1、INCH-POUND AA59789/3A 21 July 2010 SUPERSEDING AA59789/3 26 March 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .225 X .225 INCH BODY SIZE, WITH TWO MOUNTING HOLES, WITH SCREW ACTUATION AND RETENTION The General S
2、ervices Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NU
3、MBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see NOTES). AA59789 CID number /03 Applicable CID sheet * Configuration (see table I) * Finish (see table I
4、) * * Length (see table II) * Mounting (see table I) Example: AA59789/03NH60T is the PIN for a hard black anodize finished, 5.8 inch (147.3 mm) long card holder with a retained actuating screw. The card holder also feature two tapped mounting holes for use with 080 UNF 2B fasteners and a lockwasher
5、and flat washer under the screw head for added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card firmly in place providing high resistance to shock and vibration while providing maximum thermal transfer. Interface and physical dimensions. The car
6、d holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. Card holders shall have a screw retention feature to prevent unintentional disassembly of the card holder. Material. Unless otherwise specified herein, the card
7、 holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “S“, “R“, “P“, “U“, and “T“. Cold plate slot width. The recommend cold plate slot width to accommodate the circuit c
8、ard assembly with attached card holder is .250 inch (6.35 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is as follows: 6 inch-pounds (0.68 N-m) for assemblies of configuration “A“, “C“, “F“, or
9、 “W“ and 7.2 inch-pounds (0.81 N-m) for assemblies of configurations “D“, “J“, “L“, or “N“. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/3A 2 Configuration. The configuration of a card holder shall be as specified in tabl
10、e I. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. TABLE I. Configurations. Configuration Mounting body style Finish options Mounting options Applicable figures Hardware options A A B, C, H, P S, R, T, P 1 and 2 No hardware o
11、ptions added C C B, C, E, H S, R, T, U F A B, C, H, P S, R, T, P 1, 2, and 3 Lockwasher and flat washer W C B, C, E, H S, R, T, U N A B, C, H, P S, R, T, P 1, 2, and 4 Screw self-lock element L C B, C, E, H S, R, T, U J A B, C, H, P S, R, T, P 1, 2, 3, and 4 Lockwasher, flat washer, and screw self-l
12、ock element D C B, C, E, H S, R, T, U Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “P“ (electrodeposited nickel), or “H“ (hard black ano
13、dize). The center mounting wedge is not finished for card holders using mounting option “P“. Length, expanded and relaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and re
14、laxed dimensions shall be as specified on figure 1. TABLE II. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “L“ .02 (0.5) Mounting body style Dimension “A“ .01 (0.3) Dimension “B“ .02 (0.5) Dimension “C“ Minimum 50 4.8 (121.9) A 1.50 (38.1) .30 (7.6) .275 (6.99) C
15、 1.50 (38.1) .30 (7.6) .275 (6.99) 55 5.3 (134.6) A 2.00 (50.8) .55 (14.0) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99) 60 5.8 (147.3) A 2.50 (63.5) .80 (20.3) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99) 65 6.3 (160.0) A 3.00 (71.2) 1.05 (26.7) .275 (6.99) C 1.50 (38.1) .30 (7.6) .275 (6.99)
16、1/ Dimensions are in inches. Millimeters are given for information only. Mounting. The mounting designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “S“ (tapped 2-56 holes), “R“ (rivet mount holes with counterbore and countersi
17、nk), “T“ (tapped 0-80 holes), “P“ (.062 x .040 index pins), or “U“ (tapped metric M2 x 0.4 holes). See figure 1 for mounting hole spacing requirements. Card holders using mounting option “P“ and “R“ may be shipped unassembled. The center mounting wedge is not finished for card holders using mounting
