1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you m
2、ay want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 3110 METRIC A-A-59634B 7 December 2010 SUPERSEDING A-A-59634A 6 August 2004 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 33 THROU
3、GH 45, DIMENSION SERIES 03 The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers metric, single row, angular contact, annular ball bearings for general-purpose use. These bearin
4、gs are not intended for use in critical aeronautical or critical special precision applications. 2. CLASSIFICATION. The ball bearings shall be classified by the class, sizes, cage materials, shield and seal configurations, precision tolerances, lubricant and preservative requirements, and duplex mou
5、nting configurations listed below: Class 2 - dimension series 03 Sizes - bearing dimensions (see table I) Cage materials (see table II) Shield and seal configurations (see table III) Precision tolerances (see table IV) Lubricant and preservative requirements (see table V) Duplex mounting configurati
6、ons (see table VI) 3. SALIENT CHARACTERISTICS 3.1 Dimensions. Bearing boundary dimensions shall conform to the requirements specified in table I for each of the coded bearing sizes. The listed dimensions conform to the requirements Provided by IHSNot for ResaleNo reproduction or networking permitted
7、 without license from IHS-,-,-A-A-59634B 2 specified for the listed bearing sizes from dimension series 03 in the American Bearing Manufacturers Association (ABMA) Standard 20, “Radial Bearings of Ball, Cylindrical Roller, and Spherical Roller Types, Metric Design“. The bearing size shall be as spec
8、ified in the acquisition order (see 7.3(b). For unlisted bearing sizes, the dimensional and dynamic load rating requirements should also be specified in the acquisition order. TABLE I. Dimensional requirements (ABMA series 03). Bearing size code Bore diameter (mm) Outside diameter (mm) Width (mm) Ch
9、amfer r/min. (mm) Minimum shaft shoulder diameter 1(mm) Dynamic load rating (minimum) (lbs.) 00 10 35 11 0.6 15 50001 12 37 12 1.0 18 1,78002 15 42 13 1.0 21 1,98503 17 47 14 1.0 23 2,67004 20 52 15 1.1 27 2,91005 25 62 17 1.1 32 3,77006 30 72 19 1.1 37 5,07007 35 80 21 1.5 43.5 6,19008 40 90 23 1.5
10、 48.5 7,41009 45 100 25 1.5 53.5 9,29510 50 110 27 2.0 60 10,79011 55 120 29 2.0 65 12,38512 60 130 31 2.1 72 14,07513 65 140 33 2.1 77 15,87514 70 150 35 2.1 82 18,30515 75 160 37 2.1 87 19,82016 80 170 39 2.1 92 21,37017 85 180 41 3.0 99 22,95018 90 190 43 3.0 104 24,56519 95 200 45 3.0 109 26,205
11、20 100 215 47 3.0 114 29,50521 105 225 49 3.0 119 31,30522 110 240 50 3.0 124 33,09524 120 260 55 3.0 134 38,89026 130 280 58 4.0 148 42,81028 140 300 62 4.0 158 46,83030 150 320 65 4.0 168 50,96032 160 340 68 4.0 178 52,90534 170 360 72 4.0 188 57,86536 180 380 75 4.0 198 62,41038 190 400 78 5.0 21
12、2 64,52040 200 420 80 5.0 222 70,0201 Listed for reference purposes only. Shoulder height shall be determined to provide sufficient clearance for the direct application of bearing removal force against the bearing inner ring. If the required minimum clearance is not available, an alternative non-des
13、tructive bearing removal capability shall be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 3 3.2 Materials. 3.2.1 Rings. The bearing ring material shall be chromium-alloy steel 52100 (UNS G52986) as specified in ASTM Internatio
14、nal (ASTM) A295/A295M, “Standard Specification for High-Carbon Anti-Friction Bearing Steel“. The finished rings shall not exceed the associated billet material inclusion rating also specified in ASTM A295/A295M. Ring hardness shall be at least 58 HRC as defined in ASTM E18, “Standard Test Methods fo
15、r Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials“. The grain size of the ring material shall be determined in accordance with ASTM E112, “Standard Methods for Determining Average Grain Size“. 3.2.2 Balls. The bearing ball material shall be chromium-alloy steel 52100 (UNS G
16、52986) as specified in ASTM A295/A295M. The finished balls shall not exceed the associated billet material inclusion rating, which is also specified in ASTM A295/A295M. Balls shall be through-hardened no less than 60 HRC and no more than 67 HRC as defined in ASTM E18. The grain size of the ball mate
