1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datawhich may improve this document should be sent to: Commanding Officer (Code 15E2), NavalConstruction Battalion Center, 1000 23 rd Avenue, Port Hueneme, CA 93043-4301, by using theStandardization Document Imp
2、rovement Proposal (DD Form 1426) appearing at the end of thisdocument or by letter.AMSC N/A FSC 4940INCH-POUNDA-A-59211May 18, 1998SUPERSEDINGRR-P-125BSeptember 16, 1975COMMERCIAL ITEM DESCRIPTIONPARTS CLEANING CAN, SAFETY, BENCHThe General Services Administration has authorized the use of this comm
3、ercial itemdescription for all Federal agencies.1. SCOPE. This commercial item description (CID) covers bench-type safety cans for containingflammable or solvent liquids used in the cleaning or swabbing of small parts.2. CLASSIFICATION. The bench-type safety cans shall be of the following sizes, as
4、specified(see 7.2):Size:1-quart (0.95 litre (L)2-quart (1.89 L)2-gallon (7.57 L)3-gallon (11.36 L)3. SALIENT CHARACTERISTICS.3.1 Description . The bench-type safety cans shall have a cylindrical body with a removableretainer ring, a hinged cover, and a perforated metal dasher (fire baffle), which is
5、 mounted on acoil spring. The 2-quart (1.89 L), 2-gallon (7.57 L), and 3-gallon (11.36 L) sized bench-typesafety cans shall have two handles welded to the body and a support stand welded to the cover.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-
6、A-592112The carrying handles shall be located directly opposite each other and 90 degrees from the coverhinge. The cover support stand shall position the cover horizontal within 5 degrees of the topof the body. The carrying handles and cover stand are not required on 1-quart (0.95 L) sizebench-type
7、safety cans. The bench-type safety cans shall be free of leakage. The dasher shall nottouch the surface of the liquid when the can is filled to capacity.3.2 Standard commercial product . The bench-type safety cans shall, as a minimum, be inaccordance with the requirements of this commercial item des
8、cription and shall be themanufacturers standard commercial product. Additional or better features which are notspecifically prohibited by this commercial item description but which are a part of themanufacturers standard commercial product, shall be included in the bench-type safety cans beingfurnis
9、hed. A standard commercial product is a product which has been sold or is being currentlyoffered for sale on the commercial market through advertisements or manufacturers catalogs, orbrochures, and represents the latest production model.3.3 Dimensions . The dimensions of the bench-type safety cans s
10、hall be as shown in table I for thesize specified (see 7.2). The nominal plate thickness shall be 0.0179-inch (0.45 millimetre (mm)for the 1- and 2-quart (0.95 and 1.89 L) sizes and 0.0239-inch (0.61 mm) for the 2- and 3-gallon(7.51 and 11.36 L) sizes. The height and diameter of the bench-type safet
11、y cans may varybetween the limiting dimensions shown.TABLE I. Bench-type safety can dimensions .Size(minimumcapacity)Height 1 /(inches (mm)Diameter(inches (mm)Coil spring wirediameter(nominal)2 / - 3 /(inches (mm)1-quart(0.95 L)3.25 - 4.25(82.55 - 107.95 mm)5.50 - 6.50(139.70 - 165.10 mm)0.092(2.34
12、mm)2-quart(1.89 L)3.75 - 5.75(95.25 - 146.05 mm)7.25 - 8.50(184.15 - 215.90 mm)0.106(2.69 mm)2-gallon(7.57 L)6.75 - 7.75(171.45 - 196.85 mm)11.25 - 13.25(285.75 - 336.55 mm)0.162(4.11 mm)3-gallon(11.36 L)6.75 - 7.50(171.45 - 190.50 mm)13.44 - 15.50(341.38 - 393.70 mm)0.192(4.88 mm)1 / The height of
13、the can is defined as the distance from the bottom edge to the top of crownpor tion of the cover.2 / A 25 percent larger diameter wire is acceptable.3 / Commercial tolerances apply.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5921133.4 Compone
14、nts .3.4.1 Body and bottom. The body and bottom shall be attached to each other in accordance withmanufacturers standard practice. The bottom edge shall be rolled over to eliminate sharp edges.Not less than two clips, opposite each other, shall be welded to the body for engagement with theretainer r
15、ing. The clips shall be so positioned for proper retention and release of the retainer ring.The clips shall be fabricated from plate having a thickness not less than that specified for the body.3.4.2 Retainer ring. The retainer ring, when assembled to the body, shall be designed to maintainequal and
16、 positive pressure on the dasher and coil spring assembly. The ring shall have adiscontinued, rolled, outer lip and the ring shall be notched to fit inside the body. The ring shallbe retained on the body by the body clips engaging the rolled outer lips of the ring. The ring shallbe removable by rota
17、ting, thereby disengaging the lips of the retainer ring from the body clips.3.4.3 Cover. The cover shall be attached to the body by a metal hinge. The hinge shall belocated astride or beside any body seam. The cover shall have a handle welded to it. When thecan has a cover support stand that may be
18、used as a handle, a separate handle is not required.3.4.4 Dasher. The dasher shall be perforated over the entire surface. The dasher shall have aflanged rim of sufficient depth to enclose the coil spring, and shall be concaved at the center toprovide a recessed area.3.4.5 Coil spring. The coil sprin
19、g shall be formed of one piece of wire. The spring shall be coiledto an outside diameter which will provide engagement within the dasher.3.4.6 Handles and cover support stand. The cover handle, the two carrying handles, and thecover support stand shall each be made of one piece of plate having a thi
20、ckness not less than thatspecified for the body. The carrying handles and the retaining clips (see 3.4.1) may be fabricatedas a carrying handle with two retaining clips.3.5 Treatment and painting . Unless otherwise specified (see 7.2), the cleaning bench-type safetycans shall be treated and painted
21、in accordance with the manufacturers standard practice. Allsurfaces of the cleaning bench-type safety cans, other than corrosion-resistant steel, shall beprotected against corrosion and present a neat appearance.3.6 Marking . Each can shall be permanently marked on the body or cover using not less t
