1、AMSC N/A FSC 9320 A-A-55759A 5 May 2011 SUPERSEDING A-A-55759 12 September 1995 COMMERCIAL ITEM DESCRIPTION RUBBER, SILICONE; SHEET, SOLID, SHAPE 15 The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This commercial item
2、 description (CID) covers a silicone rubber strip, shape 15 (see figure 1). 2. CLASSIFICATION. The silicone rubber will be of the following classes and grades as specified. The designated grade number corresponds to the nominal Shore Durometer A hardness value. Class 1A Low temperature resistant Gra
3、de 40, 50, 60, 70, and 80 Class 1B Low temperature resistant and low compression set at high temperature Grade 40, 50, 60, 70, and 80 Class 2A High temperature resistant Grade 25, 40, 50, 60, 70, and 80 Class 2B High temperature resistant and low compression set Grade 25, 40, 50, 60, 70, and 80 Clas
4、s 3A Low temperature, tear and flex resistant Grade 30, 50, and 60 Class 3B Tear and flex resistant Grade 30, 50, 60, 70, and 80 INCH-POUND Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia (DSCP), ATTN: DSCP-NASA, 700 Robbins Avenue, Phil
5、adelphia, PA 19111-5096 or e-mail to dscpg&inspecommentsdla.mil . Since contact information can change, you may want to verify the currency of this address information using ASSIST Online database at https:/assist.daps.dla.mil .Provided by IHSNot for ResaleNo reproduction or networking permitted wit
6、hout license from IHS-,-,-A-A-55759A 2 3. SALIENT CHARACTERISTICS. 3.1 Dimensional and physical requirements. Dimensional and physical requirements shall conform to figure 1. Dimensional tolerance shall conform to the applicable commercial tolerance specified in CID A-A-59588. ABCFigure 1. Dimension
7、al and physical requirements. Table I. Dash sizes and dimensions. DASH SIZE A THICKNESS B WIDTH C LENGTH TEMP RATING IN F NHR MIN TENSILE STRENGTH P.S.I COLOR 001-D-5 0.015 36.000 36.000 -80 to 425 45.0 to 55.0 700 Natural 002-D-6 0.016 36.000 36.000 -80 to 425 55.0 to 65.0 650 Gray 003-A-4 0.020 36
8、.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 004-F-5 0.020 36.000 36.000 -94 to 400 45.0 to 55.0 1200 Natural 005-D-5 0.031 12.000 12.000 -80 to 425 45.0 to 55.0 700 Natural 006-A-7 0.031 24.000 36.000 -100 to 425 65.0 to 75.0 600 Gray 007-F-3 0.031 24.000 60.000 -94 to 400 25.0 to 35.0 1000 Nat
9、ural 008-A-4 0.031 36.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 009-B-4 0.031 36.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 010-C-4 0.031 36.000 36.000 -80 to 425 35.0 to 45.0 700 Natural 011-C-7 0.031 36.000 36.000 -80 to 425 65.0 to 75.0 650 Natural 012-D-2 0.031 36.000 36.000 -80 to 42
10、5 15.0 to 30.0 700 Natural 013-D-4 0.031 36.000 36.000 -80 to 425 35.0 to 45.0 700 Natural 014-D-6 0.031 36.000 36.000 -80 to 425 55.0 to 65.0 650 Natural 015-D-7 0.031 36.000 36.000 -80 to 425 65.0 to 75.0 650 Natural 016-E-3 0.031 36.000 36.000 -130 to 400 20.0 to 35.0 850 Natural 017-E-5 0.031 36
11、.000 36.000 -130 to 400 45.0 to 55.0 1200 Gray 018-E-6 0.031 36.000 36.000 -130 to 400 55.0 to 65.0 1100 Natural 019-F-5 0.031 36.000 36.000 -94 to 400 45.0 to 55.0 1200 Natural 020-A-5 0.040 36.000 36.000 -100 to 400 45.0 to 55.0 700 Natural 021-D-6 0.062 10.000 10.000 -80 to 425 55.0 to 65.0 650 N
