1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you m
2、ay want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 6810 METRIC A-A-59107A 24 March 2011 SUPERSEDING A-A-59107 9 September 1997 COMMERCIAL ITEM DESCRIPTION TOLUENE, TECHNICAL The General Services Administration has authorized the u
3、se of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers one technical grade of toluene. 2. SALIENT CHARACTERISTICS 2.1 Chemical and physical characteristics. Technical grade toluene shall conform to the chemical and physical characteri
4、stics of table I when tested as specified therein. TABLE I. Chemical and physical characteristics of technical grade toluene. Requirement Specification limit Test method Specific gravity 20 C/20 C (68 F/68 F) 0.860 - 0.870 ASTM D891 1Color platinum-cobalt scale No. 20 max ASTM D1209 Distillation ran
5、ge at 760 mm mercury (Hg) Not more than 2 C (3.6 F) from initial boiling point to dry point, including the temperature of 110.6 C (231 F) ASTM D850 2Residual odor None ASTM D1296 Water at 20 C (68 F) No evidence of turbidity or free water See 2.2 Acidity No evidence of acidity ASTM D847 Acid color w
6、ash Not darker than No. 4 color standard ASTM D848 Sulfur compounds Free of hydrogen sulfide and sulfur dioxide ASTM D853 Copper corrosion Pass ASTM D849 1Measured to the third decimal place. 2Using a thermometer with a minimum range of 98 to 152 C (208 to 306 F), with a maximum subdivision of 0.2 C
7、 or a device with equivalent measuring performance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59107A 2 2.2 Water. Place 10 milliliters (mL) of the sample in a dry, loosely stoppered test tube (16 by 150 millimeters (mm) and place in a water
8、 bath at 20 C (68 F). On viewing the test tube transversely at the end of 3 minutes, no turbidity should be observed and no free water should appear in the bottom of the tube. 3. REGULATORY REQUIREMENTS 3.1 Labeling, packaging, and marking. Item shall be labeled, packed, and marked in accordance wit
9、h 49 Code of Federal Regulations (CFR), Parts 100 to 199. 3.2 Material safety data sheet (MSDS). A MSDS shall be furnished in accordance with FED-STD-313, “Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities“, and 29 CFR 1910.1200, “
10、Hazard Communication“. 3.3 Hazard warning label. An Occupational Safety and Health Administration hazard warning label shall be furnished in accordance with 29 CFR 1910.1200. 3.4 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, i
11、n accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS 4.1 Product conformance. The product provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance
12、practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 4.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 5. PACKAGING 5
13、.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specified in the acquisition order (see 6.2(b). 6. NOTES 6.1 Sources of documents. 6.1.1 CFR and FAR. Copies of CFR and FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 1525
14、0-7954. Electronic copies of CFR documents may be obtained from http:/www.gpoaccess.gov/ecfr/. Electronic copies of FAR documents may be obtained from https:/www.acquisition.gov/far/.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59107A 3 6.1.2
15、Federal standards. Copies of federal standards may be obtained from General Services Administration, Federal Supply Service, Specification Section, 470 East LEnfant Plaza SW, Suite 8100, Washington, DC 20407. Electronic copies may be obtained from https:/assist.daps.dla.mil/. 6.1.3 ASTM standards. C
16、opies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies may be obtained from http:/www.astm.org/. 6.2 Ordering data. The acquisition order should specify the following information: a. CID document numb
17、er and revision. b. Preservation, packing, and marking (see 5.1). 6.3 Subject term (key word) listing. Solvent Thinner MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians: GSA - FAS Army - AR Navy - SH Air Force - 68 DLA - GS Other - DS Review Activities: Army - MD1, MI Navy - MC, OS P
18、reparing Activity: DLA - GS3 (Project 6810-2011-003) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
