1、INCHPOUND AA55563/29A 29 November 2013 Superseding AA55563/29 14 November 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, NARROW PROFILE, CENTER MOUNT, WITH FLARED ENTRY, WITH 2 MOUNTING HOLES The General Services Administration has authorized the use
2、of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of commercial item description (CID) AA55563. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN).
3、This CID specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /29 Applicable CID specification sheet Material # Card holder width/ board thickness (see table I) XX Length (see tabl
4、e II) formerly 1/4 HT). The material type designator and shall be included in the PIN. Material thickness. The material thickness shall be .006 .002 inch (0.15 0.05 mm). Card holder width/board thickness. The card holder width/board thickness shall be defined in table I herein and is shown on figure
5、 1 as dimensions “A“ and “B“. The applicable card holder width/board thickness designators for this CID specification sheet are also used to designate mounting hole size as specified in table I. Overall length. Overall length is shown on figure 1 as dimension “L“, and is displayed in table II herein
6、. Applicable overall length designator “10“, “15“, “20“, “25“, “30“, “35“, “40“, “45“, “50“, “55“, or “60“ shall be included in the PIN. Finish. Finish types shall be defined in AA55563. Applicable finish materials designator “C“ (copper plate), “E“ (gold plate), “F“ (nickel plate), “H“ (silver plat
7、e), “J“ (zinc, yellow chromate), “K“ (no finish), or “R“ (zinc, clear chromate) are available for material type designators “A“ and “B“. The finish designator shall be included in the PIN. Mounting hole spacing. Mounting hole spacing is shown on figure 1 as dimension “M“. Dimension “M” is listed in
8、table I herein. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/29A 2 Inches mm Inches mm Inches mm Inches mm .003 .005 .02 0.08 0.13 0.51 .03 .04 0.76 1.02 .067 .100 1.70 2.54 .125 .130 .250 3.18 3.30 6.35 NOTES: 1. Dimensio
9、ns are in inches. Millimeters are given for information only. 2. Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 1. Card holder design and dimensions. TABLE I. Card holder configurations and dimensions. 1/ P
10、IN designator for card holder width/ board thickness Dimension “B“ 2/ Dimension “D“ 2/ Dimension “E“ 2/ Inches mm Inches mm Inches mm M .031 0.79 .190 4.83 .095 2.42 P .063 1.60 .190 4.83 .095 2.42 T .094 2.39 .200 5.08 .100 2.54 W .125 3.18 .210 5.33 .105 2.67 1/ See figure 1. Millimeters are given
11、 for information only. 2/ Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/29A 3 TABLE II. Length and hole sp
12、acing. 1/ 2/ PIN designator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (0.13) 10 1.0 (25) .750 (19.1) 15 1.5 (38) 1.25 (31.8) 20 2.0 (51) 1.75 (44.5) 25 2.5 (54) 2.25 (57.2) 30 3.0 (76) 2.75 (69.9) 35 3.5 (89) 3.25 (82.6) 40 4.0 (102) 3.75 (95.3) 45 4.5 (114) 4.25 (108.0) 50 5.0
13、 (127) 4.75 (120.7) 55 5.5 (140) 5.25 (133.4) 60 6.0 (152) 5.75 (146.1) 1/ Dimensions are in inches. Millimeters are given for information only. 2/ Unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. NOTES. PIN. The PI
14、N should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA55563 Holder, Electrical Card, Metal Card Guide, General Requirements For. (Copies of these d
15、ocuments are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA55563. Commercial products. As part of the market
16、 analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of thi
17、s CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Birtcher A Division of Pentair T
18、echnical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 URL: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/29A 4 Part number (P/N) supersession data. These CID
19、specification sheet PINs supersede the following manufacturers P/Ns in table III as shown. The CID PINs listed in table III cover the different lengths available. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part num
20、ber supersession data. CID PIN; AA55563/29#XX& 1/ Manufacturers 2/ Material type Card holder width/board thickness Overall length Finish CAGE 61081 4/ A M, P, T, or W 10 3/ 21BT2F A M, P, T, or W 15 3/ 21BT3F A M, P, T, or W 20 3/ 21BT4F A M, P, T, or W 25 3/ 21BT5F A M, P, T, or W 30 3/ 21BT6F A M,
21、 P, T, or W 35 3/ 21BT7F A M, P, T, or W 40 3/ 21BT8F A M, P, T, or W 45 3/ 21BT9F A M, P, T, or W 50 3/ 21BT10F A M, P, T, or W 55 3/ 21BT11F A M, P, T, or W 60 3/ 21BT12F B M, P, T, or W 10 3/ 21BHT2F B M, P, T, or W 15 3/ 21BHT3F B M, P, T, or W 20 3/ 21BHT4F B M, P, T, or W 25 3/ 21BHT5F B M, P,
22、 T, or W 30 3/ 21BHT6F B M, P, T, or W 35 3/ 21BHT7F B M, P, T, or W 40 3/ 21BHT8F B M, P, T, or W 45 3/ 21BHT9F B M, P, T, or W 50 3/ 21BHT10F B M, P, T, or W 55 3/ 21BHT11F B M, P, T, or W 60 3/ 21BHT12F 1/ See classification Part/Identification Number for symbol representations. 2/ The manufactur
23、ers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking parag
24、raph of AA55563. 3/ Finish materials designator “C“, “D“, “E“, “F“, “H“, “J“, “K“, or “R“ are available for this material type. 4/ Manufacturer CAGE 61081 superseded part number the series type is “21“, the letters “B“ or “BH“ denotes material type, the letter “T“ denotes card holder width/board thi
25、ckness, the numbers “4“ through “12“ denotes card holder lengths, and the letter “F“ denotes finish material. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/29A 5 Guidance on use of alternative parts with less hazardous or nonhazardous mater
26、ials. This CID specification sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. Changes from previous issue. Asterisks are not used in this r
27、evision to identify changes with respect to the previous revision, due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Review activity: Project 59982012059 Air Force 99 NOT
28、E: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