18、 option “P“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/3A 3 Rivet mounting holes. The holes used for rivet mounting shall be .066/.073 inch (1.68/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes w
19、ith a counterbore of .156 inch (3.96 mm) diameter with a depth of .165 inch (4.19 mm) for style C mounting bodies and .175 inch (4.45 mm) for style A mounting bodies. Rivets. This card holder uses rivet type A as specified in AA59789 when rivet mounting is used. Inches mm Inches mm Inches mm .125 .1
20、40 3.18 3.56 .225 .235 5.72 5.97 .30 .900 7.6 22.86 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 (0.25 mm) for three place decimals. 3. The across fl
21、ats dimension for hex drive socket shall be .094 inch (2.38 mm). 4. Tolerance for the hole spacing is .010 inch (0.25 mm) for mounting body style A and .005 inch (0.51 mm) for mounting body style C. FIGURE 1. Relaxed and expanded dimensions. Provided by IHSNot for ResaleNo reproduction or networking
22、 permitted without license from IHS-,-,-AA59789/3A 4 Screw retention locknut (see figure 2). Card holders shall have a screw retention locknut intended to prevent unintentional disassembly of the card holder. The locknut shall be fabricated of a corrosion resistant material. FIGURE 2. Screw retainin
23、g self-locking nut (corrosion resistant) details. Hardware options. Card holders can have the following options: no hardware options added, lockwasher and flat washer (see figure 3), screw self lock element (see figure 4), or lockwasher, flat washer, and screw self lock element (see figures 3 and 4)
24、. See table I for the correct PIN configuration identifier. No hardware options added. The base configuration of the card holder is as depicted by figures 1 and 2 . Card holders not requiring any hardware options shall include configuration identifier “A“ or “C“ in the PIN (see classification, notes
25、, and table I). Lockwasher and flat washer (see figure 3). A lockwasher and flat washer located under the screw head will provide for additional resistance to loosening from shock and vibration. Card holders requiring a lockwasher and flat washer shall include configuration identifier “F“ or “W“ in
26、the PIN (see classification, notes, and table I). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock vibration. Card holders requiring a screw self-lock
27、ing element shall include configuration identifier “L“ or “N“ in the PIN (see classification, notes, and table I). FIGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element o
28、ption shall include configuration identifier “D“ or “J“ in the PIN (see classification, notes, and table I). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/3A 5 NOTES. PIN. The PIN should be used for Government purposes to buy commercial pro
29、ducts to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available on
30、line at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59789. Commercial products. As part of the market analysis a
31、nd research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID speci
32、fication sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Electronic P
33、ackaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 6794555 (URL): 52094 Calmark A Division of Pentair Electronic Packaging 7238 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858)
34、7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as
35、shown in table III. The CID PINs listed in table III are only for length designator “60”. See table IV for CID PIN construction using other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. P
