1、A-A-554b7A m 9999974 O365202 5b7 A-A-55467A August 12, 1994 SUPERSEDING A-A-55467 October 1, 1993 COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, POWER, CRIMP TO WIRE, SPLIT PIN The General Services Administration has authorized the use of this commercial item description (CID). Abstract. power,
2、 crimp to wire, split pin. This pin can be used in applications that require crimp to discrete stranded wires, size 14 AWG through 24 AWG. applications and shall not be used in military systems needing stringent environmental and electrical requirements. Part or Identifying Number (PIN). This commer
3、cial item description (CID) covers the general requirements for connector, electrical, Pins covered by this CID are intended for commercial/industrial The PIN for the CID shall be as shown in the following example: o1 A-A-55467 - - I I I I II CID number Dash number Salient characteristics. CID sheet
4、. Design, construction, and dimensions. The electrical connectors shall be in accordance with the requirements specified herein. Design, construction, and dimensions shall be as specified on figure 1. Operating temperature. Contact material. Plating. The operating temperature range shall be from -55
5、C to t105“C. The contact material shall be brass or phosphor bronze. Plating shall be pre-tin or .76 microns (30 microinches) minimum localized gold in contact area, over 1.27 microns (50 microinches) minimum of nickel. Matinq force. Unmatinq force. Contact insertion. Contact retention. Crimp tensil
6、e strength. Connector mating force shall not exceed 6.67 newtons (1.5 pounds). Connector unmating force shall not exceed 2.22 newtons (0.5 pound) minimum. Contact insertion force shall be 8.90 newtons (2 pounds) maximum per contact. Contact retention force shall be 66.72 newtons (15 pounds) minimum.
7、 The crimp tensile strength of the wire-to-contact termination shall not be less than the value specified in table I when tested at a cross-head parting speed of 25.4 millimeters (1 inch) per minute, maximum. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
8、FSC 5935 Licensed by Information Handling Services A-A-55467A 9999974 0165203 4T3 = A-A-55467A CUT-OFF TAB WIDTH DETAIL D O07 MAX R 3 shocks in each direction applied along the three mutually perpendicular planes, total 18 shocks. resistance, dry circuit not to exceed 6.0 milliohms. The contacts sha
9、ll evidence no discontinuity greater than 10 microseconds and the termination Thermal shock. The connector, when mated, shall be subjected to 25 cycles between -55OC and +85OC, dielectric withstanding voltage; 3.75 milliohms maximum termination resistance, dry circuit. The connector, when mated, sha
10、ll be subjected to temperature-humidity cycling between +25OC and +65OC at 95 percent RH, with cold shock at -10C during any 5 of the first 9 cycles. Durability. termination resistance, dry circuit shall not exceed 3.6 milliohms. physical damage. Temperature-humidity cycling. Durability shall consis
11、t of 50 cycles of mating and unmating and upon completion the There shall be no indication of Corrosion. Corrosion shall be 48 hours at 5 percent salt concentration. After exposure of the mated and unmated connectors, the termination resistance, dry circuit will not exceed 7.0 milliohms. Loose piece
12、 and strip form ordering data. Loose piece and strip form ordering data shall be as specified in tables III and IV. Regulatory requirements. Quality assurance provisions. This section is not applicable to this CID. Responsibility for inspection. Unless otherwise specified in the contract or purchase
13、 order, the contractor is responsible for the performance of all inspection, examination, and test requirements specified herein. his own or any other facilities suitable for the inspection requirements specified herein, unless disapproved by the Government. examinations, or tests set forth in this
14、description where such inspections, examinations, and tests are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract or purchase order, the contractor may use The Government reserves the right to perform any of the inspect
15、ions, Contractor certification statement. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of this CID, and that the product conforms to the producers own drawings, specifications, standards, quality assurances practices, and is the
16、 same as the product provided as a bid sample. the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The Government reserves the right to require proof of such conformance prior to Certificate of compliance. A certificate of compliance shall accompa
17、ny all parts supplied to this CID. Packaging. Preservation, packaging, packing, labelincl, and marking. Preservation, packaging, labeling, and marking shall be as specified in the contract or purchase order. 6 Licensed by Information Handling Services A-A-55467A 9999974 0365208 T85 W A-A-55467-06 A-
18、A-55467-07 A-A-55467-08 A-A-55467-09 A-A-55467A 350705-7 C 20-1 4 Brass Gold 2/ Nickel 00779 350707-1 C 20-14 Brass Pre-t i n - 00779 350707-2 C 20-14 Brass Gold I/ Nickel 00779 350707-7 C 20-14 Brass Gold 2/ Nickel 00779 w. process of procuring the item, but is not mandatory. This section contains
19、relevant information which is useful to buyers, users and suppliers in the Ordering data. Acquisition documents should specify the following: a. CID document number and revision and CID PIN. b. Quality assurance provisions. c. Packaging requirements. d. Color (if applicable). Comments. Comments on t
20、his CID should be directed to Defense Electronics Supply Center, 1507 Wilmington Pike, ATTN: DESC-ELDI Dayton, OH 45444-5270, or telephone (513) 296-5391. A suggested source of supply is listed in table IV. Sources of supply. Additional sources will be added as they become available. TABLE IV. Split
21、 pin loose piece ordering data. 7 Licensed by Information Handling Servicest I A-A-55467A 9999974 0165209 911 A-A-55467A Table IV. Suggested sources of supply - continued. Vendor CAGE Number 00779 00779 00779 00779 00779 00779 00779 00779 00779 00779 00779 00779 - I/ Plated with 30 microinches c.76
22、microns) minimum of gold in mating area and inside wire barrel over 50 microinches (1.27 microns) minimum nickel underplate on entire contact. - 2/ Gold plated with 30 microinches C.76 microns) minimum in mating area over 50 microinches (1.27 microns) minimum nickel underplate on entire contact. Ven
23、dor CAGE number 00779 8 Vendor name and address AMP, Incorporated P.O. Box 3608 Harrisburg, PA 17105-3608 Licensed by Information Handling Servicesn . - -_ _-_ A-A-55467A W 9997974 Olb5210 633 W A-A-55467A Supersession data. Supersession data shall be as specified in table V. TABLE V. Supersession data. CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE PREPARING ACTIVITY: DLA-ES (Project 5935-D524) 9 Licensed by Information Handling Services
