1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation, DLA Aviation-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can
2、 change, you may want to verify the currency of this address information using the ASSIST database at https:/assist.dla.mil. AMSC N/A FSC 6850 NOT MEASUREMENT SENSITIVE A-A-59601E 10 October 2012 SUPERSEDING A-A-59601D 28 February 2007 COMMERCIAL ITEM DESCRIPTION DRY CLEANING AND DEGREASING SOLVENT,
3、 PD680 The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers hydrocarbon solvents used in the dry cleaning and coatings industries and in the military for degreasing and cleanin
4、g painted or unpainted metal parts. 2. CLASSIFICATION. The dry cleaning solvent shall be of the following types and sizes listed below. 2.1 Type. The type of cleaning solvent shall be as specified (see 7.3(b). Type I - Regular (Stoddard solvent) Type II - High flash point Type III - Low odor with ve
5、ry high flash point (200 F or more) 2.2 Size. The solvent unit of issue size shall be one of the coded sizes listed in table I (see 7.3(c). TABLE I. Product size. Size code Size/unit of issue A Bulk B 4 ounce C 1-pint can D 1 quart E 1 gallon F 5-gallon can G 55-gallon drum 3. SALIENT CHARACTERISTIC
6、S Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59601E 2 3.1 Properties. The solvent shall have the properties listed in table II. TABLE II. Dry cleaning and degreasing solvent properties. Characteristics Test method Type I Type II Type III Fla
7、sh point, C, min. ASTM D56 38.0 (100 F) 60.0 (140 F) 93.3 (200 F) Distillation, C: Initial boiling point, min. 50% recovered Dry point, max. ASTM D86 149 Report 208 177 Report 211 220 Report 295 Aniline point, C ASTM D611 57 to 74 57 to 74 73 to 89 Kauri-butanol value ASTM D1133 29 to 45 29 to 45 27
8、 to 45 Allowable constituents, (% by volume)1: (a) Solvent with olefinic or cyclo-olefinic unsaturation, max. (b) Aromatic compounds with eight or more carbon atoms, except ethylbenzene, max. (c) Total of ethylbenzene, toluene and branched chain ketones, max. (d) Total of (a) + (b) + (c), max. EPA M
9、ethod 311 5 8 20 20 5 8 20 20 0.8 0.8 1 1 Total chlorine content (ppm), max.2100 100 100 Total phenol content (ppm), max. EPA Method 420.1 0.5 0.5 0.5 Apparent specific gravity, 60/60 F ASTM D1298 0.754 to 0.820 0.754 to 0.820 0.754 to 0.820 Non-volatile residue (mg/100 ml), max. ASTM F331 10 10 10
10、Color, min. ASTM D156 25 25 30 Odor3ASTM D1296 Characteristic and non-residual Characteristic and non-residual Low and non-residual Corrosion, copper, max. ASTM D130 2a 2a 2a Acidity ASTM D847 Neutral Neutral Neutral Doctor test ASTM D235 Negative Negative Negative Vapor pressure, torr at 20 C, max.
11、 ASTM D2879 - - 0.40 Viscosity, mm2/s at 25 C, max. ASTM D445 - - 5.0 1Type I and II maximum limits are as defined in Rule 102, South Coast Air Quality Management District regulations. 2The total chlorine content of the solvent shall be determined by a gas chromatographic method, microcoulometric me
12、thod, or by the use of a portable test kit for the quantitative analysis of chlorine. 3Samples of A-A-59601 having satisfactory odor characteristics shall be used as reference standards. 3.2 Appearance. The solvent shall be clear and free from suspended matter and undissolved water when observed bet
13、ween 15.6 C and 25.6 C (60 F and 78 F). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59601E 3 3.3 Materials. The hydrocarbon solvent shall be a virgin grade or recycled solvent derived from petroleum distillates, fractions from reclaiming and
14、re-refining processes, or a mixture of these fractions. The resultant solvent must be produced in such a manner as is necessary to meet the specified requirements. 3.4 Toxicity and carcinogenicity. The solvent shall have no adverse effect on human health when used as intended. The solvent shall cont
15、ain no chemicals listed as carcinogens. Any carcinogenic components in the solvent in a concentration of 0.1 percent or greater by weight or by volume will be regarded as the presence of a carcinogen in the solvent. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encour
16、aged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Material safety data sheet (MSDS). An MSDS shall be prepared and furnished in accordance with Title 29 Code of Federal Regulations (CFR), part 1910.
