1、AMSC N/A FSC 5920 INCH-POUND A-A-55570/2C 19 April 2012 SUPERSEDING A-A-55570/2B 13 March 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET FUSEHOLDER, EXTRACTOR POST, IN-LINE CRIMP TYPE, ACCOMMODATES MINIATURE, AUTOMOTIVE BLADE TYPE, INCLOSED LINK FUSES. The General Services Administration has a
2、uthorized the use of this commercial item description for all federal agencies. The complete requirements for procuring fuseholders described herein shall consist of this document and the issue in effect of A-A-55570. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item descripti
3、on (CID) specification sheet uses a classification system that is included in the PIN as shown in the following example (see NOTES). AA55570 /02 - 001 CID number Applicable CID specification sheet (two digits) Dash number (see table I) SALIENT CHARACTERISTICS. Interface and physical dimensions. Fuse
4、holders supplied to this CID specification sheet shall be as specified herein (see figure 1). Ampere rating. The ampere rating shall be as specified in table I. Voltage rating. The voltage rating shall be 32 V dc. Fuseholder body material. The fuseholder body material shall be black thermoplastic. T
5、erminal plating. Terminals shall be tin plated copper alloy. Use of pure tin plating is prohibited as a final finish and as an undercoat. Use of tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. Operating temperature. The operating temperature shall be -40
6、C to +105C. Crimping tool. A standard crimping tool may be used to crimp the matted area to secure wire. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55570/2C 2 NOTES: 1. Dimensions are in inches. 2. Tolerance is .005 inch (0.13 mm), unless ot
7、herwise specified. FIGURE 1. Configuration and dimensions. Inches mm .25 6.35 .45 11.43 .67 17.02 1.00 25.40 2.07 52.58 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55570/2C 3 TABLE I. Electrical characteristics. CID dash number AA55570/02- Am
8、pere rating Terminals Fuse accommodation 001 20 amperes maximum Terminals will accept #16 - 22 AWG standard wire. 1/ Accommodates CID AA55569/02-001 through AA55569/02-008 fuses 002 30 amperes maximum Terminals will accept #10 - 14 AWG standard wire. 2/ Accommodates CID AA55569/02-009 through AA5556
9、9/02-010 fuses 1/ Use appropriate wire size based on the fuse used. For example, use #16 AWG wire for 20 A fuse. 2/ Use appropriate wire size based on the fuse used. For example, use #10 AWG wire for 30 A fuse. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to
10、this CID specification sheet. See the classification section for PIN format example. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet p
11、reparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers
12、shown.) MFRs CAGE MFRs name and address 75915 Littelfuse Incorporated 8755 W. Higgins Road; Suite 500 Chicago, IL 60631-2708 Phone number (800) 999-9445 Facsimile number (847) 391-0753 E-mail: mailto: Uniform Resource Locator (URL): http:/ Provided by IHSNot for ResaleNo reproduction or networking p
13、ermitted without license from IHS-,-,-A-A-55570/2C 4 Part number (P/N) supersession data. These CID specification sheet part numbers supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. P/N s
14、upersession data. CID dash number AA55570/02- (see table I) MFRs CAGE MFRs P/N 1/ 001 75915 153002 002 75915 153003 1/ The manufacturers P/N shall not be used for acquisition to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforemen
15、tioned commercial products were reviewed and could be replaced by the CID P/N shown. For actual part marking requirements, see the marking paragraph of A-A-55570. . Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue du
16、e to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2012-021 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
