1、 A-A-59349 = 9038054 0003680 OTB FJCH-POUND J A-A-5 93 49 9 October 1998 SUPERSEDING 21 November 1990 MIL-R-779E COMMERCIAL ITEM DESCRIPTION REFLECTORS, LIGHT; WITH HOLDER The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOP
2、E. This commercial item description (CID) covers light reflectors with holders for indoor or outdoor installations. The light reflectors covered by this CID are intended for use in shielding and enhancing the illumination of incandescent drop lights, side lights, wail lights, and platform lights. 2.
3、 CLASSIFICATION. The light flectors shall be of the following types and sizes. Type is determined by the reflector shape. Size-is determined by the width of the reflector opening at its widest point (gendy the dimeter). The type and size to be fimished shall be as specified (see 72(b). Type I - Cone
4、 Type II - Dome Type III - Angle Type IV - Parabola Size 1 - 6 inches Size 2 - 8 inches Size 3 - 10 inches Size 4 - 12 inches Size 5 - 14 inches Size 6 - 16 inches Size 7 - 18 inches Size 8 - 20 inches Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data whi
5、ch may improve this document should be sent to: Defense Supply Center Richmond, A“: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610. AMSC NfA FSC 6210 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling Services A-A-59349
6、 9018054 0003681 T34 A-A-59349 3. SALIENT CHARACTERISTICS 3.1 General requirements. The light reflector shall be capable of attachment to an indoor or outdoor light fixture. The reflector shall cover and direct the light beam of the fixhue. Unless otherwise specified (see 7.2(c), the reflector shall
7、 be capable of accommodating and withstanding the heat fiom a 100-watt lamp. When specified (see 7.2(d), the reflector shall be tapped for mounting on OS-inch conduit. Dissimilar metals shall be insulated fiom each other. 3.2 Components. The light reflector shall include, as a minimum, the following
8、 components: 3.2.1 Reflector body. Unless otherwise specified (see 7.2(e), the reflector body shall be made of aluminum. The reflector shall be free of sharp edges. The metal shail be of uniform thickness and of sufficient thickness to produce a rigid construction. Unless otherwise specified (see 7.
9、2(f), the open end of the reflector shall be circular. For type I light reflectors, the angle between the reflector surface and the centerline of the cone shall be 45 or 80 degrees as specified (see 7.2Cg). Unless otherwise specified (see 7.2(h), the outside of the reflector body shall be green. Unl
10、ess otherwise specified (see 7.2(i), the outside surface of the reflector body shall be covered by fused porcelain enamel. When specified (see 7.20), the reflector body shall be vented. 3.2.2 Reflector holder. The light reflector shall be furnished with a holder of a clamp type, a pendant hood, or a
11、n equally adequate means of securing the reflector to the light fixture as specified (see 7.20). If a pendant hood is furnished, it shall contain a mogul- or medium-based lamp receptacle as specified (see 7.2(1). 3.2.3 LamDholder. If required (see 7.2(m), the light reflector shall include a rigid or
12、 shock- absorbing lampholder. The lampholder shall conform to Underwriters Laboratory (UL) 496. 3.2.4 Power cord. If required (see 7.2(n), the light reflector shall iriclude a 6-f00t, 3-conductor, SJ-type electrical cord meeting the requirements of UL 62. 3.2.5 ptional comuonents. Optional component
13、s shall be furnished as specified (see 7.2(0). 3.3 Performance. The inner (reflecting) surface of the reflector shall have a reflection factor of not less than 70 percent, measured in accordance with Society of Automotive Engineers (SAE) J964. Unless otherwise specified (see 7.2(p), the reflector sh
14、all be capable of rotating around the lamp receptacle to which it is secured. 4. REGULATORY REQUIREMENT 4.1 Recovered materials. The offerodcontractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation
15、 (FAR). 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The light reflector shall meet the salient characteristics of this commercial item description; conform to the manuficimers own drawings, specifications, 2 Licensed by Information Handling Services. A-A-59349 9018054 0003b82 970 A-A-59
16、349 standards, and quality assurance practices; and be the same light reflector offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.1.1 Verification of conformance. Suitable verication of conformance to SAE-J964, UL-62, and UL-496 shal
17、l be by either the SAE or UL label or certification of such conformance by an accredited testing laboratory satisfactory to the Government. 5.2 Warranty. Unless otherwise specified (see 7.2(q), the manufacturers standard Commercial warranty, terms, and conditions shall apply. 6. PACKAGING. Preservat
18、ion, packing, and marking shall be as specified (see 7.2(r) in the contract or purchase order. 7. NOTES 7.1 Referenced documents. 7.1.1 Government documents. Copies of Federal documents may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. 7.1.2
19、 Industw standards. Copies of industry standards referenced in this CID may be obtained fiom the following addresses: - Society of Automotive Engineers (SAE) SAE-J964 Test Procedure for Determining Reflectivity of Rear View Mirrors Applications for copies should be sent to: Society of Automotive Eng
20、ineers, Inc., 400 Commonwealth Drive, Warrendale, PA 15096. Underwriters Laboratories Inc. (UL) ANSIKJL-496 Edison-Base Lampholders ANSUUL-62 Flexible Cord and Fixture Applications for copies should be sent to: Underwriters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062. 7.2 Orderinn da
21、ta. Acquisition documents must specie the following: a. Title, number, and date of this document. b. Type and size of light reflector required (see 2). c. Lamp wattage capacity, if different (see 3.1). d. Tapped for OS-inch conduit mounting, if required (see 3.1). e. Composition of reflector body, i
22、f different (see 3.2.1). 3 Licensed by Information Handling ServicesA-A-5 9349 A-A-59349 9018054 0003683 807 f. Shape of reflector opening, if different (see 3.2.1). g. Angle between reflector surface and centerline, speciQ if type I (see 3.2.1). h. Color of outside surface of reflector body, if dif
23、ferent (see 3.2.1). i. Type of paint/enamel, if different (see 3.2.1). j. Vented reflector body, if required (see 3.2.1). k. Type of reflector holder required (see 3.2.2). 1. Type of lamp receptacle, if required (see 3.2.2). m. Type of lampholder, as specified (see 3.2.3). n. Power cord, as specifie
24、d (see 3.2.4). o. Optional components, as specified (see 3.2.5). p. Performance, if different (see 3.3). q. Warranty, if different (see 5.2). r. Packaging requirements, as specified (see 6). 7.3 Part identification number (PIN). The following part identification numbering procedure is for government
25、 purposes and does not constitute a requirement for the contractor. A-A-59349 -X X L Size: 1 -6inches 2 - 8 inches 3 - 10inches 4 - 12 inches 5 - 14 inches 6 - 16 inches 7 - 18 inches 8 -2Oinches I Type: A - Type I (Cone) B - Type II (Dome) C - Type III (Angle) D - Type IV (Parabola) CID number MILITARY INTERESTS: PREPARING ACTIVITY DLA - GS Custodian Navy - MC (Project 6210-1065) 4 Licensed by Information Handling Services
