1、 INCH-POUND A-A-59708 December 12, 2001 SUPERSEDING CCC-D-950F June 26, 1989 COMMERCIAL ITEM DESCRIPTION CLOTH, COTTON, AFTERTREATED WATER- REPELLANT, WATER-REPELLANT, AND MILDEW RESISTANT, MILDEW RESISTANT The General Services Administration has authorized the use of this commercial item descriptio
2、n in preference to Federal Specification CCC-D-950 1. SCOPE This specification governs dyeing and water-repellent and mildew-resistant after treating of cotton cloth. 2 CLASSIFICATION 2.1 Types. The finished cloth shall be of the following types Type: I - Water -repellent after treated II - Water -r
3、epellent and mildew resistant after treated III - Mildew resistant after treated Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directo
4、rate, Attn.: DSCP-COCT, 700 Robbins Ave., Philadelphia PA., 19111-5092. AMSC N/A DISTRIBUTION STATEMENT A FSC 8305 Approved for public release distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 3. SALIENT CHARACTERIS
5、TICS 3.1 Standard sample. The cloth shall match the standard sample for shade and appearance and shall be equal to the standard sample with respect to all characteristics for which the standard sample is referenced 3.2 Materials. The specification governing the requirements for the untreated cloth t
6、o be dyed or treated under this specification shall be as cited in the applicable procurement document . 3.2.1 Cloth. The cloth shall conform to the requirements of the applicable specification for the untreated material prior to, and after aftertreating, except as otherwise indicated herein. 3.3 Ph
7、ysical requirements. Tests for the physical properties of the finished cloth specified herein shall be conducted as follows. The physical and chemical values specified in section 3 (except where otherwise indicated), apply to the results of determinations made on a sample unit for test purposes as s
8、pecified in the applicable test method. The sample unit for testing shall be 1-1/2 yards of the untreated cloth, 1/2 yard of cloth prior to treatment and 3 linear yards of the finished cloth, all full width of the material. When shrinkage is required, the sample unit (finished cloth) shall be 5 line
9、ar yards. The sample size shall be as shown in table below. the sample unit shall be 1/4 yard and the sample size shall be five for all lots less than 22,001 units in size and eight for all lots over 22,000 units in size. The lot size shall be expressed in units of 1 yard. The lot shall be unaccepta
10、ble If one or more sample units fail to meet any specified requirement, or when the lot average determination for change in yarns per inch or breaking strength does not meet specific requirements. All test reports shall contain the individual values utilized in expressing the final results. Lot size
11、 in yards Sample size (sample units) 800 or less 2 801 up to and including 22,000. 3 22,001 and over 5 3.3.1 Finished width. The minimum overall width of the finished cloth shall be as specified (see 6.2), with the following tolerances: Specified width of finshed cloth Tolerance Up to 45 inches Plus
12、 1/4 minus 1/4 46 inches to 58 inches Plus 3/8 minus 1/4 59 inches to 66 inches Plus 5/8 minus 3/8 Over 66 inches Plus 3/4 minus 1/2 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 3.3.2 Yarns per inch. 3.3.2.1 Warp. The warp yarns per inc
13、h of the finished cloth shall be not less than 95 percent of the warp yarns per inch of the untreated cloth when tested in accordance with ASTM-D-3775 Standard Test Method for Fiber Count of Woven Fabric. . 3.3.2.2 Filling. The filling yarns per inch of the finished cloth shall be not less than 90 p
14、ercent of the filling yarns per inch of the untreated cloth when tested in accordance with ASTM-D-3775 Standard Test Method for Fiber Count of Woven Fabric. 3.3.3 Breaking strength. The breaking strength of the finished cloth shall be not less than 90 percent of the breaking strength of the untreate
15、d cloth in the warp direction and not less than 85 percent of the breaking strength of the untreated cloth in the filling direction when tested in accordance with ASTM-D-5034 Standard Test method for Breaking Strength and Elongation of textile methods. G-E or G-T. 3.3.4 Shrinkage. When preshrunk clo
16、th is specified in the applicable cloth document, the residual shrinkage shall be more not more than 2.0 percent in either the warp direction or the filling direction when tested in accordance with ASTM-D-96 test Ic, D, Shrinkage in Laundering: Cotton Linen AATCC Crockmeter Method. 3.5 After treatin
17、g. 3.5.1 Type I- Water repellant after treated. The cloth shall have a commercial acceptable water repellant finish. 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 3.5.1.1 Hydrostatic resistance. The hydrostatic resistance of the followin
18、g listed, finished cloths shall meet the requirements specified when tested in accordance with AATCC 127 Water Resistance: Hydrostatic Pressure Test. Hydrostatic height (centimeters) Average Single value (minmum) (minmum) Army ducks, 10 oz. per sq. yd. and over 30 25 Army ducks, under 10 oz. per sq.
