1、INCHPOUND AA59590/16B 28 August 2010 SUPERSEDING AA59590/16A 9 November 2005 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .375 X .375 INCH BODY SIZE, WITH VISUAL LOCK INDICATION AND SCREW RETENTION The General Services Admin
2、istration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). T
3、his commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see NOTES). AA59590 CID number /16 Applicable CID specification sheet B, C, H, R Finish * Mounting * * Length (see table
4、 I) W, D, E Configuration Example: AA59590/16CG58 is the PIN for a chemical film finished, 5.8 inch (147.3 mm) long visual lock indicating card holder with a lock nut on the screw for captivation. The card holder also features three tapped mounting holes for use with metric M2.5 x 0.45 fasteners. SA
5、LIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card assembly firmly in its installed position. When the card holder is installed properly, it is capable of withstanding 60g/6ms of shock, 25 G-rms of vibration, and provides from 2 to 4 degrees C/W/inch thermal resistance tran
6、sfer between the circuit card assembly and the heat sink surfaces. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified on figures 1,
7、 2, 3, 4, and 5, in table I, and AA59590. Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card holder is in its relaxed (unlocked) state. When the card holder is in the unlocked (relaxed) state, the actuating end of the screw shall display a red band
8、 on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that the assembly is in the locked position, this red band shall be concealed. Screw retention (see figure 3). Card holders shall have a screw retention feature intended to prevent uninte
9、ntional disassembly of the card holder. The locknut shall be fabricated of a corrosion resistant material. Actuating screw hex drive socket. The across flats dimension for the hex drive socket shall be as follows: .140 inch (3.57 mm) for mounting options “J“, “N“, “T“, “R“, “V“, and “S“ and a metric
10、 dimension of 3.0 mm (0.118 inch) for mounting options “G“ and “M“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/16B 2 Inches mm Inches mm Inches mm Inches mm .27 .33 6.9 8.3 .375 .385 9.5 9.8 .40 .470 10.2 11.9 .50 .70 12
11、.7 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The across flats dimension for hex drive socket shall be .140 i
12、nch (3.57 mm) for mounting options “J“, “N“, “R“, “T“, “S“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 3.0 mm (.118 inch) across flats for mounting option “G“ and “M“. FIGURE 1. Relaxed and expanded dimensions. FIGURE 2. Visual lock indicator. Provided by
13、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/16B 3 FIGURE 3. Screw retaining self-locking nut (corrosion resistant) details. Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each c
14、ard holder shall be as follows: 16 to 20 inchpounds (1.8 to 2.3 Nm) for assemblies using no options or option “W“ and 17 to 21 inchpounds (1.9 to 2.5 Nm) for assemblies using options “E“ or “D“. Cold plate slot width dimensions (when applicable). The recommend cold plate slot width to accommodate th
15、e circuit card assembly with attached card holder is .425 inch (10.80 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Finish. The finish designator shall be as specified in AA59590. The finishes available for this CID specification sheet are as follows: “B“ (b
16、lack anodize), “C“ (gold chemical film), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “
17、R“ or “T“ (tapped 080 UNF 2B holes), “V“ or “S“ (tapped 256 UNC 2B holes), or “G“ or “M“ (tapped M2.5 x.45 metric holes). Card holders using mounting option “J“ may be shipped unassembled. See figure 1 and table I for mounting hole spacing requirements. Rivet mounting holes. The holes used for rivet
18、 mounting shall be .136 inch (3.45 mm) diameter through holes, countersunk 100 degrees by .190 to .200 inch (4.83 to 5.08 mm) diameter with an access/clearance counterbore hole of .190 to .200 inch (4.83 to 5.08 mm) diameter by .300 inch (7.62 mm) deep. Rivets. This card holder uses rivet style B as
