1、A-A-SS4bSA 9999934 OLb544L 079 Figure 1, configuration A B C D E F G A-A-55465A August 12, 1994 SUPERSEDING October 1, 1993 A-A-55465 Dash number Number of Wire bundle A-A-55465- ci r cui ts diameter range Style I Style II I/ o1 07 2 .O40 - .I90 (1.02 - 5.03)mm - o8 3 .O40 - .I90 (1.02 - 5.03)mm 02
2、09 4 .O40 - .I90 (1.02 - 5.03)mm 03 - 6 .I20 - .650 (3.05 - 16.51)mm 04 - 9 .I20 - .650 (3.05 - 16.51)mm 05 - 12 .I50 - .750 (3.81 - 19.05)mm 06 - 15 .200 - .850 (5.08 - 21.59)mm COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, POWER, SAFETY SHIELD, CLAM SHELL The General Services Administration
3、has authorized the use of this commercial item description (CID). Abstract. This CID covers the general requirements for connector, electrical, power, safety shield. This shield can be used in applications that require crimp to discrete stranded wires, size 14 AWG through 24 AWG. in military systems
4、 needing stringent environmental and electrical requirements. Part or Identifying Number (PIN). Shields covered by this CID are intended for commerciallindustrial applications and shall not be used The PIN for the CID shall be as shown in the following example: T- A-A-55465 - I I l II CID number Das
5、h number Salient characteristics. CID sheet. The electrical connectors shall be in accordance with the requirements specified herein. Desiqn, construction, and dimensions. Design, construction, and dimensions shall be as specified on figure 1 and table 1. Clam shell housings. Clam shell housings sha
6、ll be molded from a nylon material UL 94V-O brick red for high impact and dielectric strength. Operatinq temperature. The operating temperature range shall be from -55C to +105OC. TABLE I. Dimensions and configuration. - I/ Style II does not include insert. AMSC NIA DISTRIBUTION STATEMENT A. Approve
7、d for public release; distribution is unlimited. FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55465A m 74 0365442 TO5 m A-A-55465A 7 STYLE I I WES IK)T INCLUOE INSERT R STYLE I I CNO SCALE3 p- 1 300 -q 230 ,Yb 1 DO STYLE I - NO. 6 X.
8、375 LG. TYPE 8 (2 REO01 PAN HEAO SHEET HETAL SCREUS. SHEET tETAL SCREWS NOT SUPPLIED / INSERT IS ATTACHED TO STRAIN RELIEF. AS AN ADDITIONAL ADJUSTMENT FOR SHALL UIAE BUNDLES, IT SHOULD BE CUT OFF ANO POSITIONEO AS SHOWN BY DOTTED LINES. STYLE II DOES NOT INCLUOE INSERT. Configuration A Figure 1. Di
9、mensions and configurations. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-554b5A 9999974 OLb5443 941 W A-A-55465A -T 1 140 lkqoo 230 NO 6 X 375 LG TYPE (2 REQD PAN HEAD SHEET METAL 5CREWS SHEET METAL SCREWS NOT SUPPLIED ASSEMBLY DETA ILS Con
10、figuration B Figure 1. Dimensions and configurations - Continued. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55465A 9999974 0365444 BAB A-A-55465A I I STYLE II WES NOT INCLUDE INSERT ,425 I o5 STYLE I I CNO SCALE) I- 1.325 I 230 STYLE I NO
11、. 6 X.375 LG. TYPE 8 (2 REODI PAN HEAD SHEET METAL SCREUS. SHEET METAL SCREUS NOT SUPPLIED. r INSERT IS ATTACHED TO STRAIN RELIEF AS AN ADDITIONAL ADJUSTMENT FOR SHALL WIRE BUNDLES. IT SHOULD BE CUT OFF AND POSITIONED AS SHOUN BY DOTTED LINES. TU0 REOUIRED PER CONNECTOR. STYLE II DOES NOT INCLUDE IN
12、SERT. Configuration C Figure 1. Dimensions and configurations - Continued. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55465A 1 r-ll 0.6 r .6zs LG. TYPE e (z REODI - PAN HEAD SHEET HETAL SCREUS. SHEET flETAL SCREWS NOT SUPPLIED. INSERT IS A
13、TTACHED TO STRAIN RELIEF. AS AN ADDITIONAL AOJUSTflENT FOR SHALL WIRE BUNDLES. IT SHOULD BE CUT OFF ANO POSITIONED AS SHOWN BY OOTTEO LINES Q Configuration D Figure 1. Dimensions and configurations - Continued. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
14、om IHS-,-,-A-A-554b5A 9999974 01ib544b b50 m A-A-5546511 I 1 I 1.030 00 -j I- l -I 1.300 N0.6 X .625 LC. TYPE 8 (2 RE001 PAN HEAD SHEET flETAL SCREHS. SHEET HETAL SCREWS NOT SUPPLIEO. INSERT IS ATTACHED TO STRAIN RELIEF. AS AOJUSTflENT FOR SHALL BUNDLES, IT SHOULD POSITIONED AS SHOUN BY DOTTED LINES
15、. AN BE ADDITIONAL CUT OFF AND Configuration E Figure 1. Dimensions and configurations - Continued. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. A-A-55465A 1 .ZED N0.6 X .625 LG. TYPE B (2 REO01 PAN HEAD SHEET METAL SCREUS. SHEET RETAL SCREWS
16、NOT SUPPLIED. iI, INSERT IS ATTACHED TO STRAIN RELIEF. AS AN ADDI ADJUSTMENT FOR SRALL WIRE BUNDLES, IT SHOULD BE OFF AND POSITIONED AS SHOUN BY DOTTED LINES TIONAL CUT Configuration F Figure 1. Dimensions and configurations - Continued. 7 Provided by IHSNot for ResaleNo reproduction or networking p