19、 yd. 25 20 Numbered ducks: No. 10 and lighter 30 25 No. 8 and heavier 35 30 Flat ducks 25 20 Twills 30 25 3.5.1.2 Spray rating ( Types I, and II). The measurements of the three Individual determinations of the sample unit for spray rating for the types I, and II cloths shall be equal to or better th
20、an 80, 80, 70 when tested in accordance with AATCC 22 Water Repellency: Spray Test. 3.6 Type II water repellant and mildew after treated cloth. 3.6.1 Water repellent and mildew resistant after treated. The cloth shall have a commercial acceptable water repellant finish and shall meet the requirement
21、s as specified in 3.5.1, 3.5.1.1 and 3.5.1.2. 3.6.2 Mildew resistant. Textile materials intended for direct contact with soil, such as, but not limited to CCC-C-419, CCC-C-428, MIL-C-10799, MIL-C-10859, MIL-C-43627, MIL-T-3530, MIL-T-43566, MIL-W-43638, MIL-W-530, MIL-W-5665, shall be treated with a
22、n inorganic, metalized, mildew inhibitor. A certificate of compliance will be accepted which certifies that the textile material shall retain a 75% breaking strength after 12 weeks soil burial initially and after leaching when tested in accordance with AATCC Test Method 30, Antifungal Activity, Asse
23、ssment of Textile Materials: Mildew and Rot Resistance of Textile Materials, Test 1. Textile materials intended for use that will not come into contact with soil, such as, but not limited to CCC-C-429, CCC-C-700, MIL-B-371, MIL-F-2312, may be treated with an organic mildew inhibitor. A certificate o
24、f compliance will be accepted which certifies the textile material has been tested in accordance with AATCC Test Method 30, Test III and rated no more than “Microscopic Growth”. 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 3.6.3 Colorfa
25、stness of Type II The colorfastness of the cloth prior to after treatment shall be as specified in 3.4.2 3.7 Type III mildew-resistant after treated. 3.7.1 Type III cloth. The cloth shall be mildew - resistant treated in accordance with 3.6.2. 3.7.2 Colorfastness of Type III cloth. The colorfastness
26、 requirements for the cloth shall be as specified for the type II cloth as in 3.6.3. 3.8. pH. All types I and II treated cloths shall have a pH value not less than 5.5 nor more than 8.5 when tested in accordance with AATCC 81 pH of the Water Extracted from Textiles. 3.9 Fiber identification. Each ro
27、ll shall be labeled, and ticketed for fiber content in accordance with the Rules and Regulations Under the Textile Fiber Products Identification Act. 3.10 Marking. The face side of the cloth shall be identified by applying a stamping on that side of the cloth with the word “Face” at each end of the
28、roll. 3.11 Length and put-up. The put-up shall be commercial. The minimum length of pieces shall be as specified in accordance with the untreated cloth specification. 3.12 Workmanship. The finished cloth shall conform to the quality established by this specification. 3.13 Toxicity. The finished clot
29、h shall not present a dermal health hazard when used as intended. Before use, mildew inhibitors must have written toxicity approval from U.S. Army Center for Health Promotion and Preventive Medicine, 5158 Blackhawk Rd., Aberdeen Proving Ground, Maryland 21010-5403. 4. REGULATORY REQUIREMENTS. 4.1 Re
30、cycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible in accordance with paragraph 23.403 of the Federal Acquisition Regulation Act (FAR), provided that the material meets or exceeds the
31、operational and maintenance requirements and promotes economically advantageous life cycle costs. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description and conform to the producers own drawings, speci
32、fications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance. 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 5.2 Visual examination. Each roll in the sample shall be examined
33、 on the face side only. When the total yardage in the roll does not exceed 100 yards, the entire yardage in the roll shall be examined. When the total yardage in the roll exceeds 100 yards, only 100 yards shall be-examined for the defects listed below. 5.2.1 Defects. Any hole, cut, or tear; broken o
