1、AMSC N/A FSC 5905 INCH-POUND A-A-59769/1A 22 January 2013 SUPERSEDING A-A-59769/1 15 April 2005 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET RESISTOR NETWORKS, BALL GRID ARRAY TERMINATORS THEVENIN TERMINATION The General Services Administration has authorized the use of this commercial item descr
2、iption (CID) for all agencies. The complete requirements for procuring the 8 bit thevenin termination which provides high performance termination and backplanes, and eliminates parasitic capacitance and inductance is described herein and shall consist of this document and the issue in effect of CID
3、A-A-59769. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) uses a classification system that is included in the PIN as shown in the following example (see NOTES). AA59769 01 -001 CID number Applicable CID specification sheet(two digits) Dash number (see tab
4、le I) SALIENT CHARACTERISTICS Interface and physical dimensions. The resistor networks supplied to this CID specification sheet shall meet the interface and physical dimensions as specified herein (see figure 1). Schematic diagram. The schematic diagram shall be as specified in figure 2. Maximum res
5、istor power. The maximum resistor power shall be 0.05 watts at 70OC. Maximum package power. The maximum package power shall be 1.0 watt at 70OC. Resistance. The resistance shall be as specified in table I. Resistance tolerance. The resistance tolerance shall be 1.0 percent. Temperature coefficient o
6、f resistance (TCR). The temperature coefficient of resistance (TCR) shall be 200 ppm/OC. Operating ambient temperature. The operating ambient temperature range shall be -55OC to +125OC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59769/1A 2 M
7、arking. Resistors supplied to this CID specification sheet shall be marked with the manufacturers standard commercial PIN. L W H P Inch 0.315 0.006 0.118 0.006 0.047 0.006 0.039 0.010 mm 8.00 0.15 3.00 0.15 1.19 0.15 1.00 0.25 D K Co-planarity Inch 0.025 0.002 0.020 0.010 0.006 mm 0.64 0.05 0.50 0.2
8、5 0.15FIGURE 1. Case dimensions and configuration. FIGURE 2. Schematic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59769/1A 3 TABLE I. Rating and characteristics. CID dash number R1(ohms) R2 (ohms) Array size Pitch -001 330 470 3 x 8
9、 0.039 (1.00 mm) -002 220 1,800 3 x 8 0.039 (1.00 mm) NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See classification information for PIN format example. Source of documents. Commercial Item Description A-A-59769 - Resistor Ne
10、tworks, Ball Grid Array Terminators, General Requirements for. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the DLA Document Services Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) Ordering data. Ordering data is as specifi
11、ed in A-A-59769. Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the
12、requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown). TABLE II. Commercial products. MFRs CAGE MFRs name and address 11236 CTS Corporation Berne Division 406 Parr Road Berne,
13、 IN 46711-9505 Phone: (574) 293-7511 Website: http:/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59769/1A 4 Part number (P/N) supersession data. This CID supersedes the following MFRs P/Ns as shown. This information is being provided to assis
14、t in reducing proliferation in the Government inventory system. TABLE III. P/N supersession data. CID dash number AA5976901- MFRs P/N 1/ MFRs CAGE 001 RT1210B7 11236 002 RT1211B71/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the tim
15、e of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph of A-A-59769. Changes from previous issue. The margins of this CID are marked with vertic
16、al lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entir
17、e content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FAS Navy - EC DLA - CC Preparing Activity: DLA - CC Project 5905-2010-027 NOTE: The activities listed above were interested in this
18、document as the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