19、 specified in AA59590 when rivet mounting is used. Mounting hole locations (when specified). Two mounting holes are required on card holders less than 5.30 inches (134.6 mm) in length. Three mounting holes are required on card holders 5.30 inches (134.6 mm) or greater in length. The third mounting h
20、ole, when present, shall be centered on the mounting body. See figure 1 and table I for mounting hole locations and spacing requirements. Length, expanded, and relaxed dimensions. The length, expanded, and relaxed dimensions shall be as specified on figure 1. The length designator shall be as specif
21、ied in AA59590 and the available lengths are listed in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/16B 4 TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5) Dimension “A“ (maximum) D
22、imension “B“ .03 (0.8) Dimension “C“ .005 (0.13) 28 2.8 (71.1) 3.45 (87.6) 2.05 (52.1) .65 (16.5) 33 3.3 (83.8) 3.95 (100.3) 2.55 (64.8) 1.15 (29.2) 38 3.8 (96.5) 4.45 (113.0) 3.05 (77.5) 1.65 (41.9) 43 4.3 (109.2) 4.95 (125.7) 3.55 (90.2) 2.15 (54.6) 48 4.8 (121.9) 5.45 (138.4) 4.05 (102.9) 2.65 (6
23、7.3) 53 5.3 (134.6) 5.95 (151.1) 4.55 (115.6) 3.15 (80.0) 58 5.8 (147.3) 6.45 (163.8) 5.05 (128.3) 3.65 (92.7) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Configuration. The configuration of a card holder shall be as specified in table II. The de
24、tails of a particular configuration consist of those on figures 1, 2 and 3, and may include those on figures 4 and 5. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configurations. Configuration Applicable figures Hardw
25、are options 1, 2, and 3 No added options W 1, 2, 3 and 4 Lockwasher and flat washer E 1, 2, 3 and 5 Screw self-locking element D 1, 2, 3, 4 and 5 Lockwasher, flat washer and screw self-locking element Lockwasher and flat washer (see figure 4). A lockwasher and flat washer located under the screw hea
26、d will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer option shall include a suffix “W” in the PIN (see classification and notes). FIGURE 4. Lockwasher and flat washer details. Provided by IHSNot for ResaleNo reproduction
27、or networking permitted without license from IHS-,-,-AA59590/16B 5 Screw self-locking element (see figure 5). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock and vibration. Card holders requiring a screw self-locking element shall include
28、 a suffix “E“ in the PIN (see classification and notes). FIGURE 5. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classific
29、ation and notes). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece,
30、Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Commercial products
31、. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet
32、the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher
33、A Division of Pentair Electronic Packaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 (URL): 61081 Calmark A Division of Pentair Electronic Packaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Fre
34、e: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
35、rom IHS-,-,-AA59590/16B 6 Ordering data. Ordering data is as specified in AA59590. Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See ta
36、ble IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. PIN designator AA59590/16 Vendor similar designa
37、tor or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 BJ28 44VI6BLN VA250CR2.80HR 3250VBA2.80HR BN28 44VI6BLNA VA250CR2.80R 3250VBA2.80R BT28 44VI6BLNT VA250CR2.80T0R 3250VBA2.80T0R BV28 44VI6BLNS
38、 VA250CR2.80T2R 3250VBA2.80T2R BG28 44VI6BLNM MVA250CR2.80TM2.5R 3250MVBA2.80TM2.5R BJ28E 44VI6BLNL VA250CR2.80HLR 3250VBA2.80HLR BN28E 44VI6BLNAL VA250CR2.80LR 3250VBA2.80LR BT28E 44VI6BLNTL VA250CR2.80T0LR 3250VBA2.80T0LR BV28E 44VI6BLNSL VA250CR2.80T2LR 3250VBA2.80T2LR BG28E 44VI6BLNML MVA250CR2.
