1、A-A-5529b 9999974 0170581 T88 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FNS, 2800 South 20th Street, Philadelphia, PA
2、 19 145-5099. PCH-POUND I AD 1.1996 A-A-5 5296 COMMERCIAL ITEM DESCRIPTION CLOTH, TWILL, COTTON, 10.0 OUNCES (339 g) The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-C-43956 for all Federal agencies. 1. SCOPE 1.1 Scotle. This com
3、mercial item description covers the requirements for a cotton twill cloth intended for use in the lining for boots and shoes. 2. CLASSIFICATION. The cloth shall be furnished in the following classes: Class 1 - Class 2 - Natural or bleached Natural or bleached, mildew-resistant treated 3. SALIENT CHA
4、RACTERISTICS 3.1 DescriDtion. The cloth shall be manufactured from cotton which has been carded, drawn, and spun into a single yam. The weave shall be a three up and one down (3/1) right hand twill. The cloth shall have a starch and protein content (including chloroform-soluble and water-soluble mat
5、erial). The Class 2 cloth shall be mildew-resistant treated with copper-8-quinoliolate so as to deposit a copper content of metallic copper from copper-8-quinoliolate when tested in accordance with the requirements listed in Table I. The color of the cloth shall be natural or bleached. The color of
6、the Class 2 cloth shall be a shade imparted to the cloth as a result of the mildew resistant treatment. The width shall be as specified in the contract or purchase order. The cloth shall be finished so it will not unravel when cut. 3.2 Phvsical reauirements. The finished cloth shall conform to the r
7、equirements listed in Table I. AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55296 - 9999974 0370582 934 A-A-55296 TABLE I. Phvsical reauiremen
8、ts and test methods Characterktiq Requirement Test Method Yarn identification Cotton AATCC 20 Weight (odsq. yd, minimum): 10.0 Yarns per inch (minimum: warp 85 Filling 38 Breaking strength (pounds): warp 130 Filling 125 ASTM D-3776, Opt. C ASTM D-3775 ASTM D-3775 ASTM D-5034 ASTM D-5034 Weave Visual
9、 - 1/ Vonfibrous materials, Jercentage (maximum) 15.0 ASTM D-629 Zopper content (class 2), 0.15 f. .O5 TM 2050 of Jercentage FED-STD-191 Sopper-8-quinolinolate (class 2) - 21 I/ Unless otherwise specified, a certificate of compliance shall be submitted and will be acceptable for the stated requireme
10、nt. 2/ The contractor shall certi that only copper-8quinolinolate was used in the treatment of the cloth. 3.3 Len smash; knot or slub; spot or stain; embedded crease or wrinkle; two or more yams missing or broken for more than 9 inches; width not as specified; overall uncleanness. 5.3.3 Length exami
11、nation. During yard-by-yard examination, each roll in the sample shall be examined for length. Any length found to be less than the minimum length specified, or more than two yards less than the length marked on the ticket, shall be considered a defect with respect length. The lot shall be unaccepta
12、ble if two or more rolls in the sample are defective in respect to length; or if the total of the actual length of rolls in the sample is less than the total of the length marked on the ticket 5.3.4 Examination for corndiance with Textile Fiber Products Identification Act. An examination shall be ma
13、de to insure that each roll is labeled for fiber content in accordance with the Textile Fiber Products Identification Act. 6. PACKAGING 6.1 Preservation. packinn. and marking. The preservation, packing, and marking shall be as specified in the contract or purchase order. 3 Provided by IHSNot for Res
14、aleNo reproduction or networking permitted without license from IHS-,-,-A-A-55296 7. NOTES 7.1 Source of Government documena. Copies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 191 1 1-5094 Rules and Regulati
15、ons Under the Textile Fiber Products Identification Act (Copies may be obtained without charge from the Federal Trade Commission, Washington, DC 20580-0001 .) 7.2 Source of non-Government documents ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Mat
16、erials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) AATCC Test Methods (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 122 15, Triangle Park, NC 27709-22 15.) MILITARY INTERESTS: Custodians: Navy - NU Air Force - 99 Army - GL Review Activities: Air Force - 45,82 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: DLA - CT (Project 8305-0522) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
