1、INCHPOUND AA55563D 13 August 2013 SUPERSEDING AA55563C 9 March 2007 COMMERCIAL ITEM DESCRIPTION HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, GENERAL REQUIREMENTS FOR The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This
2、Commercial Item Description (CID) covers the general requirements for a family of metal card guides (hereafter referred to as card holders) intended for use to guide and hold circuit card assemblies into their installed positions. Card holders covered by this CID are for moderate heat transfer and v
3、ibration applications. Requirements for specific card holders are covered in the individual CID specification sheets. Card holders covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system whi
4、ch is included in the Part Identification Number (PIN) as shown in the following example (see 7.1). AA55563 CID number /30 Applicable CID specification sheet * Material (see 3.3 and table I) * Card holder width /board thickness (see 3.4) * * Length (see 3.5 and table II) * Finish (see 3.6 and table
5、III) 3. SALIENT CHARACTERISTICS. 3.1 CID specification sheet. The family of card holders for use on circuit card assemblies shall be in accordance with the requirements specified herein and the applicable CID specification sheet. In the event of conflict between this general CID and the applicable C
6、ID specification sheet, the latter shall govern. 3.2 Interface and physical dimensions. Card holders shall be as specified herein and in the applicable CID specification sheet. NOTE: Tolerances, unless otherwise specified, tolerances are .02 inch (0.5 mm) for two place decimals and .010 inch (0.25 m
7、m) for three place decimals. 3.3 Materials. The materials used shall be as specified herein and the applicable CID specification sheet. Materials not specified herein or in the CID specification sheet shall be of the same quality used for the intended purpose in best commercial practices (see sectio
8、n 4). Suitable protection against galvanic corrosion shall be provided when dissimilar metals are used. 3.3.1 Beryllium copper, temper TD01 (formerly 1/4 H). Beryllium copper of temper TD01 material shall be as defined in ASTM B194, or equivalent. Card holders constructed of beryllium copper of temp
9、er TD01 shall include a suffix “A“ in the PIN. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAC, Post Office Box 3990, Columbus, OH 432183990, or facsimile (614) 6931642, o
10、r electronic mail 5998.Documentsdla.mil. Since contact information can change, you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
11、se from IHS-,-,-AA55563D 2 3.3.2 Beryllium copper temper TH01, heat treated (after forming) (formerly 1/4 HT). Heat treated beryllium copper of temper TH01 material shall be as defined in ASTM B194, or equivalent. Card holders constructed of heat treated beryllium copper shall include a suffix “B“ i
12、n the PIN. 3.3.3 Steel. Steel shall be as defined in ASTM A684/A684M, or equivalent. Card holders constructed of steel shall include a suffix “C“ in the PIN. 3.3.4 Stainless steel SAE 30301 (formerly type 301, condition quarter hard). Stainless steel SAE 30301 shall be as defined in SAE AMS 5517, or
13、 equivalent. Card holders constructed of stainless steel SAE 30301 shall include a suffix “D“ in the PIN. 3.3.5 Stainless steel 1/2 H (half hard). Stainless steel 1/2 H shall be as defined in ASTM A240/A240M or equivalent. Card holders constructed of stainless steel 1/2 H shall include a suffix “E“
14、in the PIN. 3.3.6 Stainless steel full H (full hard). Stainless steel full H shall be as defined in SAE AMS 5519, SAE AMS 5906, or equivalent. Card holders constructed of stainless steel full H shall include a suffix “F“ in the PIN. 3.3.7 Phosphor bronze. Phosphor bronze shall be as defined in ASTM
15、B103/B103M or ASTM B139/B139M, or equivalent. Card holders constructed of phosphor bronze shall include a suffix “G“ in the PIN. TABLE I. Card holder material. Material designator Material type Applicable specification Paragraph A B C D E F G Beryllium copper of temper TD01 Beryllium copper of tempe
16、r TH01 Steel (cold rolled) Stainless steel 1/4 H (SAE 30301) Stainless steel 1/2 H Stainless steel full H Phosphor bronze ASTM B194, temper TD01 ASTM B194, temper TH01 ASTM A684/A684M SAE AMS 5517 ASTM A240/A240M SAE AMS 5519, SAE AMS 5906 ASTM B103/B103M or ASTM B139/B139M 3.3.1 3.3.2 3.3.3 3.3.4 3