39、80TM2.5LR 3250MVBA2.80TM2.5LR BJ28W 44VI6BLFLN WVA250CR2.80HR 3250VWBA2.80HR BN28W 44VI6BLFLNA WVA250CR2.80R 3250VWBA2.80R BT28W 44VI6BLFLNT WVA250CR2.80T0R 3250VWBA2.80T0R BV28W 44VI6BLFLNS WVA250CR2.80T2R 3250VWBA2.80T2R BG28W 44VI6BLFLNM MWVA250CR2.80TM2.5R 3250MVWBA2.80TM2.5R BJ28D 44VI6BLFLNL W
40、VA250CR2.80HLR 3250VWBA2.80HLR BN28D 44VI6BLFLNAL WVA250CR2.80LR 3250VWBA2.80LR BT28D 44VI6BLFLNTL WVA250CR2.80T0LR 3250VWBA2.80T0LR BV28D 44VI6BLFLNSL WVA250CR2.80T2LR 3250VWBA2.80T2LR BG28D 44VI6BLFLNML MWVA250CR2.80TM2.5LR 3250MVWBA2.80TM2.5LR See footnote at end of table. Provided by IHSNot for
41、ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/16B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/16 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Ve
42、ndor similar designator or type part number 1/ CAGE 5BG68 CJ28 44VI6LN V250CR2.80HR 3250VCG2.80HR CN28 44VI6LNA V250CR2.80R 3250VCG2.80R CT28 44VI6LNT V250CR2.80T0R 3250VCG2.80T0R CV28 44VI6LNS V250CR2.80T2R 3250VCG2.80T2R CG28 44VI6LNM MV250CR2.80TM2.5R 3250MVCG2.80TM2.5R CJ28E 44VI6LNL V250CR2.80H
43、LR 3250VCG2.80HLR CN28E 44VI6LNAL V250CR2.80LR 3250VCG2.80LR CT28E 44VI6LNTL V250CR2.80T0LR 3250VCG2.80T0LR CV28E 44VI6LNSL V250CR2.80T2LR 3250VCG2.80T2LR CG28E 44VI6LNML MV250CR2.80TM2.5LR 3250MVCG2.80TM2.5LR CJ28W 44VI6LFLN WV250CR2.80HLR 3250WVCG2.80HR CN28W 44VI6LFLNA WV250CR2.80R 3250WVCG2.80R
44、CT28W 44VI6LFLNT WV250CR2.80T0R 3250WVCG2.80T0R CV28W 44VI6LFLNS WV250CR2.80T2R 3250WVCG2.80T2R CG28W 44VI6LFLNM MWV250CR2.80TM2.5R 3250MVWCG2.80TM2.5R CJ28D 44VI6LFLNL WV250CR2.80HLR 3250VWCG2.80HLR CN28D 44VI6LFLNAL WV250CR2.80LR 3250VWCG2.80LR CT28D 44VI6LFLNTL WV250CR2.80T0LR 3250VWCG2.80T0LR CV
45、28D 44VI6LFLNSL WV250CR2.80T2LR 3250VWCG2.80T2LR CG28D 44VI6LFLNML MWV250CR2.80TM2.5LR 3250MVWCG2.80TM2.5LR HJ28 44VI6B3LN VHA250CR2.80HR 3250VBH2.80HR HN28 44V6B3LNA VHA250CR2.80R 3250VBH2.80R HT28 44VI6B3LNT VHA250CR2.80T0R 3250VBH2.80T0R HV28 44VI6B3LNS VHA250CR2.80T2R 3250VBH2.80T2R HG28 44VI6B3
46、LNM MVHA250CR2.80TM2.5R 3250MVBH2.80TM2.5R HJ28E 44VI6B3LNL VHA250CR2.80HLR 3250VBH2.80HLR HN28E 44VI6B3LNAL VHA250CR2.80LR 3250VBH2.80LR HT28E 44VI6B3LNTL VHA250CR2.80T0LR 3250VBH2.80T0LR HV28E 44VI6B3LNSL VHA250CR2.80T2LR 3250VBH2.80T2LR HG28E 44VI6B3LNML MVHA250CR2.80TM2.5LR 3250MVBH2.80TM2.5LR S
47、ee footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/16B 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/16 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 HJ28W 44VI6B3LFLN WVHA250CR2.80HR 3250VWBH2.80HR HN28W 44VI6B3LFLNA WVHA250CR2.80R 3250
