1、INCHPOUND AA59832/6 6 March 2011 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET EXTRACTOR, ELECTRICAL CARD, METAL, NONLOCKING, SINGLESIDED ACTUATION, NARROW PROFILE, STRAIGHT ACTUATING HANDLE FOR .032, .063, .094, .125, AND .156 INCH THICK CIRCUIT CARD ASSEMBLIES The General Services Administration
2、 has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring extractors described herein shall consist of this document and the latest issue in effect of AA59832. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item de
3、scription (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see NOTES herein). AA59832 CID number /06 Applicable CID sheet * Configuration (see table I) * Slot width (see table II) * Material * Finish *
4、 Color (see table III) Example: AA59832/06S21AB is the PIN for a right side straight handle aluminum extractor designed for mounting on a circuit card assembly with a printed board thickness of .063 inch (1.60 mm) in width. The corrosion protection finish applied to the extractor is black hard anodi
5、ze and the handle has a sensitive electronic device (SED) symbol. SALIENT CHARACTERISTICS. Performance. Extractors shall be capable of initiating the removal of a circuit card assembly from its installed position. The mechanical advantage of all extractor configurations on this CID specification she
6、et is approximately 4.2:1. Interface and physical dimensions. The extractors supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59832. Configuration. The configuration of an extractor shall be as specified in table I and on figu
7、res 1 through 6. TABLE I. Configurations. Configuration Applicable figures Extractor description K 1 and 2 Left hand with SED symbol on the straight handle L 1 Left hand with straight handle M 3 Left hand with bent leg and straight handle N 3 and 4 Left hand with bent leg and SED symbol on the strai
8、ght handle P 4 and 5 Right hand with bent leg and SED symbol on the straight handle Q 5 Right hand with bent leg and straight handle R 6 Right hand with straight handle S 6 and 2 Right hand with SED symbol on the straight handle AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or netwo
9、rking permitted without license from IHS-,-,-AA59832/6 2 Slot width. The available slot widths needed to accommodate various printed board thicknesses for the extractors covered by this CID specification sheet are specified in table II. The slot width designator shall be included in the PIN. TABLE I
10、I. Slot width configurations and dimensions. 1/ Slot width designator Slot width dimension “A“ 2/ Inch (mm) Accommodates printed board thickness Inch (mm) Roll pin width Inch (mm) Handle width dimension “B“ Inch (mm) 1 .040 (1.02) .032 (0.8) .187 (4.75) .25 (6.4) 2 .075 (2.03) .063 (1.6) .187 (4.75)
11、 3 .105 (2.79) .094 (2.4) .250 (6.35) 4 .142 (3.56) .125 (3.2) .250 (6.35) .29 (7.4) 5 .165 (4.19) .156 (4.0) .312 (7.94) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. 2/ Tolerance is +.010, .000 inch (+0.25, 0.000 mm). Material. The material used
12、in the extractor body shall be as specified in AA59832. The applicable material type designators for this CID specification sheet are “1“ (aluminum alloy 6061, temper T6), “2“ (aluminum alloy 5052, temper H32), or “7“ (Stainless steel, type 301 or 304). The material designator shall be included in t
13、he PIN. Material thickness. The aluminum or stainless steel thickness shall be .063 .002 inch (0.23 0.05 mm). Roll pin. A stainless steel roll pin is furnished with each extractor. The roll pin is .09375 inch (2.38 mm) diameter by the lengths specified in table II. Finish. The finish designator shal
14、l be as specified in AA59832. The finishes available for this CID specification sheet are as follows: “A“ (anodize) or “L“ (low resistance chemical film) for extractors fabricated of aluminum alloys and “P“ (passivation treatment) extractors fabricated of stainless steel. Color. The color designator
15、 shall be as specified in AA59832. The colors available for this CID specification sheet shall be “C“ (clear) or “G“ (gold) for low resistance chemical film and “C“ (clear) for passivation treatment. The color of anodized extractors shall be specified in table III. The color designator shall be incl
16、uded in the PIN. TABLE III. Colors of anodized extractors. Designator Color Designator Color B Black R Red C Clear U Blue D Green V Violet (purple) E Gray W Brown F Orange Y Yellow Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 3 Inches mm
17、 Inches mm Inches mm Inches mm Inches mm .003 .005 0.08 0.13 .020 .090 0.51 2.29 .093 .125 2.36 3.18 .140 .18 3.56 4.57 .360 1.00 1.50 9.14 25.4 38.1 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 i
18、nch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Depth dimension is .29 inch (7.4 mm) for extractors from CAGE 18915 and 5GB68 and .27 inch (6.9 mm) from CAGE 61081. FIGURE 1. Configuration L dimensions (left hand). Provided by IHSNot for ResaleNo reproductio
19、n or networking permitted without license from IHS-,-,-AA59832/6 4 NOTES: 1. The SED symbol displayed on the extractor handles shall be in accordance with AA59832. 2. Unless otherwise specified, a monochromatic reproduction of the symbol displayed in AA59832 using any color that contrasts with the c
20、olor of the extractor handle may be used. FIGURE 2. Configurations K and S with SED symbol on extractor handle (board edge view). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 5 Inches mm Inches mm Inches mm Inches mm Inches mm .003 .005
21、0.08 0.13 .020 .035 0.51 0.89 .090 .093 2.29 2.36 .125 .140 3.18 3.56 .360 1.00 1.50 9.14 25.4 38.1 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch
22、 (0.25 mm) for three place decimals. 3. Depth dimension is .29 inch (7.4 mm) for extractors from CAGE 18915 and 5GB68 and .27 inch (6.9 mm) from CAGE 61081. FIGURE 3. Configuration M dimensions (left hand with bent leg). Provided by IHSNot for ResaleNo reproduction or networking permitted without li
23、cense from IHS-,-,-AA59832/6 6 NOTES: 1. The SED symbol displayed on the extractor handles shall be in accordance with AA59832. 2. Unless otherwise specified, a monochromatic reproduction of the symbol displayed in AA59832 using any color that contrasts with the color of the extractor handle may be
24、used. FIGURE 4. Configurations N and P with SED symbol on extractor handle (board edge view). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 7 Inches mm Inches mm Inches mm Inches mm Inches mm .003 .005 0.08 0.13 .020 .035 0.51 0.89 .090 .