17、rial shall be determined in accordance with ASTM E112. 3.2.3 Cage. The bearing cage material shall be impervious to deterioration from any lubricant, preservative, solvent, or other chemical substance expected to contact the bearing during normal use or storage. Similarly, the material shall not cau
18、se any chemical deterioration of any other bearing component. Metallic cage materials shall operate from -40 F to 250 F (-40 C to 121 C). Non-metallic cage materials shall operate from -20 F to 250 F (-30 C to 121 C). Unless otherwise specified in the acquisition order, the cage material shall be on
19、e of the optional coded types listed in table II (see 7.3(c). TABLE II. Cage materials. Code 1Material type J Pressed steel M Machined bronze or brass P Molded plastic (nylon 6/6 or equal) T Machined non-metallic (phenolic) Y Pressed brass X Other (specify in acquisition order) 1 No significant chan
20、ges from FF-B-171/30. 3.2.4 Shields and seals. Unless otherwise specified in the acquisition order, the shield and seal configuration for the bearing shall be one of the coded options listed in table III (see 7.3(d). The acquisition order shall state which side of the outer ring (heavy shoulder or c
21、ounterbore side) the shield or seal is to be located (see 7.3(e). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 4 TABLE III. Shield and seal configurations. Code 1Configuration option A Open X Other (specify in acquisition order)1 No sig
22、nificant changes from FF-B-171/30. 3.2.4.1 If a single shield or seal is required, the shield or seal material shall be as recommended by the manufacturer, unless otherwise specified in the acquisition order (see 7.3(f). The material shall be impervious to deterioration from any lubricant, preservat
23、ive, solvent, or other chemical substance expected to contact the bearing during normal use or storage. Similarly, the material shall not cause any chemical deterioration of any other bearing component. The shield or seal material shall remain functionally effective at a minimum temperature range of
24、 -20 F to 250 F (-30 C to 121 C) for non-metallic and -40 F to 250 F (-40 C to 121 C) for metallic materials. 3.3 Precision tolerance. The bearing precision tolerance level shall conform to Annular Bearing Engineers Committee (ABEC) class ABEC-1, ABEC-3, ABEC-5, or ABEC-7 as defined in ABMA Standard
25、 20. The tolerance class shall be one of the coded options listed in table IV (see 7.3(g). TABLE IV. Precision tolerance requirements. Code Tolerance class B ABEC-1 F ABEC-3 K ABEC-5 P ABEC-7 3.3.1 Bearing precision tolerance levels and internal clearances may be affected by the addition of shields
26、and/or seals. Manufacturers/suppliers should be consulted for availability of desired precision tolerances when shields and/or seals are required. 3.4 Lubrication and preservation requirements. Unless otherwise specified in the acquisition order, the bearing lubricant or preservative requirement sha
27、ll be as selected from the approved coded options listed in table V (see 7.3(h). When grease fill is required, the bearing void (the airspace between the inner and outer rings of the assembled bearing) shall be 25 to 50 percent filled. Bearing preservative shall be in accordance with MIL-DTL-197, “P
28、ackaging of Bearings, Associated Parts and Subassemblies“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 5 TABLE V. Lubricant and preservative requirements. Code Lubricant or preservative compound B Grease in accordance with MIL-PRF-8132
29、2 E Grease in accordance with DOD-G-24508 H Grease in accordance with MIL-PRF-23827 L Grease with SRI-2 or qualified equivalent S No fill T Preservation compound in accordance with MIL-DTL-197 X Other (specify in the acquisition order) 3.5 Duplex mounting. When required, the adjoining faces of beari
30、ngs used in duplex applications shall be match ground and marked for proper mounting. The duplex mounting configuration shall be one of the coded options listed in table VI. If required, the duplex mounting configuration shall be specified in the acquisition order (see 7.3(i). TABLE VI. Duplex mount
31、ing. Code Configuration option F Face to face B Back to back T Tandem U Universal (F, B, or T)3.6 Preload. Preload requirements shall be listed in the acquisition order (see 7.3(j). 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to
32、 the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Foreign acquisition restrictions. Unless otherwise indicated in the solicitation and resulting contract, the foreign acquisition restrictions in Section 252.225, Clause 252.225.7016,
