1、ASMC N/A FSC 5340 A-A-55592B 27 August 2010 SUPERSEDINGA-A-55592A 31 October 1997 COMMERCIAL ITEM DESCRIPTION HINGE, BUTT, CONTINUOUS (PIANO) .060 THICKNESS, .125 PIN DIA The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE
2、 This Commercial Item Description (CID) covers commercial and industrial quality, continuous butt piano hinges suitable for use on cases, chests, and any other adaptable surface. 2. SALIENT CHARACTERISTICS. 2.1 Butt hinges and pin hinge furnished under this CID shall conform to the dimensions as sp
3、ecified in Table I and Figure 1 below. FIGURE 1. HINGE. TABLE I. DASH NUMBERS AND DIMENSIONS WIDTH KNUCKLE PITCH KNUCKLE PIN STOCK DASH No. A REF B .031 LENGTH D 1/ P 2/ +.015 -.003 F +.007 -.001 G LENGTH L .03 9 10 11 12 13 14 15 16 1.062 1.500 2.000 2.500 1.062 1.500 2.000 2.500 .531 .750 1.000 1.
4、250 .531 .750 1.000 1.250 .623 +.000 -.010 1.250 .130 .125 .002 85.00 SEE SAL. CHAR. 2.6 .998 +.000 -.015 2.000 84.00 SEE SAL. CHAR. 2.6 17 - - - - - 1/ SEE SAL. CHAR. 2.4 2/ SEE SAL. CHAR. 2.5 G (SEE NOTE 6.3) G (SEE NOTE 6.3) Comments, suggestions, or questions on this document should be addressed
5、 to Defense Supply Center Philadelphia, ATTN: DSCP-NASA, 700 Robbins Avenue., Philadelphia, PA 19111-5096 or e-mail to dscpg&ispecommentsdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.da
6、ps.dla.mil. 275 MIN OPENING .030 MAX .060 .005 FL A B D P IMPRESS PART IDENTIFICATION NUMBER AT A MAXIMUM OF 5 INCH INTERVALS INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55592B 2 2.2 MATERIAL: A. Aluminum leaf temper, H24 or H34 Al
7、loy 5052 (UNS A95052) in accordance with SAE-AMS-QQ-A-250/8. Aluminum pin temper, H34 Alloy 5052 (UNS A95052) in accordance with ASTM B211. B. Brass leaf alloy 268 (UNS C26800) temper HO2, in accordance with ASTM B36/B36M. Copper pin alloy 260 (UNS C26000) temper HO2, in accordance with ASTM B134/B1
8、34M. C. Corrosion resistant steel leaf, temper annealed composition 301 (UNS S30100) in accordance with ASTM A666, 302 ( UNS S30200) or 304 (UNS S30400) in accordance with ASTM A240/A240M. Corrosion resistant steel pin, composition 302 (UNS S30200), 304 (UNS S30400), 305 (UNS S30500) and 316 ( UNS S
9、31600) in accordance with ASTM A313/A313M. D. Carbon steel leaf cold rolled, temper no. 4 in accordance with QQ-S-698. Carbon steel pin composition 1010 (UNS G10100), 1020 (UNS G10200),. in accordance with ASTM A853. E. Carbon steel leaf cold rolled, temper no. 4 in accordance with QQ-S-698. Copper
10、pin alloy 260 (UNS C26000), temper HO2 in accordance with ASTM B134/B134M. 2.3 FINISH: Material A, B and D shall be plain (uncoated). When specified, material A shall be chemical conversion coated in accordance with MIL-DTL-5541, class 1A, and material D shall be zinc plated in accordance with ASTM
11、B633, TYPE II, FE/ZN 13. Material C shall be passivated in accordance with SAE-AMS-QQ- P-35. Material E shall be cadmium plated in accordance with SAE-AMS-QQ-P-416, Type II, Class 1. 2.4. Knuckles: End knuckles shall be a minimum of 1/2 of knuckle. 2.5 Pitch: Cumulative tolerance on pitch is +.015 i
12、nches in any 36 inch segment. 2.6 Hinges shall be stocked and issued in lengths of 84.00 or 85.00 inches as specified. Application may be of any length within the above length. 2.7 Workmanship. The hinges furnished shall be free from imperfections which may impair durability or serviceability. 3. RE
13、GULATORY REQUIREMENTS. 3.1 The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided shall meet
14、the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and the quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such confor
15、mance. 5. PACKAGING. 5.1 Preservation, packing and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Unless otherwise specified, all dimensions are in inches. 6.2 Unless otherwise specified in the contract or purchase order, packaging shall be in accordance with ASTM D3951. Provi
16、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55592B 3 6.3 Pin without butt leaves will be supplied when the part identification number specifies dash 17. 6.4 The following part or identification numbering procedure is for government purposes and do
17、es not constitute a requirement for the contractors. The part number identification number (PIN) shall consist of the basic commercial item description number followed by a dash number from Table I, and material code. When protective finish is required for material A or D, add “F” to the PIN. Exampl
18、e: AA55592 -9 B Material code Dash number Basic number 6.5 Source of documents. 6.5.1 Department of Defense Specifications. Copies of Department of Defense specifications may be obtained from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094 or onl
19、ine at https:/assist.daps.dla.mil/quicksearch/. 6.5.2 FAR. The FAR may be obtained from the Regulatory Secretariat, 1800 F Street NW, Washington DC 20405 or online at http:/www.acqnet.gov. 6.5.3 ASTM Standards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Dri
20、ve, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org. 6.5.4 SAE Specifications. Copies of SAE specifications may be obtained from the Society of Automotive Engineers, Inc., 400 commonwealth Drive, Warrendale, PA 15096-0001 or online at http:/www.sae.org. 6.6 Ordering data. The contra
21、ct or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 6.7 Key words. Cadmium Knuckle Pitch 6.8 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate wh
22、ere changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only, and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of thi
23、s document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55592B 4 MILITARY ACTIVITIES: CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS C
24、ustodian: Army AR Preparing activty: Navy AS DLA IS Air Force 99 Review activities: (Project 5340-2010-024) Army MI Navy MC Air Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
