1、INCH-POUND A-A-59561A 24 August 2011 SUPERSEDING A-A-59561 23 June 2000 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highw
2、ay, Richmond, VA 23297-5616. Since contact information can change, you may want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 5365 COMMERCIAL ITEM DESCRIPTION SHIM, SOLID, ROUND The General Services Administration has authorized the
3、use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) establishes the government acquisition requirements for shims to be used for maintaining a predetermined distance between two surfaces. 2. CLASSIFICATION. The shims shall be similar to
4、that shown in figure 1 and classified by the types listed below and by the sizes listed in table I. The type and size shall be specified in the acquisition order (see 7.4(b). Type I - Aluminum alloy, anodized Type II - Aluminum alloy, chemically treated Type III - Brass, black chemical finish Type I
5、V - Corrosion resistant steel (CRES), passivated Type V - Carbon steel, cadmium plated FIGURE 1. Shim, solid, round. S T R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59561A 2 TABLE I. Size codes and dimensions. Thickness (T) T = .001 T = .00
6、5 T = .010 T = .013 Size R S Size R S Size R S Size R S 0001 0.088 0.153 0050 0.100 0.188 0087 0.093 0.187 0140 0.128 0.315 0002 0.125 0.187 0051 0.127 0.218 0088 0.094 0.205 0141 0.199 0.305 0003 0.187 0.500 0052 0.128 0.281 0089 0.128 0.315 0142 0.320 0.425 0004 0.190 0.246 0053 0.130 0.188 0090 0
7、.156 0.250 0143 0.502 0.750 0005 0.252 0.344 0054 0.190 0.344 0091 0.198 0.450 T = .014 0006 0.447 0.625 0055 0.252 0.344 0092 0.199 0.305 Size R S T = .002 0056 0.255 0.390 0093 0.234 0.500 0144 0.128 0.315 Size R S 0057 0.317 0.470 0094 0.252 0.308 0145 0.198 0.450 0007 0.128 0.250 0058 0.377 0.49
8、8 0095 0.252 0.344 0146 0.210 0.510 0008 0.130 0.188 0059 0.393 0.627 0096 0.255 0.350 0147 0.324 0.520 0009 0.200 0.400 0060 0.415 0.470 0097 0.260 0.300 0148 0.630 0.781 0010 0.250 0.359 0061 0.503 0.625 0098 0.260 0.335 0149 1.110 1.250 0011 0.250 0.748 0062 0.600 0.740 0099 0.258 0.368 T = .015
9、0012 0.275 0.360 0063 0.625 0.734 0100 0.281 0.500 Size R S 0013 0.275 0.750 0064 0.752 1.000 0101 0.284 0.544 0150 0.128 0.315 0014 0.393 0.627 0065 0.753 0.975 0102 0.312 0.415 0151 0.187 0.250 0015 0.395 0.930 0066 1.000 1.250 0103 0.320 0.425 0152 0.235 0.290 0016 0.399 0.555 0067 1.432 1.623 01
10、04 0.324 0.520 0153 0.265 0.500 0017 0.500 0.700 0068 1.650 1.840 0105 0.377 0.498 0154 0.380 0.625 0018 0.753 0.975 0069 2.190 2.438 0106 0.378 0.810 0155 0.520 0.660 0019 0.795 0.867 0070 3.050 3.313 0107 0.380 0.585 0156 0.750 0.990 0020 0.900 0.995 T = .006 0108 0.393 0.627 0157 0.752 1.000 0021
11、 1.000 1.375 Size R S 0109 0.531 1.000 0158 1.031 1.281 0022 1.432 1.623 0071 0.200 0.510 0110 0.753 0.975 T = .016 0023 2.190 2.438 0072 0.280 0.500 0111 0.840 1.310 Size R S 0024 2.435 2.873 0073 0.280 0.760 0112 1.078 1.375 0159 0.094 0.160 0025 3.050 3.313 0074 0.320 0.700 0113 1.320 2.000 0160
12、0.109 0.245 T = .003 0075 0.681 1.000 0114 2.182 2.750 0161 0.128 0.375 Size R S 0076 0.800 0.980 0115 2.190 2.438 0162 0.140 0.312 0026 0.096 0.140 0077 0.812 2.000 0116 2.435 2.873 0163 0.150 0.300 0027 0.125 0.250 0078 1.020 1.325 0117 2.515 3.225 0164 0.156 1.375 0028 0.166 0.250 0079 1.080 1.49
13、0 0118 2.598 3.313 0165 0.160 0.205 0029 0.190 0.265 0080 1.320 2.050 0119 3.050 3.313 0166 0.166 0.250 0030 0.250 0.359 0081 3.515 4.015 0120 6.000 6.250 0167 0.175 0.245 0031 0.252 0.344 T = .007 0121 10.930 12.312 0168 0.200 0.313 0032 0.313 1.000 Size R S T = .011 0169 0.203 0.265 0033 0.377 0.4
