1、IINCH-POUND( Type I II III IV A-A-5 9560 23 June 2000 SUPERSEDING 16 July 1991 MIL-P-5514911D Color A B C D E Red .690 .980 .468 8-32 .343 Black .690 .980 .468 8-32 .343 Red 370 min 1 .O5 .640 10-32 .468 Black .910 ma. 1 .O5 .640 10-32 .468 COMMERCIAL ITEM DESCRIPTION POST, BINDING, ELECTRICAL (INSU
2、LATED) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) establishes the government acquisition requirements for an insulated electrical binding post to be used as a wiring termina
3、tion and banana plug receptacle on terminal boards and test set panels. 2. CLASSIFICATION. The electrical binding post shall be classified and identified by the types in accordance with the characteristics specified in table I. The selected type of product to be supplied shall be specified in the ac
4、quisition order (see 7.4(b). TABLE I. Binding post dimensions. See figure i. 3. SALIENT CHARACTERISTICS 3.1 Components. The product shall be similar to the one shown in figure 1. The product shall consist of the binding post, insulated captive head and washers, and all mounting hardware. Beneficial
5、comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610. AMSC NIA FSC 5940 DISTRIBUTION STATEMENT A. Approved for
6、public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59560 HEX NUT NO. 8-32 UNC-2B .125 x .344 ACROSS FLATS (M55149/01-FA-01 8, -02) EX NUT NO. 10-32 UNF-2B .125 x .375 ACROSS FLATS (M55149/01-FA-03 8, -04) F
7、LAT WASHER INTERNAL -TOOTH LOCKWASH SEENOTE 2 SECTION E-E X .350 MIN DEPTH BANANA PLUG RECEPTACLE FIGURE 1. Binding post conmation. Notes: 1. The figure depicts only general characteristics and is not intended to limit specific manufacturing processes. 2. This is the insulated portion. 3. Dimension
8、(listed in table I) are in inches. Tolerance isN.015 inch unless otherwise shown. 3.2 Materials. 3.2.1 Metal. Unless specified otherwise in the acquisition order (see 7.4(c), the current-carrying portions of the binding post shall be brass conforming to the requirements of the American Society for T
9、esting and Materials (ASTM) B 16, “Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines“ (DoD adopted). 3.2.2 Finish. Unless specified otherwise in the acquisition order (see 7.4(d), metal portions of the binding post shall be gold plated in accordance with AST
10、M B 488, “Standard Specification for Electrodeposited Coatings of Gold for Engineering Uses“ (DoD adopted). 3.2.2.1 Unless otherwise specified in the acquisition order (see 7.4(e), the solder terminal end shall be tin plated in accordance with ASTM B 545, “Standard Specification for Electrodeposited
11、 Coatings of Tin“ (DoD adopted). 3.2.3 Insulation. The material used for the insulated portions of the binding post shall be specified in the acquisition order (see 7.4(f). The insulated parts of an individual binding post shall all be of the same color and, unless otherwise specified in the acquisi
12、tion order (see 7.4(g), shall be the color listed in table I. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59560 3.3 Non-turn feature. Unless specified otherwise in the acquisition order (see 7.4(h), the non-turn feature shall be a flatted b
13、oss as shown in figure 1. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offerorkontractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Produ
14、ct conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government
15、reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. For acquisition purposes, the products shall be preserved,
16、packed, and marked as specified in the acquisition order (see 7.4(i). 7. NOTES 7.1 Part or identification number (PIN). The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. Dash number (1 = Type I (see table I)
17、(2 = Type II (see table I) (3 = Type III (see table I) (4 = Type IV (see table I) I CIDnumber 7.2 Sources of documents. 7.2.1 m. The FAR may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001. 3 Provided by IHSNot for ResaleNo reproduction or
18、 networking permitted without license from IHS-,-,-A-A-59560 Type I 7.2 2 ASTM standards. Copies of ASTM standards may be obtained from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Assigned NSN 5940-00-842-6483 7.3 National stock number (NS
19、N). The NSNs listed in table II are assigned for the listed product types (see table I). Other NSNs may also correspond with this document. III IV TABLE II. Binding post NSNs 5 940-00-269-2220 5940-00-269-22 19 PIN number in A-A-59560 I II I 5940-00-044-1583 I Part number in MIL-P-55149AD AA59560 -
20、4 7.4 Ordering data. Acquisition documents must spec the following information: M55149/01-FA-04 a. CID document number, revision, and CID PIN b. Product classification (type) (see table I) c. Current-carrying material, if different (see 3.2.1) d. Binding post finish, if different (see 3.2.2) e. Sold
21、er terminal end finish, if different (see 3.2.2.1) f. Insulation material (see 3.2.3) g. Insulation material color, if different (see 3.2.3) k Non-turn feature, if different (see 3.3) i Packaging requirements (see 6.1) 7.5 Substitution data. See table III. I AA59560 - 1 I M55149/01-FA-01 I I AA59560
22、 - 2 I M55149/01-FA-02 I I AA59560 - 3 I M55 149/01 -FA-O3 I 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59560 MILITARY INTERESTS: Custodians: Navy - EC Air Force - 11 Amiy - CR Reviewers: Air Force - 99 Amiy - MI CIVIL, AGENCY COORDINATING ACTIVITY: GSA - 7FXE Preparing activity: DLA - GS (Project 5940-1394) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
