1、INCHPOUND AA59590/13B 13 November 2010 SUPERSEDING AA59590/13A 23 October 2005 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .375 X .375 INCH BODY SIZE The General Services Administration has authorized the use of this commer
2、cial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specifica
3、tion sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /13 Applicable CID specification sheet B, C, H, R Finish * Mounting * * Length (see table I) W, D, E Configuration (see table II) Exampl
4、e: AA59590/13HV28W is the PIN for a hard black anodize finished, 2.8 inch (71.1 mm) long card holder. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners and a lockwasher and flat washer under the screw head for added resistance to loosening. SALIENT CHARACTERIS
5、TICS. Performance. Card holders shall hold the circuit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 Grms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance transfer between the c
6、ircuit card assembly and the heat sink surfaces. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1, 2, and 3, in tabl
7、e I, and AA59590. Actuating screw hex drive socket. The across flats dimension for the hex drive socket shall be as follows: .140 inch (3.56 mm) for mounting options “J“, “N“, “T“, “R“, “V“, and “S“ and 3.0 mm (0.118 inch) for mounting options “G“ and “M“. Nominal installation torque. When card hold
8、ers are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 16 to 20 inch-pounds (1.8 to 2.3 N-m) for assemblies using no options or option “W“ and 17 to 21 inch-pounds (1.9 to 2.5 N-m) for assemblies using options “E“ or “D“. Cold plate slot wid
9、th dimensions (when applicable). The recommended cold plate slot width to accommodate the circuit card assembly with attached card holder is .425 inch (10.80 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). AMSC N/A FSC 5998Provided by IHSNot for ResaleNo repro
10、duction or networking permitted without license from IHS-,-,-AA59590/13B 2 Inches mm Inches mm Inches mm .10 .20 2.5 5.1 .375 .385 9.5 9.8 .470 .70 11.9 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch
11、 (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .140 inch (3.56 mm) for mounting options “J“, “N“, “R“, “T“, “S“ and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 3.0
12、 mm (0.118 inch) across flats for mounting option “G“ and “M“. FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/13B 3 Finish. The finish designator shall be as specified in AA59590. The finishes avail
13、able for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as fol
14、lows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ or “R“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. See figure 1 for mounting hole spacing requirements
15、. Mounting hole locations (when required). When mounting holes are specified in the PIN, two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting hole,
16、 when present, shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .136 inch (3.45 mm) diameter through holes, countersunk 100 degrees by .190 to .200 inch (4.83 to 5.0
17、8 mm) diameter with an access/clearance counterbore hole of .190 to .200 inch (4.83 to 5.08 mm) diameter by .300 inch (7.62 mm) deep. Rivets. This card holder uses rivet style B as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length, expanded, and r
18、elaxed dimensions shall be as specified on figure 1. The length designator shall be as specified in AA59590 and the available lengths for this specification sheet are listed in table I. TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (
19、maximum) Dimension “B“ .03 (0.8) Dimension “C“ .005 (0.13) 28 2.8 (71.1) 3.10 (78.7) 2.05 (52.1) .65 (16.5) 33 3.3 (83.8) 3.60 (91.4) 2.55 (64.8) 1.15 (29.2) 38 3.8 (96.5) 4.10 (104.1) 3.05 (77.5) 1.65 (41.9) 43 4.3 (109.2) 4.60 (116.8) 3.55 (90.2) 2.15 (54.6) 48 4.8 (121.9) 5.10 (129.5) 4.05 (102.9
20、) 2.65 (67.3) 53 5.3 (134.6) 5.60 (142.2) 4.55 (115.6) 3.15 (80.0) 58 5.8 (147.3) 6.10 (154.9) 5.05 (128.3) 3.65 (92.7) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Configuration. The configuration of a card holder shall be as specified in table II. The d
21、etails of a particular configuration consist of those on figure 1, and may include those on figures 2 and 3. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. Provided by IHSNot for ResaleNo reproduction or networking permitted with
22、out license from IHS-,-,-AA59590/13B 4 TABLE II. Configurations. Configuration Applicable figures Hardware options 1 No added options W 1 and 2 Lockwasher and flat washer E 1 and 3 Screw self-locking element D 1, 2, and 3 Lockwasher, flat washer and screw self-locking element Lockwasher and flat was
23、her (see figure 2). A lockwasher and flat washer located under the screw head will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). FIGURE 2. Lockwasher a
24、nd flat washer details. Screw self-locking element (see figure 3). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classificatio
25、n and notes). FIGURE 3. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element configuration shall include a suffix “D“ in the PIN (see classification and notes). Provided by IHSNot
26、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/13B 5 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial
27、Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 R
28、obbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time
29、 of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procureme
30、nt to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 URL: 6
31、1081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 738
32、6194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table IV for CID PIN construction using o
33、ther available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/13B 6 TABLE III. Commercial part n
34、umber supersession data. PIN designator AA59590/13 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 BJ28 446B A2502.80H 3250BA2.80H BN28 446BA A2502.80 3250BA2.80 BT28 4
35、46BT A2502.80T0 3250BA2.80T0 BV28 446BS A2502.80T2 3250BA2.80T2 BG28 446BM MA2502.80TM2.5 3250MBA2.80TM2.5 BJ28E 446BL A2502.80HL 3240BA2.80HL BN28E 446BAL A2502.80L 3240BA2.80L BT28E 446BTL A2502.80T0L 3240BA2.80T0L BV28E 446BSL A2502.80T2L 3250BA2.80T2L BG28E 446BML MA2502.80TM2.5L 3250MBA2.80TM2.