14、98 0082 0.377 0.498 Size R S 0170 0.203 0.625 0034 0.377 0.625 0083 0.377 0.625 0122 0.128 0.315 0171 0.261 0.497 0035 0.393 0.627 T = .008 0123 0.255 0.390 0172 0.390 0.465 0036 0.415 0.470 Size R S 0124 0.312 0.495 0173 0.530 1.000 0037 0.570 0.875 0084 0.100 0.200 T = .012 0174 0.594 0.734 0038 0
15、.753 0.975 0085 1.758 3.250 Size R S 0175 0.644 0.844 0039 1.000 1.375 0086 1.891 2.469 0125 0.128 0.250 0176 0.752 1.250 0040 1.250 1.375 0126 0.128 0.315 0177 1.202 1.310 0041 1.432 1.623 0127 0.198 0.450 0178 2.190 2.480 0042 2.190 2.438 0128 0.199 0.305 0043 2.435 2.873 0129 0.250 0.480 0044 3.0
16、50 3.313 0130 0.252 0.344 T = .004 0131 0.255 0.531 Size R S 0132 0.258 0.368 0045 0.135 0.234 0133 0.320 0.425 0046 0.170 0.360 0134 0.324 0.520 0047 0.195 0.468 0135 0.500 0.875 0048 0.252 0.344 0136 1.210 1.550 0049 0.375 0.500 0137 2.002 2.490 0138 2.002 2.740 0139 3.125 3.675 Provided by IHSNot
17、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59561A 3 3. SALIENT CHARACTERISTICS 3.1 Tolerances. Unless otherwise specified in the acquisition order (see 7.4(c), tolerances for the shims listed in table I shall be as shown below: Thickness Outside diameter .001
18、 to .005 - +10% Up to 1“ - +.003 .006 to .010 - +.0005 Over 1“ up to 3“ - +.005 .011 to .016 - +.001 Over 3“ - +.010 3.2 Materials. 3.2.1 Type I and II shims shall be aluminum alloy 5052, (unified numbering system (UNS) A95052), temper H38, in accordance with the American Society for Testing and Mat
19、erials (ASTM) B209, “Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate“ (DoD Adopted). 3.2.2 Type III shims shall be brass alloy UNS C26000, temper H02 (formerly half-hard), in accordance with the ASTM B36/B36M, “Standard Specification for Brass Plate, Sheet, Strip, And Rolled B
20、ar“ (DoD Adopted). 3.2.3 Type IV shims shall be austenitic CRES type 302, UNS S30200, temper 1/4 hard in accordance with ASTM A666 “Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar“ (DoD Adopted). 3.2.4 Type V shims shall be low-carbon s
21、teel, selected from designations 1010 through 1015 (UNS G10100 through G10150), in accordance with ASTM A568/A568M Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for(DoD Adopted). 3.3 Protective finish or su
22、rface treatment. 3.3.1 Type I shims shall be anodic coated in accordance with ASTM B580, “Standard Specification for Anodic Oxide Coatings on Aluminum“ (DoD Adopted). 3.3.2 Type II shims shall be chemically treated in accordance with MIL-DTL-5541, “Chemical Conversion Coatings on Aluminum and Alumin
23、um Alloys“. 3.3.3 Type III shims shall be protective finished as specified in MIL-F-495 unless the acquisition order provides for an alternative method (see 7.4(d). 3.3.4 Type IV shims shall be cleaned, descaled, and passivated in accordance with ASTM A967, “Standard Specification for Chemical Passi
24、vation Treatments for Stainless Steel Parts“ (DoD Adopted). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59561A 4 3.3.5 Type V shims shall be cadmium plated in accordance with ASTM B766, “Standard Specification for Electrodeposited Coatings of
25、 Cadmium“ (DoD Adopted). 3.4 Roughness Depth (Rmax). The product shall have a maximum Rmax of 63 in, determined in accordance with American Society of Mechanical Engineers (ASME) B46.1, “Surface Texture (Surface Roughness, Waviness, and Lay)“ (DoD Adopted). 3.5 Cracks. The shims shall be free from v
26、isible cracks, flaws, and pits in any location. A crack is a clean crystalline fracture passing through (transgranular) or across (intergranular) the grain boundaries without inclusion of foreign elements. 3.6 Workmanship. The shims shall be free from surface contamination, tool marks, and other imp