12、atural 022-D-5 0.062 12.000 120.000 -80 to 425 45.0 to 55.0 700 Natural 023-B-4 0.062 24.000 24.000 -100 to 425 35.0 to 45.0 700 Natural 024-B-4 0.062 24.000 24.000 -100 to 400 35.0 to 45.0 700 Natural 025-C-4 0.062 24.000 24.000 -80 to 425 35.0 to 45.0 700 Natural 026-C-5 0.062 24.000 24.000 -80 to
13、 425 45.0 to 55.0 700 Natural 027-C-6 0.062 24.000 24.000 -80 to 425 55.0 to 65.0 650 Black Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55759A 3 Table I. Dash sizes and dimensions Continued. DASH SIZE A THICKNESS B WIDTH C LENGTH TEMP RATING
14、IN F NHR MIN TENSILE STRENGTH P.S.I COLOR 028-D-5 0.062 24.000 24.000 -80 to 425 45.0 to 55.0 700 Natural 029-E-5 0.062 24.000 24.000 -130 to 400 45.0 to 55.0 1200 Natural 030-F-5 0.062 24.000 48.000 -94 to 400 45.0 to 55.0 1200 Gray 031-A-4 0.062 36.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 0
15、32-C-4 0.062 36.000 36.000 -80 to 400 35.0 to 45.0 700 Natural 033-C-5 0.062 36.000 36.000 -80 to 425 45.0 to 55.0 700 Natural 034-C-8 0.062 36.000 36.000 -80 to 425 75.0 to 85.0 650 Natural 035-D-2 0.062 36.000 36.000 -80 to 425 15.0 to 30.0 700 Natural 036-D-4 0.062 36.000 36.000 -80 to 425 35.0 t
16、o 45.0 700 Olive drab 037-D-5 0.062 36.000 36.000 -80 to 425 45.0 to 55.0 700 Natural 038-D-6 0.062 36.000 36.000 -80 to 425 55.0 to 65.0 650 Natural 039-F-3 0.062 36.000 36.000 -94 to 400 25.0 to 35.0 1000 Natural 040-F-5 0.062 36.000 36.000 -94 to 400 45.0 to 55.0 1200 Natural 041-F-6 0.062 36.000
17、 36.000 -94 to 400 45.0 to 55.0 1200 White 042-C-5 0.062 36.000 36.000 -80 to 425 45.0 to 55.0 700 Gray 043-E-3 0.062 36.000 36.000 -130 to 400 20.0 to 35.0 850 Natural 044-E-5 0.062 36.000 A/A -130 to 400 45.0 to 55.0 1200 Natural 045-B-4 0.062 40.000 72.000 -100 to 425 35.0 to 45.0 700 Natural 046
18、-A-5 0.062 24.000 24.000 -100 to 425 45.0 to 55.0 700 Natural 047-B-4 0.080 36.000 36.000 -100 to 425 35.0 to 45.0 700 Black 048-C-5 0.093 36.000 36.000 -80 to 425 45.0 to 55.0 700 Natural 049-B-4 0.093 36.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 050-C-4 0.093 36.000 36.000 -80 to 425 35.0 to
19、 45.0 700 Natural 051-C-5 0.093 36.000 36.000 -80 to 425 45.0 to 55.0 700 Black 052-D-4 0.093 36.000 36.000 -80 to 425 35.0 to 45.0 700 Natural 053-D-5 0.093 36.000 36.000 -80 to 425 45.0 to 55.0 700 Natural 054-F-3 0.093 36.000 36.000 -94 to 400 25.0 to 35.0 1000 Natural 055-F-6 0.093 36.000 36.000
20、 -94 to 400 55.0 to 65.0 1200 Natural 056-F-6 0.093 36.000 A/A -130 to 425 20.0 to 35.0 1200 Natural 057-D-5 0.100 36.000 36.000 -80 to 425 45.0 to 55.0 700 White 058-D-7 0.125 12.000 12.000 -80 to 425 65.0 to 75.0 650 Natural 059-C-8 0.125 12.000 24.000 -80 to 400 75.0 to 85.0 650 Black 060-A-5 0.1
21、25 24.000 24.000 -100 to 325 45.0 to 55.0 700 Natural 061-A-4 0.125 24.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 062-A-6 0.125 36.000 36.000 -100 to 425 55.0 to 65.0 650 Natural 063-C-2 0.125 36.000 36.000 -80 to 425 15.0 to 30.0 700 Natural 064-C-5 0.125 36.000 36.000 -80 to 425 45.0 to 55.0