34、r missing yarn; smash; float, mispick, harness skip, or other misweave; hitchback, stripback; open or thin place, crack (warp or filling); knot or slub; loose, slack, or tight yarns; reed mark, wrong draw; abrasion mark, bruise, tender or weak spot; embedded crease or wrinkle; selvage cut, torn, fol
35、ded, rolled, slack, or tight; filling bar, coarse filling, or mixed filling; spot, stain, streak, or dirty yarn; foreign matter; shade not as specified; finish not equal to or better than standard; offshade or uneven shading throughout piece; mottled, cloudy, streaky, or barre; overall uncleanness o
36、r soiled; baggy, ridgy, wavy, or unevenly woven; width not within established tolerances; net length less than indicated on the ticket; fiber identification marking omitted; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on
37、 roll; bar code causes damage to the item; any items not packaged in accordance with the contract or purchase order. Each defect shall be marked with a 1-1/2 inch long string; the string shall be inserted into the selvage opposite the defect. 5.3 Acceptance criteria. Acceptance criteria shall be as
38、specified in the contract or purchase order. 6. PACKAGING. The preservation, Packaging and marking shall be as specified in the contract or order. 7. NOTES7.1 Source of Government documents. Copies of military and federal documents are available from: Standardization Documents Order Desk Bldg. 4D 70
39、0 Robbins Avenue Philadelphia, PA 19111-5094 7.1.1 Other Government Documents FEDERAL TRADE COMMISSION Rules and Regulations Under The Textile Fiber Products Identification Act (Copies may be obtained without charge from the Federal Trade Commission, Washington, DC 20580-0001). 6Provided by IHSNot f
40、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 CODE OF FEDERAL REGULATIONS 16 CFR Part 1500 - Federal Hazardous Substances Act Regulations 29 CFR Part 1910 - Occupational Safety and Health Standards (Applications for copies of referenced documents should be a
41、ddressed to U. S. Government Printing Office, Superintendent of Documents, Mail Stop: SSOP, Washington, DC 20402-9328.) CODE OF FEDERAL REGULATIONS Title 40, part 798.4470 (Primary Dermal Irritation) (This reference may be found on the Internet at www.access.gpo.gov/nara/cfr/cfr-table-search.html.)
42、7.2 Source of non-Government documents. American Society for Testing and Materials (ASTM) Test Methods (Applications for copies should be addressed to American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken PA, 19428-2959) American Association of Textile Chemists and Colo
43、rists (AATCC) Test Methods (Application for copies should be addressed to the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709.) Principles and Methods of Toxicology, A. Wallace Hayes (editor), 1989, pp 394-396. (Applications for copies of refe
44、renced documents should be addressed to Raven Press, 1185 Avenue of the Americas, New York, NY 10036) 7.3 Titles of non-Government Documents. ASTM-D-3775 Standard Test Method for Fiber Count of Woven Fabric. ASTM-D-5034 Standard Test method for Breaking Strength and Elongation of textile methods. AS
45、TM-D-96 Shrinkage in Laundering: Cotton Linen AATCC Crockmeter Method 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59708 AATCC 127 Water Resistance: Hydrostatic Pressure Test. AATCC 22 Water Repellency: Spray Test AATCC 30 Antifungal Activity
46、, Assessment on Textile Materials: Mildew and Rot Resistance of Textile Materials AATCC 81 pH of the Water Extracted from Textiles 7.4 Sources for Cotton Cloth. For cotton cloth sources see the individual end item specifications. 7.5 Sources of Mildew Inhibitor. Sources that could be used but not li
47、mited to, are as follows: a. Rohm and Hass Company 100 Independence Mall West Philadelphia, PA 19106-2899 b. Kenney Sales Associates P.O. Box 258 89 Main St. Medway, MA 02053”. MILITARY INTRESTS: CIVIL AGENCY COORDINATING ACTIVITIES: Custodians GSA-FSS Army-GL JUS-FPI Navy-NU PREPARING ACTIVITY: Review Activity DSCP-CT Army-MD, AV Navy-MC, YD (Project Number 8305-0797) 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