36、5L BJ28W 446BLF WA2502.80H 3250WBA2.80H BN28W 446BLFA WA2502.80 3250WBA2.80 BT28W 446BLFT WA2502.80T0 3250WBA2.80T0 BV28W 446BLFS WA2502.80T2 3250WBA2.80T2 BG28W 446BLFM MWA2502.80TM2.5 3250MWBA2.80TM2.5 BJ28D 446BLFL WA2502.80HL 3250WBA2.80HL BN28D 446BLFAL WA2502.80L 3250WBA2.80L BT28D 446BLFTL WA
37、2502.80T0L 3250WBA2.80T0L BV28D 446BLFSL WA2502.80T2L 3250WBA2.80T2L BG28D 446BLFML MWA2502.80TM2.5L 3250MWBA2.80TM2.5L CJ28 446 2502.80H 3250CG2.80H CN28 446A 2502.80 3250CG2.80 CT28 446T 2502.80T0 3250CG2.80T0 CV28 446S 2502.80T2 3250CG2.80T2 CG28 446M M2502.80TM2.5 3250MCG2.80TM2.5 CJ28E 446L 250
38、2.80HL 3250CG2.80HL CN28E 446AL 2502.80L 3250CG2.80L CT28E 446TL 2502.80T0L 3250CG2.80T0L CV28E 446SL 2502.80T2L 3250CG2.80T2L CG28E 446ML M2502.80TM2.5L 3250MCG2.80TM2.5L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
39、AA59590/13B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/13 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 CJ28W 446LF W2502
40、.80H 3250WCG2.80H CN28W 446LFA W2502.80 3250WCG2.80 CT28W 446LFT W2502.80T0 3250WCG2.80T0 CV28W 446LFS W2502.80T2 3250WCG2.80T2 CG28W 446LFM MW2502.80TM2.5 3250MWCG2.80TM2.5 CJ28D 446LFL W2502.80HL 3250WCG2.80HL CN28D 446LFAL W2502.80L 3250WCG2.80L CT28D 446LFTL W2502.80T0L 3250WCG2.80T0L CV28D 446L
41、FSL W2502.80T2L 3250WCG2.80T2L CG28D 446LFML MW2502.80TM2.5L 3250MWCG2.80TM2.5L HJ28 446B3 HA2502.80H 3250BH2.80H HN28 446B3A HA2502.80 3250BH2.80 HT28 446B3T HA2502.80T0 3250BH2.80T0 HV28 446B3S HA2502.80T2 3250BH2.80T2 HG28 446B3M MHA2502.80TM2.5 3250MBH2.80TM2.5 HJ28E 446B3L HA2502.80HL 3250BH2.8
42、0HL HN28E 446B3AL HA2502.80L 3250BH2.80L HT28E 446B3TL HA2502.80T0L 3250BH2.80T0L HV28E 446B3SL HA2502.80T2L 3250BH2.80T2L HG28E 446B3ML MHA2502.80TM2.5L 3250MBH2.80TM2.5L HJ28W 446B3LF WHA2502.80H 3250WBH2.80H HN28W 446B3LFA WHA2502.80 3250WBH2.80 HT28W 446B3LFT WHA2502.80T0 3250WBH2.80T0 HV28W 446
43、B3LFS WHA2502.80T2 3250WBH2.80T2 HG28W 446B3LFM MWHA2502.80TM2.5 3250MWBH2.80TM2.5 HJ28D 446B3LFL WHA2502.80HL 3250WBH2.80HL HN28D 446B3LFAL WHA2502.80L 3250WBH2.80L HT28D 446B3LFTL WHA2502.80T0L 3250WBH2.80T0L HV28D 446B3LFSL WHA2502.80T2L 3250WBH2.80T2L HG28D 446B3LFML MWHA2502.80TM2.5L 3250MWBH2.
44、80TM2.5L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/13B 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/13 Vendor similar designator or type part number 1/ CAGE 18915
45、Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 RJ28 446CC R2502.80H 3250CC2.80H RN28 446CCA R2502.80 3250CC2.80 RT28 446CCT R2502.80T0 3250CC2.80T0 RV28 446CCS R2502.80T2 3250CC2.80T2 RG28 446CCM MR2502.80TM2.5 3250MCC2.80TM2.5
46、 RJ28E 446CCL R2502.80HL 3250CC2.80HL RN28E 446CCAL R2502.80L 3250CC2.80L RT28E 446CCTL R2502.80T0L 3250CC2.80T0L RV28E 446CCSL R2502.80T2L 3250CC2.80T2L RG28E 446CCML MR2502.80TM2.5L 3250MCC2.80TM2.5L RJ28W 446CCLF WR2502.80H 3250WCC2.80H RN28W 446CCLFA WR2502.80 3250WCC2.80 RT28W 446CCLFT WR2502.80T0 3250WCC2.80T0 RV28W 446CCLFS WR2502.80T2 3250WCC2.80T2 RG28W 446CCLFM MWR2502.80TM2.5 3250MWCC2.80TM2.5 RJ28D 446CCLFL WR2502.80HL 3250WCC2.80HL RN28D 446CCLFAL WR2502.80L 3250WCC2.80L RT28D 446CCLFTL WR2502.80T0L 3250WCC2.80T0L RV28D 446CCLFSL WR2502.80T2L 3250WCC2.80T2L RG28D 446CC