17、ermitted without license from IHS-,-,-A-A-55465A D 74 OLb5448 423 A-A-SS46SA i 1 530 1 O0 N0.6 X .625 LG. TYPE B (2 REO01 PAN HEAD SHEET METAL SCREHS. SHEET METAL SCREWS NOT SUPPLIED. _ INSERT IS ATTACHED TO STRAIN RELIEF. AS AN ADD1 IT SHOULD BE OFF AND POSITIONED AS SHOWN BY DOTTED LINES. ,ADJUSTH
18、ENT FOR SHALL WIRE BUNDLES, T I ONAL CUT Configuration G Figure 1. Dimensions and configurations - Continued. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-554b5A 9999974 OLb5449 3bT mm 1.27 2.54 5.84 9.53 10.80 12.19 15.88 24.38 26.16 28.96
19、32.51 33.02 33.66 38.86 A-A-55465A Inches 050 .i00 -230 .375 .425 .480 .625 .960 1 .O30 1 .I40 1.280 1.300 1.325 1.530 NOTES: 1. Dimensions are in inches. 2. Millimeters are in parentheses. 3. 4. 5. 6. 7. 8. 9. Unless otherwise specified tolerances shall be t.015 inch (0.38 mm). This item was design
20、ed using inch-pound units of measurement. between the metric and inch-pound units, the inch-pound units shall rule. The insert is attached to the strain relief and is used to provide additional adjustment for small wire bundles or it is discarded. Pictorial representations are for reference purposes
21、 only. Two pan head sheet metal screws are required for assembly, no. 6 x .375 long, not supplied. Detachable insert may separate from strain relief body during shipping. Two strain reliefs are required per connector. In case of problems involving conflicts Figure 1. Dimensions and configurations -
22、Continued. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55Llb5A 9999974 OLb5450 081 = I A-A-55465A Requlatory requirements. Quality assurance provisions. This section is not applicable to this CID. Responsibility for inspection. Unless other
23、wise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection, examination, and test requirements specified herein. his own or any other facilities suitable for the inspection requirements specified herein, unless disapproved by the Government.
24、 examinations, or tests set forth in this description where such inspections, examinations, and tests are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract or purchase order, the contractor may use The Government reserv
25、es the right to perform any of the inspections, Contractor certification statement. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of this CID, and that the product conforms to the producers own drawings, specifications, standards
26、, quality assurances practices, and is the same as the product provided as a bid sample. the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The Government reserves the right to require proof of such conformance prior to Certificate of compliance.
27、 A certificate of compliance must be supplied with all parts supplied to this ID. Packaging. Preservation, packaging, packing, labeling, and marking. Preservation, packaging, labeling, and marking shall be as specified in the contract or purchase order. w. process of procuring the item, but is not m
28、andatory. This section contains relevant information which is useful to buyers, users and suppliers in the Ordering data (see table II). Acquisition documents should specify the following: a. CID document number and revision and CID PIN. b. Quality assurance provisions. c. Packaging requirements. d.
29、 Color (if applicable). Comments. Comments on this CID should be directed to Defense Electronics Supply Center, 1507 Wilmington Pike, ATTN: DESC-ELDI, Dayton, OH 45444-5270, or telephone (513) 296-5391. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
30、,-,-A-A-554bSA m 9999774 0165451 TL8 m Suggested sources of supply 1 CID PIN Vendor CID PIN Vendor Vendor CAGE A-A-55465- 11 commercial PIN A-A-55465- I/ commercial PIN number Style I Style II (no insert) o1 640713-1 07 64071 3-2 00779 _ - 08 641945-1 00779 02 641776-1 09 641776-2 00779 _ 00779 03 6
31、4071 5-1 -_- 04 640716-1 - - 00779 _- 00779 o5 64071 7-1 _ o6 640718-1 - - 00779 - A-A-55465A sources of supply. A suggested source of supply is listed in table II. Additional sources will be added as they become available. TABLE II. Ordering data. Vendor CAGE number 00779 Vendor name and address AMP, Incorporated P.O. Box 3608 Harrisburg, PA 17105-3608 CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE PREPARING ACTIVITY: OLA-ES (Project 5935-0522) 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