17、1200, “Hazard Communication“, and submitted as directed in the contract or order at time of acquisition award. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, s
18、tandards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The product offered must have been previously sold either to the government or on the c
19、ommercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specified in the acquisition order (see 7.3(d). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59601E 4 7. NOTES 7.1 Part or id
20、entification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. 7.2 Sources of documents. 7.2.1 CFR and FAR. Copies of CFR and FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7
21、954. Electronic copies of CFR documents may be obtained from http:/www.access.gpo.gov/. Electronic copies of FAR documents may be obtained from https:/www.acquisition.gov/far/. 7.2.2 EPA methods. EPA methods are available on the Internet at http:/www.epa.gov/. 7.2.3 SCAQMD rules. South Coast Air Qua
22、lity Management District rules are available at http:/www.aqmd.gov/. 7.2.4 ASTM standards. Copies of ASTM standards may be obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm
23、.org/. 7.3 Ordering data. The acquisition order should specify the following: a. CID document number, revision, and CID PIN. b. Type (see 2.1). c. Size and unit of issue (see 2.2). d. Preservation, packing, and marking (see 6.1). 7.4 International standardization agreement. Certain provisions of thi
24、s CID are the subject of international standardization agreement NATO STANAG 1135 Annex C. When revision or cancellation of this CID is proposed that will modify the international agreement concerned, the preparing activity will take appropriate action through international standardization channels,
25、 including departmental standardization offices, to change the agreement or make other appropriate accommodations. AA59601 X X CID number Type: 1 - Type I - Regular (Stoddard solvent) 2 - Type II - High flash point 3 - Type III - Low odor with very high flash point solvent (200 F or more) Size: (see
26、 2.2) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59601E 5 7.5 Intended use. 7.5.1 Type I. Type I (Stoddard solvent) is intended for use as dry cleaning solvent. When used indoors, ventilation shall be sufficient to prevent the accumulation o
27、f vapors above required exposure limits. 7.5.2 Type II. Type II (high flash point solvent) is intended where a solvent with a higher flash point is desired. It is recommended over type I for safety and regulatory reasons. When type II solvent is used indoors, ventilation shall be sufficient to preve
28、nt the accumulation of vapors above required exposure limits. 7.5.3 Type III. Type III (low odor with very high flash point solvent) is intended for use where confined atmospheric conditions require a cleaner that conforms to the Federal Governments directives for reducing hazardous materials. 7.6 N
29、ational stock number (NSN). The list of assigned NSNs in table III corresponds to this CID. The list may not be indicative of all possible NSNs associated with the CID. TABLE III. Dry cleaning and degreasing solvent NSNs. Assigned NSN Type Size Military symbol/NATO code 6850-00-264-9039 I Bulk N/A1
30、6850-00-281-3061 I 4 ounce N/A 6850-00-664-5685 I 1 quart N/A 6850-00-281-1985 I 1 gallon N/A 6850-00-264-9038 I 5-gallon can N/A 6850-00-285-8012 I 55-gallon drum N/A 6850-00-637-6135 II Bulk N/A 6850-00-110-4498 II 1-pint can N/A 6850-00-274-5421 II 5-gallon can N/A 6850-00-285-8011 II 55-gallon d
31、rum N/A 6850-01-331-3349 III 5-gallon can N/A 6850-01-331-3350 III 55-gallon drum N/A 1Not applicable Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59601E 6 7.7 Subject term (key word) listing. aromatic compounds chlorine ethylbenzene hydrocarb
32、on ketone petroleum distillates phenol Stoddard toluene MILITARY INTERESTS: Custodians: Navy AS Air Force 68 CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS Preparing Activity: DLA GS3 (Project 6850-2012-008) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