22、700 Natural 065-C-6 0.125 36.000 36.000 -80 to 425 55.0 to 65.0 650 Black 066-D-5 0.125 36.000 36.000 -80 to 425 45.0 to 55.0 700 White 067-F-3 0.125 36.000 36.000 -94 to 400 25.0 to 35.0 1000 Black 068-F-5 0.125 36.000 36.000 -94 to 400 55.0 to 65.0 1200 Natural 069-F-6 0.125 36.000 36.000 -94 to 4
23、00 55.0 to 65.0 1200 Natural 070-F-8 0.125 36.000 36.000 -94 to 400 75.0 to 85.0 800 Natural 071-E-3 0.125 36.000 A/A -130 to 425 20.0 to 35.0 850 Natural 072-C-8 0.125 48.000 48.000 -80 to 425 75.0 to 85.0 650 White 073-D-5 0.150 24.000 24.000 -80 to 425 45.0 to 55.0 700 White 074-D-4 0.180 36.000
24、36.000 -80 to 425 35.0 to 45.0 700 White Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55759A 4 Table I. Dash sizes and dimensions Continued. DASH SIZE A THICKNESS B WIDTH C LENGTH TEMP RATING IN F NHR MIN TENSILE STRENGTH P.S.I COLOR 075-C-6 0
25、.188 36.000 36.000 -80 to 425 55.0 to 65.0 650 Natural 076-A-4 0.250 A/A A/A -100 to 425 35.0 to 45.0 700 Natural 077-C-5 0.250 12.000 12.000 -80 to 425 45.0 to 55.0 700 Natural 078-A-6 0.250 36.000 36.000 -100 to 425 55.0 to 65.0 650 Natural 079-C-5 0.250 36.000 36.000 -80 to 425 45.0 to 55.0 700 N
26、atural 080-D-4 0.250 36.000 36.000 -80 to 425 35.0 to 45.0 700 Natural 081-D-6 0.250 36.000 36.000 -80 to 425 55.0 to 65.0 650 Olive drab 082-F-5 0.250 36.000 36.000 -94 to 400 45.0 to 55.0 1200 Natural 083-F-8 0.250 36.000 36.000 -94 to 400 75.0 to 85.0 800 Natural 084-C-6 0.250 36.000 36.000 -80 t
27、o 425 55.0 to 65.0 650 Natural 085-E-3 0.250 48.000 48.000 -130 to 400 20.0 to 35.0 850 Natural 086-E-5 0.281 36.000 36.000 -130 to 400 45.0 to 55.0 1200 Natural 087-C-5 0.320 12.000 12.000 -80 to 425 45.0 to 55.0 700 Natural 088-B-5 0.393 11.790 11.790 -100 to 425 45.0 to 55.0 700 Natural 089-F-5 0
28、.438 24.000 24.000 -94 to 400 45.0 to 55.0 1200 Gray 090-F-5 0.625 24.000 24.000 -94 to 400 45.0 to 55.0 1200 Natural 091-C-4 0.625 36.000 36.000 -80 to 425 35.0 to 45.0 700 White 092-F-5 0.750 24.000 48.000 -94 to 400 45.0 to 55.0 1200 Gray 093-F-6 1.000 24.000 24.000 -94 to 425 55.0 to 65.0 1200 N
29、atural 094-C-4 1.250 36.000 36.000 -80 to 425 35.0 to 45.0 700 Natural 095-F-3 0.080 36.000 A/A -94 to 400 25.0 to 35.0 1000 Gray 096-B-4 0.125 36.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 097-B-4 0.250 36.000 36.000 -100 to 425 35.0 to 45.0 700 Natural 098-D-5 0.050 36.000 36.000 -80 to 425 4
30、5.0 to 55.0 700 Natural 099-B-6 0.031 36.000 36.000 -100 to 425 55.0 to 65.0 650 Gray Notes: 1. Unless otherwise noted, dimensions are in inches. 2. Surface condition: Smooth. 3. Surface condition location: One side. 4. Color location: Both sides. 5. NHR: Nonmetallic hardness rating, Shore Durometer
31、 A. 6. Minimum tensile strength: psi 7. A/A: Any acceptance 3.2 Material. Material shall be silicone rubber formulated and processed to meet the physical and mechanical properties per the specified class and grade, when tested in accordance with ASTM test methods specified in Table I of CID A-A-5958
32、8. 3.3 Color. Unless otherwise specified, the color of the silicone rubber shall be the natural color of the compound furnished. 3.4 Workmanship. The end product shall be clean, smooth finished, and free from dirt, flash or rough edges. 3.5 Marking. Unless otherwise specified (see ordering data), sh
