PE Air Force-82, 45 Coast Guard-CG User Activity: Navy-MC Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0123 4 t Licensed by Information Handling ServicesA-A-55245 m 9999974 0356303 373 m A-A-55 2 4 5 n / - SPL I C i NG LINK NECKLACE, PERSONNEL, IDENTIFICATION TAG J FIGURE 1 5 Licensed by Information Handling Services