36、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/3A 6 TABLE III. Commercial part number supersession data. PIN designator AA59789/03 Vendor similar designator or type part number 1/ CAGE 18915 PIN designator AA59789/03 Vendor similar designator
37、 or type part number 1/ CAGE 52094 Vendor similar designator or type part number 1/ CAGE 5BG68 AB60S 42512BLN CB60S A231CR5.80T2R 5231BA5.80T2R AB60R 42512BLNR CB60R A231CR5.80HR 5231BA5.80HR AB60T 42512BLNT CB60T A231CR5.80T0R 5231BA5.80T0R AB60P 42512BLNP CB60U A231CR5.80TM2R 5231BA5.80TM2R FB60S
38、42512BLFLN WB60S WA231CR5.80T2R 5231WBA5.80T2R FB60R 42512BLFLNR WB60R WA231CR5.80HR 5231WBA5.80HR FB60T 42512BLFLNT WB60T WA231CR5.80T0R 5231WBA5.80T0R FB60P 42512BLFLNP WB60U WA231CR5.80TM2R 5231WBA5.80TM2R NB60S 42512BLNL LB60S A231CR5.80T2LR 5231BA5.80T2LR NB60R 42512BLNRL LB60R A231CR5.80HLR 52
39、31BA5.80HLR NB60T 42512BLNTL LB60T A231CR5.80T0LR 5231BA5.80T0LR NB60P 42512BLNPL LB60U A231CR5.80TM2LR 5231BA5.80TM2LR JB60S 42512BLFLNL DB60S WA231CR5.80T2LR 5231WBA5.80T2LR JB60R 42512BLFLNR DB60R WA231CR5.80HLR 5231WBA5.80HLR JB60T 42512BLFLNTL DB60T WA231CR5.80T0LR 5231WBA5.80T0LR JB60P 42512BL
40、FLNPL DB60U WA231CR5.80TM2LR 5231WBA5.80TM2LR AC60S 42512LN CC60R 231CR5.80T2R 5231CG5.80T2R AC60R 42512LNR CC60S 231CR5.80HR 5231CG5.80HR AC60T 42512LNT CC60T 231CR5.80T0R 5231CG5.80T0R AC60P 42512LNP CC60U 231CR5.80TM2R 5231CG5.80TM2R FC60S 42512LFLN WC60S W231CR5.80T2R 5231WCG5.80T2R FC60R 42512L
41、FLNR WC60R W231CR5.80HR 5231WCG5.80HR FC60T 42512LFLNT WC60T W231CR5.80T0R 5231WCG5.80T0R FC60P 42512LFLNP WC60U W231CR5.80TM2R 5231WCG5.80TM2R NC60S 42512LNL LC60S 231CR5.80T2LR 5231CG5.80T2LR NC60R 42512LNRL LC60R 231CR5.80HLR 5231CG5.80HLR NC60T 42512LNTL LC60T 231CR5.80T0LR 5231CG5.80T0LR NC60P
42、42512LNPL LC60U 231CR5.80TM2.5LR 5231CG5.80TM2LR See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/3A 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/03 Vendor similar design
43、ator or type part number 1/ CAGE 18915 PIN designator AA59789/03 Vendor similar designator or type part number 1/ CAGE 52094 Vendor similar designator or type part number 1/ CAGE 5BG68 JC60S 42512LFLNL DC60S W231CR5.80T2LR 5231WCG5.80T2LR JC60R 42512LFLNRL DC60R W231CR5.80HLR 5231WCG5.80HLR JC60T 42
44、512LFLNTL DC60T W231CR5.80T0LR 5231WCG5.80T0LR JC60P 42512LFLNPL DC60U W231CR5.80TM2.5LR 5231WCG5.80TM2LR AP60S 42512NLN CE60S EN231CR5.80T2R 5231EN5.80T2R AP60R 42512NLNR CE60R EN231CR5.80HR 5231EN5.80HR AP60T 42512NLNT CE60T EN231CR5.80T0R 5231EN5.80T0R AP60P 42512NLNP CE60U EN231CR5.80TM2R 5231EN
45、5.80TM2R FP60S 42512NLFLN WE60S WEN231CR5.80T2R 5231WEN5.80T2R FP60R 42512NLFLNR WE60R WEN231CR5.80HR 5231WEN5.80HR FP60T 42512NLFLNT WE60T WEN231CR5.80T0R 5231WEN5.80T0R FP60P 42512NLFLNP WE60U WEN231CR5.80TM2R 5231WEN5.80TM2R NP60S 42512NLNL LE60S EN231CR5.80T2LR 5231EN5.80T2LR NP60R 42512NLNRL LE
46、60R EN231CR5.80HLR 5231EN5.80HLR NP60T 42512NLNTL LE60T EN231CR5.80T0LR 5231EN5.80T0LR NP60P 42512NLNPL LE60U EN231CR5.80TM2LR 5231EN5.80TM2LR JP60S 42512NLFLNL DH60S WEN231CR5.80T2LR 5231WEN5.80T2LR JP60R 42512NLFLNRL DH60R WEN231CR5.80HLR 5231WEN5.80HLR JP60T 42512NLFLNTL DH60T WEN231CR5.80T0LR 52
47、31WEN5.80T0LR JP60P 42512NLFLNPL DH60U WEN231CR5.80TM2LR 5231WEN5.80TM2LR AH60S 42512B3LN CH60S HA231CR5.80T2R 5231BH5.80T2R AH60R 42512B3LNR CH60R HA231CR5.80HR 5231BH5.80HR AH60T 42512B3LNT CH60T HA231CR5.80T0R 5213BH5.80T0R AH60P 42512B3LNP CH60U HA231CR5.80TM2R 5231BH5.80TM2R FH60S 42512B3LFLN WH60S WHA231CR5.80T2R 5231WBH5.80T2R FH60R 42512B3LFLNR WH60R WHA231CR5.80HR 5231WBH5.80HR FH60T 42512B3LFLNT WH60T WHA231CR5.80T0R 5231WBH5.80T0R FH60P 42512B3LFLNP WH60U WHA231CR5.80TM2R 5231WB