27、erfections which may adversely affect usability. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Foreign acquisi
28、tion restrictions. Unless otherwise indicated in the solicitation and resulting contract, the foreign acquisition restrictions in Section 252.225, Clause 252.225.7016 of the Defense Federal Acquisition Regulation Supplement (DFARS) apply to products described by this CID. 5. PRODUCT CONFORMANCE PROV
29、ISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace.
30、 The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. For acquisition purposes, the products shal
31、l be preserved, packed, and marked as specified in the acquisition order (see 7.4(e). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59561A 5 7. NOTES 7.1 Sources of documents. 7.1.1 DFARS and FAR. Copies of DFARS and FAR may be obtained from th
32、e Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of DFARS may be obtained from http:/www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html. Electronic copies of FAR may be obtained from https:/www.acquisition.gov/far/. 7.1.2 Federal standards. Copies of fe
33、deral standards may be obtained from General Services Administration, Federal Supply Service, Specification Section, 470 East LEnfant Plaza SW, Suite 8100, Washington, DC 20407. Electronic copies may be obtained from https:/assist.daps.dla.mil/. 7.1.3 Department of Defense specifications. Copies of
34、military specifications may be obtained from Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. Electronic copies may be obtained from https:/assist.daps.dla.mil/. 7.1.4 ASME standards. Copies of ASME standards may be obtained from the American Societ
35、y of Mechanical Engineers, Three Park Avenue, New York, NY 10016-5990. Electronic copies may be obtained from http:/www.asme.org/. 7.1.5 ASTM standards. Copies of ASTM standards may be obtained from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-29
36、59. Electronic copies may be obtained from http:/www.astm.org/. 7.2 Part or identification number (PIN). The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. Size (see table I) Type: 1 - Type I - Aluminum alloy,
37、 anodized 2 - Type II - Aluminum alloy, chemically treated 3 - Type III - Brass, black chemical finish 4 - Type IV - CRES, passivated 5 - Type V - Carbon steel, cadmium plated AAXXXXX X XXXX CID number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
38、A-A-59561A 6 7.3 National stock number (NSN). The NSNs listed below are assigned for the listed product types and sizes (see table I). Other NSNs may also correspond with this document. TABLE II. Assigned NSNs. Type Size code NSN IV 0002 5365-01-407-7890 IV 0004 5365-01-407-7900 IV 0008 5365-01-361-
39、9004 IV 0017 5365-01-334-1336 IV 0028 5365-01-407-7897 IV 0037 5365-01-339-4032 IV 0053 5365-01-407-7892 IV 0090 5365-01-407-7896 IV 0125 5365-01-407-7899 IV 0151 5365-01-407-7898 IV 0157 5365-01-379-5133 7.4 Ordering data. Acquisition documents must specify the following information: a. CID documen
40、t number, revision, and CID PIN b. Product type (see 2) and size (see table I) c. Tolerance, if different (see 3.1) d. Type III shim protective finish (see 3.3.3) e. Packaging requirements (see 6.1) MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodian: Army AR DLA - GS GSA - FAS Reviewe
41、rs: Army - AV, MI Preparing activity: DLA GS4 (Project 5365-2011-002) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