17、.3.5 3.3.6 3.3.7 3.4 Card holder width/board thickness or configuration. Card holder width/board thickness or configuration shall be as specified in the applicable CID specification sheet. The card holder width/board thickness or configuration designator(s) from the applicable CID specification shee
18、t shall be included in the PIN. 3.5 Overall length. Unless otherwise specified in the applicable CID specification sheet, overall length shall be as defined in table II. Overall length designator from table II shall be included in the PIN. 3.6 Finish. Unless otherwise specified in the applicable CID
19、 specification sheet, finish shall be as defined in table III. Finish designator from table III shall be included in the PIN. 3.6.1 Cadmium, yellow chromate (see 7.6 and 7.6.1). Cadmium yellow chromate finish shall be as defined in SAE AMSQQP416, type II, class 2, or equivalent. Cadmium yellow chrom
20、ate finish parts shall include a suffix “A“ in the PIN. 3.6.2 Cadmium, clear chromate (see 7.6 and 7.6.1). Cadmium clear chromate finish shall be as defined in SAE AMSQQP416, type II, class 2, or equivalent. Cadmium clear chromate finish parts shall include a suffix “B“ in the PIN. 3.6.3 Copper. Cop
21、per plate finish shall be as defined in SAE AMS 2418, or equivalent. Copper plate finish parts shall include a suffix “C“ in the PIN. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563D 3 TABLE II. Overall length. Length designator Card holder o
22、verall length dimension “L“ 1/ Inches (mm) Length designator Card holder overall length dimension “L“ 1/ Inches (mm) 10 15 20 25 30 1.0 1.5 2.0 2.5 3.0 (25) (38) (51) (64) (76) 60 65 70 75 80 6.0 6.5 7.0 7.5 8.0 (152) (165) (178) (191) (203) 35 40 45 50 55 3.5 4.0 4.5 5.0 5.5 (89) (102) (114) (127)
23、(140) 85 90 95 A0 A5 8.5 9.0 9.5 10.0 10.5 (216) (229) (241) (254) (267) 1/ See the applicable CID specification sheet for the actual lengths used. 3.6.4 Ebonal, black. Black ebonal finish shall be as defined in MILF495, or equivalent. Black ebonal finish parts shall include a suffix “D“ in the PIN.
24、 3.6.5 Gold plate. Gold plate finish shall be as defined in ASTM B488, or equivalent. Gold plate finish parts shall include a suffix “E“ in the PIN. 3.6.6 Nickel, electrodeposited. Electrodeposited nickel finish shall be as defined in SAE AMSQQN290, class 1, grade G, bright, or equivalent. Electrode
25、posited nickel finish parts shall include a suffix “F“ in the PIN. 3.6.7 Passivate (stainless steel only). Passivate cleaning of stainless steel shall be as defined in ASTM A967, or equivalent. Passivate cleaning of stainless steel parts shall include a suffix “G“ in the PIN. 3.6.8 Silver. Silver fi
26、nish shall be as defined in ASTM B700, type 3, grade A (mat), or equivalent. Silver finish parts shall include a suffix “H“ in the PIN. 3.6.9 Zinc, clear chromate. Zinc clear chromate finish shall be as defined in ASTM B633 Fe/Zn 8, or equivalent. Zinc clear chromate finish parts shall include the s
27、uffix “R“ in the PIN. 3.6.10 Zinc, yellow chromate. Zinc yellow chromate finish shall be as defined in ASTM B633. Zinc yellow chromate plate finish parts shall include the suffix “J“ in the PIN. 3.6.11 No finish. No finish option parts shall include the suffix “K“ in the PIN. 3.6.12 Nickel. electrol
28、ess. Electroless nickel finish shall be as defined in ASTM B733, SAE AMS 2404, or equivalent. Electroless nickel finished parts shall include a suffix “N“ in the PIN. 3.7 Marking. Card holders supplied to this CID shall be marked with the manufacturers standard commercial PIN. The part number marked
29、 on the unit pack shall be the CID PIN. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirement
30、s, and promotes economically advantageous life cycle costs. 3.9 Workmanship. Card holders shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance.Provided by IHSNot for ResaleNo reproduction or networki
31、ng permitted without license from IHS-,-,-AA55563D 4 TABLE III. Card holder finishes. Finish designator Finish Applicable specification (or equivalent) Paragraph A Cadmium, yellow chromate SAE AMSQQP416, type II, class 2 3.6.1 B Cadmium, clear chromate SAE AMSQQP416, type II, class 2 3.6.2 C Copper
