1、INCHPOUND AA59789/21 21 October 2011 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .260 INCH BODY SIZE, WITH TWO OR NO MOUNTING HOLES, SCREW ACTUATED The General Services Administration has authorized the use of
2、 this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CI
3、D) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59789 CID number /21 Applicable CID sheet * Configuration (see table I) * Finish * * Length (see table II) * Mounting (see table I) Ex
4、ample: AA59789/21WR55S is the PIN for a clear chemical film finished, 5.3 inch (134.6 mm) long card holder. The card holder also features two tapped mounting holes for use with 256 UNC 2B fasteners and a lockwasher and flat washer under the screw head for added resistance to loosening. SALIENT CHARA
5、CTERISTICS. Performance. Card holders shall hold the circuit card firmly in its installed position and prevent loosening or movement as a result of shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly to the cold plate. Interface and physical dimensions.
6、The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension
7、for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “N“, “S“, “R“, “P“, and “T“. Cold plate slot width. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed boar
8、d of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is as follows: 6 inch-pounds (68 N-cm) for assemblies of configuration “A“, “C“, “F“, or “W“ and 7.2 inch-pounds (81 N-cm) for assemblies of configurations “D“, “J“, “L“, or “N“. Configurat
9、ion. The configuration of a card holder shall be as specified in table I. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 or 4. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
10、m IHS-,-,-AA59789/21 2 TABLE I. Configuration. Configuration Mounting body style (see figure 2) Mounting options Applicable figures Hardware options A A P, S, R, T 1 and 2 No hardware options added C C N, S, R, T F A P, S, R, T 1, 2, and 3 Lockwasher and flat washer W C N, S, R, T N A P, S, R, T 1,
11、2, and 4 Screw self-lock element L C N, S, R, T J A P, S, R, T 1, 2, 3, and 4 Lockwasher, flat washer, and screw self-lock element D C N, S, R, T Inches mm Inches mm Inches mm .125 .140 3.18 3.56 .225 .270 5.72 6.86 .30 .900 7.6 22.86 FIGURE 1. Relaxed and expanded dimensions (two mounting hole vers
12、ion shown). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/21 3 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals a
13、nd .010 inch (0.25 mm) for three place decimals. 3. Screw and alignment spring not shown. See table II and figure 2 for hole spacing requirements. 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm). 5. Mounting body style “A“ is capable of safely expanding to .330 inch (
14、8.38 mm) and mounting body style “C“ is capable of expanding to .325 inch (8.26 mm) minimum. 6. Maximum screw advance is .12 inch (3.0 mm) for mounting body style “A“ and .14 inch (3.6 mm) for mounting body style “C“. FIGURE 1. Relaxed and expanded dimensions Continued. Finish. The finish designator
15、 shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film). Length, expanded and relaxed dimensions. The length designator s
16、hall be as specified in AA59789. The lengths available for this CID specification sheet are listed in table II. The length, expanded and relaxed dimensions shall be as specified on figure 1. TABLE II. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “L“ .02 (0.5) Mounting body
17、style Dimension “A“ .01 (0.3) Dimension “B“ .02 (0.5) Dimension “M“ 2/ 50 4.8 (121.9) A 1.50 (38.1) .30 (7.6) .900 C 1.60 (40.6) .35 (8.9) .900 55 5.3 (134.6) A 2.00 (50.8) .55 (14.0) .900 C 1.60 (40.6) .35 (8.9) .900 60 5.8 (147.3) A 2.50 (63.5) .80 (20.3) .900 C 1.60 (40.6) .35 (8.9) .900 65 6.3 (
18、160.0) A 3.00 (71.2) 1.05 (26.7) .900 C 1.60 (40.6) .35 (8.9) .900 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. 2/ Tolerance for the hole spacing is .005 inch (0.51 mm). Mounting body style (see figure 2 and table II). Two mounting body styles are
19、 available on this CID specification sheet, style A or style C. The primary difference in the two mounting body styles are the location of mounting holes on the mounting body as depicted on figure 2. Mounting body style A always has two locations for fasteners or indexing pins centered on the mounti
20、ng body that are .900 inch (22.86 mm) apart. Mounting body style C can have two holes or no holes on the mounting body. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/21 4 Inches mm .040 .062 1.02 1.57 NOTES: 1. Dimensions are in inches. Mil
21、limeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. See table II for dimensions B and M. FIGURE 2. Mounting body style details. Mounting. The mounting designators
22、 shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “N“ (no mounting holes; mounting body style C only), “P“ (.062 x .040 index pins; mounting body style A only), “R“ (rivet mount holes with counterbore and countersink), “S“ (tapped 256
23、holes), or “T“ (tapped 080 holes). See figure 1 for mounting hole spacing requirements. Card holders using mounting option “P“ and “R“ may be shipped unassembled. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/21 5 Rivet mount holes. The hol
24、es used for rivet mounting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with a counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet style A as specified in AA59789 when r
25、ivet mounting is used. Configuration hardware options. Card holders can have the following hardware options. See table I for the correct PIN configuration identifier. Lockwasher and flat washer (see figure 3). A lockwasher and flat washer located under the screw head will provide for additional resi
26、stance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include configuration identifier “F“ or “W“ in the PIN (see classification and notes section herein). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The u
27、se of a screw self-locking element will provide prevailing torque for resistance to loosening of the assembly from shock vibration. The screw self-locking element shall be in accordance with AA59789. Card holders requiring a screw self-locking element shall include configuration identifier “L“ or “N
28、“ in the PIN (see classification and notes section herein). FIGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include configuration identifier “D“ or “J“
29、 in the PIN (see classification and notes section herein). NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitte
30、d without license from IHS-,-,-AA59789/21 6 Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or
31、 https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet w
32、as coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not
33、 be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 T
34、elephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 URL: 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 Card Locks Unlimited, Inc.