33、 of the Defense Federal Acquisition Regulation Supplement (DFARS) apply to products described by this CID. 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, stand
34、ards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 6 5.2 Ma
35、rket acceptability. The products offered must have been previously sold either to the government or on the commercial market. 6. PACKAGING 6.1 Preservation, packing, and marking. Unless otherwise specified in the acquisition order, the bearings supplied shall be preserved, packed, and marked in acco
36、rdance with MIL-DTL-197 (see 7.3(k). 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. AA59634 2 08 J A B B U Example of reference part number: Duplex mounting code (see table VI) Lubrica
37、nt and preservative code (see table V) Precision tolerance code (see table IV) Shield and seal code (see table III) Cage material code (see table II) Bearing size code (see table I) Class 2 - dimension series 03 CID numberAA59634 - 2 08 J A B B U indicates: boundary dimension series 03; bore diamete
38、r 40 mm, outside diameter 90 mm, width 28 mm; pressed steel cage; open, no shield or seal; ABEC-1 tolerance class; filled with grease in accordance with MIL-PRF-81322; universal duplex mounting. 7.2 Sources of documents. 7.2.1 DFARS and FAR. Copies of DFARS and FAR may be obtained from the Superinte
39、ndent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of DFARS may be obtained from http:/www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html. Electronic copies of FAR may be obtained from https:/www.acquisition.gov/far/. 7.2.2 Military specifications. Copies of militar
40、y specifications may be obtained from Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. Electronic copies may be obtained from https:/assist.daps.dla.mil/. 7.2.3 ABMA standards. Copies of ABMA standards may be obtained from the American Bearing Manuf
41、acturers Association, 2025 M Street NW, Suite 800, Washington, DC 20036. Electronic copies may be obtained from http:/www.abma-dc.org/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 7 7.2.4 ASTM standards. Copies of ASTM standards may be
42、 obtained from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies may be obtained from http:/www.astm.org/. 7.3 Ordering data. The acquisition order should specify the following information: a. CID document number, revision, and CID PIN. b.
43、Bearing size (with dimension/load requirements if size is unlisted), if different (see 3.1). c. Cage material type (see 3.2.3). d. Shield and seal configuration (see 3.2.4). e. Location of shield or seal (see 3.2.4). f. Shield or seal material (see 3.2.4.1). g. Precision tolerance requirement (see 3
44、.3). h. Lubricant and preservative requirements (see 3.4). i. Duplex mounting configuration, if required (see 3.5). j. Preload requirement, if required (see 3.6). k. Preservation, packing, and marking requirements (see 6.1). 7.4 Codes cross-reference. Tables VII, VIII, and IX contain cross-reference
45、 data for the PIN information as listed in FF-B-171/30 and this CID. 7.4.1 Bearing class designations. The CIDs replacing 33 of 37 associated specification sheets of FF-B-171 have been assigned class codes corresponding to ABMA dimension series. Table VII lists the FF-B-171 specification sheets, the
46、 corresponding dimension series, the CID class codes, and the replacement CIDs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 8 TABLE VII. Federal specification to CID cross-reference. FF-B-171 specification sheets ABMA dimension series
47、CID classcodes Replacement CID numbers 1 02, 03, 10 1, 2, 4 A-A-59581 2 19 5 A-A-59582 3 10 4 A-A-59583 4 02 1 A-A-59584 5 03 2 A-A-59585 6 04 3 A-A-59586 7 02 1 A-A-59587 8 03 2 A-A-59589 9 32 8 A-A-59595 10 33 9 A-A-59596 11 02 1 A-A-59597 12 03 2 A-A-59598 13 22 6 A-A-59599 14 23 7 A-A-59600 15 1
48、9 - Canceled 16 10 - Canceled 17 02 - Canceled 18 03 - Canceled 19 19 5 A-A-59623 20 10 4 A-A-59624 21 02 1 A-A-59625 22 03 2 A-A-59626 23 04 3 A-A-59627 24 10 4 A-A-59628 25 02 1 A-A-59629 26 03 2 A-A-59630 27 04 3 A-A-59631 28 10 4 A-A-59632 29 02 1 A-A-59633 30 03 2 A-A-59634 31 04 3 A-A-59635 32
49、 32 8 A-A-59636 33 33 9 A-A-59637 34 32 8 A-A-59638 35 33 9 A-A-59639 36 32 8 A-A-59640 37 33 9 A-A-59641 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59634B 9 TABLE VIII. Radial internal clearance and ABEC tolerance codes. FF-B-171/30 codes A-A-59634B codes Code Rad