32、SAE AMS 2418 3.6.3 D Ebonal, black MILF495 3.6.4 E Gold ASTM B488 3.6.5 F Nickel, electrodeposited SAE AMSQQN290, class I, grade G, bright 3.6.6 G Passivated steel ASTM A967, SAE AMS 2700 3.6.7 H Silver ASTM B700 3.6.8 R 1/ Zinc, clear chromate ASTM B633, Fe/Zn 8 3.6.9 J Zinc, yellow chromate ASTM B
33、633, Fe/Zn 8 3.6.10 K No finish 3.6.11 N Nickel, electroless ASTM B733, SAE AMS 2404 3.6.12 1/ PIN designator “I“ superseded by designator “R“. 4. REGULATORY REQUIREMENTS. 4.1 Recycled/recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practica
34、ble, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, quality assurances pract
35、ices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this CID. a. The
36、company producing the item must have been producing a product meeting the requirements of this CID for at least 24 months. b. The company producing the item must have sold 250 units meeting the requirements of this CID in the commercial marketplace over the past 24 months. 5.3 Inspection requirement
37、s. Inspection and acceptance of material shall be in accordance with the requirements cited in the contract or purchase request. 5.4 Certificates of compliance. Each manufacturer desiring to be listed as a suggested source of supply (see applicable CID specification sheet) shall submit a DLA Land an
38、d Maritime certificate of compliance to DLA Land and Maritime VAC. This certificate shall state that the manufacturers product meets all the requirements of this CID and the applicable CID specification sheet. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or
39、order. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563D 5 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for of PIN format example. 7.2 Commercial and Government Entity
40、(CAGE) code. For ordering purposes, inventory control, and submission of these card holders to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.3 Source of documents. DEPARTMENT OF DEFENSE SPECIFICATION MILF495 Finish, Chemical, Black
41、, For Copper Alloys. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) FEDERAL REGULATIONS FAR Federal Acquisition Regulations (FAR) (Co
42、pies of these documents are available online at http:/www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.) ASTM INTERNATIONAL (ASTM) ASTM B103/B103M Standard Specification for Phosphor Bronze Plate, Sheet, Strip An
43、d Rolled Bar. ASTM B139/B139M Standard Specification for Phosphor Bronze Rod, Bar, and Shapes. ASTM B194 Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip And Rolled Bar. ASTM A240/A240M Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Str
44、ip for Pressure Vessels and for General Applications. ASTM B488 Standard Specification for Electrodeposited Coating of Gold for Engineering Uses. ASTM B633 Standard Specification for Electrodeposited Coatings of Zinc On Iron and Steel. ASTM A684/A684M Standard Specification for Steel, Strip, High-Ca
45、rbon, Cold-Rolled. ASTM B700 Standard Specification for Electrodeposited Coatings of Silver for Engineering Use. ASTM B733 Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal. ASTM A967 Standard Specification for Chemical Passivation Treatments for Stainless St
46、eel Parts. (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 194282959.) SAE INTERNATIONAL (SAE) SAE AMSQQN290 Nickel Plating (Electrodeposited). SAE AMSQQP416 Plating, Cadmium (Electrodep
47、osited). SAE AMS 2404 Electroless Nickel Coatings. SAE AMS 2418 Plating, Copper. SAE AMS 2700 Passivation of Corrosion Resistant Steels. SAE AMS 5517 Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 125 ksi (862 MPa) Tensile Strength. SAE AMS 5519 Steel, Corrosion Resi
48、stant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 185 ksi (1276 MPa) Tensile Strength. SAE AMS 5906 Steel, Corrosion Resistant, Sheet Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled, Full Hard, 185 ksi (1276 MPa) Tensile Strength. (Copies of these documents are available online at http:/www.sae.org or from the SAE World Headquaters, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563D 6 7.4 Ordering data. The contract or order should spec