35、2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersede the following manufacturers part numbers in table III and on DESC Drawing 89064 (table IV) as shown. The CID
36、PINs listed in table III are only for length designator “50“. See tables V and VI for CID PIN construction using other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for
37、 ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/21 7 TABLE III. Commercial part number supersession data. PIN designator AA59789/21 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/21 Vendor similar designator or type part number
38、1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 AB50S 40510B CB50S A226CR4.80T2 5226BA4.80T2 AB50R 40510BR CB50R A226CR4.80H 5226BA4.80H AB50T 40510BT CB50T A226CR4.80T0 5226BA4.80T0 AB50P 40510BP CB50N A226CR4.80 5226BA4.80 FB50S 40510BLF WB50S WA226CR4.80T2 5226WBA4.80T2
39、FB50R 40510BLFR WB50R WA226CR4.80H 5226WBA4.80H FB50T 40510BLFT WB50T WA226CR4.80T0 5226WBA4.80T0 FB50P 40510BLFP WB50N WA226CR4.80 5226WBA4.80 NB50S 40510BL LB50S A226CR4.80T2L 5226BA4.80T2L NB50R 40510BRL LB50R A226CR4.80HL 5226BA4.80HL NB50T 40510BTL LB50T A226CR4.80T0L 5226BA4.80T0L NB50P 40510B
40、PL LB50N A226CR4.80L 5226BA4.80L JB50S 40510BLFL DB50S WA226CR4.80T2L 5226WBA4.80T2L JB50R 40510BLFRL DB50R WA226CR4.80HL 5226WBA4.80HL JB50T 40510BLFTL DB50T WA226CR4.80T0L 5226WBA4.80T0L JB50P 40510BLFPL DB50N WA226CR4.80L 5226WBA4.80L AC50S 40510 CC50S 226CR4.80T2 5226CG4.80T2 AC50R 40510R CC50R
41、226CR4.80H 5226CG4.80H AC50T 40510T CC50T 226CR4.80T0 5226CG4.80T0 AC50P 40510P CC50N 226CR4.80 5226CG4.80 FC50S 40510LF WC50S W226CR4.80T2 5226WCG4.80T2 FC50R 40510LFR WC50R W226CR4.80H 5226WCG4.80H FC50T 40510LFT WC50T W226CR4.80T0 5226WCG4.80T0 FC50P 40510LFP WC50N W226CR4.80 5226WCG4.80 NC50S 40
42、510L LC50S 226CR4.80T2L 5226CG4.80T2L NC50R 40510RL LC50R 226CR4.80HL 5226CG4.80HL NC50T 40510TL LC50T 226CR4.80T0L 5226CG4.80T0L NC50P 40510PL LC50N 226CR4.80L 5226CG4.80L JC50S 40510LFL DC50S W226CR4.80T2L 5226WCG4.80T2L JC50R 40510LFRL DC50R W226CR4.80HL 5226WCG4.80HL JC50T 40510LFTL DC50T W226CR
43、4.80T0L 5226WCG4.80T0L JC50P 40510LFPL DC50N W226CR4.80L 5226WCG4.80L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/21 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/21
44、Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/21 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 AP50S 40510N CE50S EN226CR4.80T2 5226EN4.80T2 AP50R 40510NR CE50R EN226CR4.80H 5226EN4.80H AP5
45、0T 40510NT CE50T EN226CR4.80T0 5226EN4.80T0 AP50P 40510NP CE50N EN226CR4.80 5226EN4.80 FP50S 40510NLF WE50S WEN226CR4.80T2 5226WEN4.80T2 FP50R 40510NLFR WE50R WEN226CR4.80H 5226WEN4.80H FP50T 40510NLFT WE50T WEN226CR4.80T0 5226WEN4.80T0 FP50P 40510NLFP WE50N WEN226CR4.80 5226WEN4.80 NP50S 40510NL LE
46、50S EN226CR4.80T2L 5226EN4.80T2L NP50R 40510NRL LE50R EN226CR4.80HL 5226EN4.80HL NP50T 40510NTL LE50T EN226CR4.80T0L 5226EN4.80T0L NP50P 40510NPL LE50N EN226CR4.80L 5226EN4.80L JP50S 40510NLFL DE50S WEN226CR4.80T2L 5226WEN4.80T2L JP50R 40510NLFRL DE50R WEN226CR4.80HL 5226WEN4.80HL JP50T 40510NLFTL D
47、E50T WEN226CR4.80T0L 5226WEN4.80T0L JP50P 40510NLFPL DE50N WEN226CR4.80L 5226WEN4.80L AH50S 40510B3 CH50S HA226CR4.80T2 5226BH4.80T2 AH50R 40510B3R CH50R HA226CR4.80H 5226BH4.80H AH50T 40510B3T CH50T HA226CR4.80T0 5226BH4.80T0 AH50P 40510B3P CH50N HA226CR4.80 5226BH4.80 FH50S 40510B3LF WH50S WHA226CR4.80T2 5226WBH4.80T2 FH50R 40510B3LFR WH50R WHA226CR4.80H 5226WBH4.80H FH50T 40510B3LFT WH50T WHA226CR4.80T0 5226WBH4.80T0 FH50P 4