22、han0.25-inch (6.35 mm) characters, showing “US,” size, and manufacturers code identificationnumber, name, or trademark.4. REGULATORY REQUIREMENTS.4.1 Materials . The offeror/contractor is encouraged to use recovered materials to the maximumextent practicable, in accordance with paragraph 23.403 of t
23、he Federal Acquisition Regulation(FAR). Unless otherwise specified herein, all equipment, material, and articles incorporated in thework covered by this commercial item description are to be new and fabricated using materialsProvided by IHSNot for ResaleNo reproduction or networking permitted withou
24、t license from IHS-,-,-A-A-592114produced from recovered materials to the maximum extent possible without jeopardizing theintended use. The term “recovered materials” means materials which have been collected orrecovered from solid waste and reprocessed to become a source of raw materials, as oppose
25、d tovirgin raw materials. Unless otherwise specified, none of the above shall be interpreted to meanthat the use of used or rebuilt products are allowed under this commercial item description.4.2 Metric products . Products manufactured to metric dimensions will be considered on anequal basis with th
26、ose manufactured using inch-pound units, provided they fall within specifiedtolerances using conversion tables contained in the latest version of ASTM SI-10(IEEE/ASTM SI-10), and all other requirements of this commercial item description includingform, fit and function are met. If a product is manuf
27、actured to metric dimensions and thesedimensions exceed the tolerances specified in the inch-pound units, a request should be made tothe contracting officer to determine if the product is acceptable. The contracting officer has theoption of accepting or rejecting the product.5. QUALITY ASSURANCE PRO
28、VISIONS.5.1 Product conformance . The products provided shall meet the salient characteristics of thiscommercial item description, conform to the producers own drawings, specifications, standards,and quality assurance practices, and be the same product offered for sale in the commercialmarket. The g
29、overnment reserves the right to require proof of such conformance.6. PACKAGING. The preservation, packing, and marking shall be as specified in the contract ororder.7. NOTES.7.1 Source of documents .7.1.1 The Federal Acquisition Regulation (FAR) is available from the Superintendent ofDocuments, U.S.
30、 Government Printing Office, Washington, DC 20402.7.1.2 ASTM Standard is available from the Society for Testing and Materials, 100 Barr HarborDrive, West Conshohocken, PA 19428-2959.7.1.3 IEEE Standard is available from the Institute of Electrical and Electronics Engineers(IEEE), IEEE Service Center
31、, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855-1331.7.2 Ordering data . Acquisition documents should specify the following:a. Title, number, and date of this CID.b. Size of cleaning can required (see 2).c. When bench-type safety cans are other than as specified (see 3.3).d. When treatment and
32、painting is other than as specified (see 3.5).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5921157.3 National Stock Number (NSNs) . The following is a list of NSNs assigned which correspondto this CID. The list may not be indicative of all pos
33、sible NSNs associated with the CID.NSN 4940-00-278-0617NSN 4940-00-278-0619NSN 4940-00-286-2668NSN 4940-00-684-05807.4 Supersession data . This CID replaces Federal Specification RR-P-125B datedSeptember 16, 1975.7.5 Part Identification Number (PIN) . The following part identification numbering proc
34、edure isfor government purposes and does not constitute a requirement for the contractor. The PINs tobe used for items acquired to this description are created as follows:AA59211 - CDocument identifierSizeThe above PIN is for size 2-gallon (7.57 L) (see table II).TABLE II. PIN designators .Size PIN
35、designator1-quart2-quart2-gallon3-gallonABCD7.6 Metric units . The values stated in either inch-pound units or SI units are to be regardedseparately as standard. Within the text, the SI units are shown in brackets. The values stated ineach system are not exact equivalents; therefore, each system sho
36、uld be used independently of theother. Combining values from the two systems may result in non-conformance with the standard.7.7 Subject term (key word) listing .Bench-typeCleaningSafety can7.8 Changes from previous issue . Marginal notations are not used in this revision to identifychanges with res
37、pect to previous issue due to the extensiveness of the changes.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-592116MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians : G SA - FSSArmy - ALNavy - YD1 Preparing Activity :Air Force -
38、 99 Navy - YD1Review Activities : (Project 4940-0736)Navy - AS, CG, NPAir Force - 03, 11, 82DLA - CCProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete block
39、s 1, 2, 3, and 8. In block 1, both the document number and revision letter should begiven.2. The submitter of this form must complete blocks 4, 5, 6, and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of docu
40、ments, nor to request waivers, or clarification of requirements on currentcontracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenceddocument(s) or to amend contractual requirements.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-59211 2. DO
41、CUMENT DATE (YYMMDD)9805183. DOCUMENT TITLEPARTS CLEANING CAN, SAFETY, BENCH4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.)5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS
42、 (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) AUTOVON(if applicable)7.DATE SUBMITTED(YYMMDD)8. PREPARING ACTIVITYa. NAMEROBERT J. BRICKEYb. TELEPHONE Include Area Code)(1) Commercial (2) AUTOVON805-982-5593 551-5593c. ADDRESS (Include Zip Code)COMMANDING OFFICER, NCBC CODE 15
43、E2B1000 23RD AVENUEPORT HUENEME, CA 93043-4301IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:DEFENSE QUALITY AND STANDARDIZATION OFFICE5203 Leesburg Pike, Suite 1403, Falls Church, VA 22401-3466Telephone (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