33、eet material and strips (cut from sheet) shall be marked with the following information: Basic CID number, class, grade, designations, and the suppliers designations. The class and grade designations separated by a Provided by IHSNot for ResaleNo reproduction or networking permitted without license
34、from IHS-,-,-A-A-55759A 5 dash, shall be enclosed within parentheses. The markings shall be legible and placed in rows of constantly 5 inches apart. The suppliers designation (compound number) shall appear immediately below the constantly recurring description symbols. The symbols shall be legible a
35、nd shall be not less than 3/8 inches high. The symbols shall be applied by suitable means, using a black colored marking fluid to mark white colored silicones and a white colored marking fluid to mark other than white colored silicones. The marking shall not be obliterated by normal handling or by t
36、he action of petroleum-based oils. 3.6 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of ASTM SI 1
37、0, and all other requirements of this commercial item description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. 4.
38、 REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE. 5.1 Product conformance. The products provided shall meet the salient
39、characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 6. PACKAG
40、ING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 Part identification number (PIN): the following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. The PINs to be used for i
41、tems acquired to this description are created as follows: Basic CID number + dash size from Table I. Do not use unassigned dash size. AA55759 001 D 5 Grade 2 =25Clas 330 A =1A 4 =4BB 550 C =2A 6 =6DB 770 E =3A 8 =8FB Dash size (without class & grade) from Table I Basic CID number Provided by IHSNot
42、for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55759A 6 7.2 Ordering data. The contract or order should specify the following: a. Title, number, and date of this CID. b. Dash size from Table I. c. Marking if different (see 3.5). d. Packaging requirements. 7.3 Sour
43、ce of documents. 7.3.1 ASTM SI10 is available from the ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org . 7.3.2 FAR. The Federal Acquisition Regulation is available from the Superintendent of Documents, U.S. Government Printing Office, Washi
44、ngton, DC 20402 or online at http:/www.arnet.gov/far . 7.3.3 Government documents. Federal and military documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. 7.4 Utiliza
45、tion caution. Use of this material in items that may come in contact with human skin, food, or portable water is not recommended without prior approval of the appropriate medical service. 7.5 Key words. Class Flex resistant Grade Low compression 7.6 Changes from previous issue. Marginal notations ar
46、e not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Military interests: Custodians: Preparing activty: Army MR DLA - IS Navy AS Air Force - 11 (Project 9320-2011-012) NOTE: The activities listed above were interested in this document a
47、s of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
