1、 INCHPOUND AA55563/27A 27 November 2013 Superseding AA55563/27 17 October 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CLOSED ENDED, WITH 2 MOUNTING HOLES, FOR USE WITH HEAT SINKS The General Services Administration has authorized the use of this co
2、mmercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of commercial item description (CID) AA55563. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This CID s
3、pecification sheet uses a classification system which is included in the PIN as shown in the following example (see notes). AA55563 CID number /27 Applicable CID specification sheet Material H Card holder width/ board thickness XX Length formerly 1/4 HT), or “D“ (stainless steel). The material type
4、designator and shall be included in the PIN. Material thickness. The beryllium copper thickness shall be .008 .002 inch (0.20 0.05 mm). Card holder width/board thickness. The card holder width/board thickness is variable and based on the distance the card guide is mounted from the heat sink side wal
5、l (see figure 1). To obtain optimum clamping force, the centerline of the card guide installation holes in the heat sink shall be spaced .105 inch (2.67 mm) plus the thickness of the circuit card assembly printed board thickness from the side wall. The applicable card holder width/board thickness de
6、signator for this CID specification sheet is “H“. Overall length. Overall length is shown on figure 1 as dimension “L“, and is displayed in table I herein. Applicable overall length designator “10“, “15“, “20“, “25“, “30“, “35“, “40“, “45“, “50“, “55“, or “60“ shall be included in the PIN. Finish. F
7、inish types shall be defined in AA55563. Applicable finish materials designator “C“ (copper plate), “D“ (black ebonal), “E“ (gold plate), “F“ (nickel plate), “H“ (silver plate), “J“ (zinc, yellow chromate), “K“ (no finish), or “R“ (zinc, clear chromate) are available for material type designators “A
8、“ and “B“. Finish designator “G“ (passivate) is the only finish available for material type designator “D“. The finish designator shall be included in the PIN. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/27A 2 Mounting ho
9、le spacing. Mounting hole spacing is shown on figure 1 as dimension “M“. Dimension “M“ is listed in table I herein. Inches mm Inches mm Inches mm Inches mm .003 .005 .020 0.08 0.13 0.51 .067 .08 .105 1.70 2.03 2.67 .156 .160 .180 3.96 4.06 4.57 .198 .250 .500 5.03 6.35 12.7 NOTES: 1. Dimensions are
10、in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm), for 3 places. FIGURE 1. Card holder design and dimensions. Provided by IHSNot for ResaleNo reproduction or networ
11、king permitted without license from IHS-,-,-AA55563/27A 3 TABLE I. Length and hole spacing. 1/ 2/ PIN designator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (0.13) 10 1.0 (25) .50 (13) 15 1.5 (38) 1.0 (25) 20 2.0 (51) 1.5 (38) 25 2.5 (64) 2.0 (51) 30 3.0 (76) 2.5 (64) 35 3.5 (89)
12、 3.0 (76) 40 4.0 (102) 3.5 (89) 45 4.5 (114) 4.0 (102) 50 5.0 (127) 4.5 (114) 55 5.5 (140) 5.0 (127) 60 6.0 (152) 5.5 (140) 1/ Dimensions are in inches. Millimeters are given for general information only. 2/ Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010
13、 inch (0.25 mm) for three place decimals. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. AA55563 Source of documents. Commercial Item Description AA55563 Holder, Electrical
14、Card, Metal Card Guide, General Requirements for. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be
15、 as specified in AA55563. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known
16、 to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Man
17、ufacturer contact information 61081 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 URL: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
18、HS-,-,-AA55563/27A 4 Part number (P/N) supersession data. These CID specification sheet PINs supersedes the following manufacturers P/Ns as shown in table II. The CID PINs listed in table II cover the different lengths available. This information is being provided to assist in reducing proliferation
19、 in the Government inventory system. TABLE II. Commercial part number supersession data. CID PIN; AA55563/27HXX& 1/ Manufacturers 2/ Material type Card holder width/board thickness Overall length Finish CAGE 61081 4/ A H 10 3/ 376B2P A H 15 3/ 376B3P A H 20 3/ 376B4P A H 25 3/ 376B5P A H 30 3/ 376B6
20、P A H 35 3/ 376B7P A H 40 3/ 376B8P A H 45 3/ 376B9P A H 50 3/ 376B10P A H 55 3/ 376B11P A H 60 3/ 376B12P B H 10 3/ 376BH2P B H 15 3/ 376BH3P B H 20 3/ 376BH4P B H 25 3/ 376BH5P B H 30 3/ 376BH6P B H 35 3/ 376BH7P B H 40 3/ 376BH8P B H 45 3/ 376BH9P B H 50 3/ 376BH10P B H 55 3/ 376BH11P B H 60 3/ 3
21、76BH12P D H 10 G 376CR2 D H 15 G 376CR3 D H 20 G 376CR4 D H 25 G 376CR5 D H 30 G 376CR6 D H 35 G 376CR7 D H 40 G 376CR8 D H 45 G 376CR9 D H 50 G 376CR10 D H 55 G 376CR11 D H 60 G 376CR12 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
22、se from IHS-,-,-AA55563/27A 5 TABLE II. Commercial part number supersession data Continued. 1/ See classification/Part Identification Number for symbol representation. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time
23、of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “C“, “D“, “E“, “F“, “H“, “J“, “K“, or “R“ are a
24、vailable for this material type. 4/ Manufacturer CAGE 61081 superseded part number suffix letter “P“ denotes finish material. Guidance on use of alternative parts with less hazardous or nonhazardous materials. This CID specification sheet provides for a number of alternative plating materials via th
25、e PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. Changes from previous issue. Asterisks are not used in this revision to identify changes with respect to the previous revision, due to the extensiveness of t
26、he changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS: Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Review activity: Project: 59982012057 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