25、093 2.29 2.36 .125 .140 3.18 3.56 .360 1.00 1.50 9.14 25.4 38.1 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals.
26、 3. Depth dimension is .29 inch (7.4 mm) for extractors from CAGE 18915 and 5GB68 and .27 inch (6.9 mm) from CAGE 61081. FIGURE 5. Configuration Q dimensions (right hand with bent leg). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 8 Inch
27、es mm Inches mm Inches mm Inches mm Inches mm .003 .005 0.08 0.13 .020 .035 0.51 0.89 .090 .093 2.29 2.36 .125 .140 3.18 3.56 .360 1.00 1.50 9.14 25.4 38.1 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are
28、 .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Depth dimension is .29 inch (7.4 mm) for extractors from CAGE 18915 and 5GB68 and .27 inch (6.9 mm) from CAGE 61081. FIGURE 6. Configuration R dimensions (right hand). Provided by IHSNot for ResaleNo repr
29、oduction or networking permitted without license from IHS-,-,-AA59832/6 9 APPLICATION DATA. Extractor orientation with circuit card assembly printed board. Figures 7 and 8 show the extractor mounted to a circuit card assembly and installed into a locking card guide from different views. Figure 7 dep
30、icts one strait on and two angled views of a right hand extractor fastened to the printed board of a circuit card assembly. Figure 8 depicts a right side view of a circuit card assembly with a right hand extractor fastened to the printed board. FIGURE 7. Extractor fastened to circuit card assembly (
31、right hand extractor shown). FIGURE 8. Circuit card assembly to card guide view (right hand extractor shown). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 10 Circuit card positioning in relation to actuating surface. Two positions of a c
32、ircuit card assembly edge to a locking card guide when seated in the connector are shown on figure 9. The circuit card assembly is ejected from its installed position by lever action of the extractor against the tab on a locking card guide (shown) or actuating surface of a card cage. The extractor w
33、ill allow .030 inch (0.8 mm) over travel for tolerance take-up. Two extractors mounted on each circuit card assembly is recommended. Inches mm Inches mm Inches mm Inches mm .060 1.52 .125 3.18 .250 6.35 .290 7.37 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general inform
34、ation only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 9. Circuit card assembly to card guide dimensions (right hand extractor shown). Provided by IHSNot for ResaleNo reproduction or networking perm
35、itted without license from IHS-,-,-AA59832/6 11 Circuit card assembly printed board. The circuit card assembly should be designed so that electronic components on the printed board in the area around the extractor mounting hole have sufficient clearance for extractor rotation as shown on figure 10.
36、Inches mm Inches mm Inches mm Inches mm Inches mm .094 2.39 .250 6.35 .370 9.40 .42 10.67 .61 15.49 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch
37、 (0.25 mm) for three place decimals. FIGURE 10. Printed board clearance zone and mounting hole dimensions. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents
38、. Commercial Item Description AA59832 Extractor, Electrical Card, Metal, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4
39、D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59832. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification she
40、et preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufactur
41、ers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 12 Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 92121341
42、0 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 URL: 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unli
43、mited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number (P/N) supersession data. This CID specification sheet PINs supersedes the following manufacturers P/Ns as shown in table IV and on DESC Drawing 84191 (table V) a
44、s shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE IV. Commercial part number supersession data. PIN designator AA59832/06 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number
45、1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 K11AR 71T61L1E K21AR 71T62L1E 1119A2LRAE K31AR 71T63L1E 1119A3LRAE K41AR 71T64L1E 1119A4LRAE K51AR 71T65L1E 1119A5LRAE K12AB 711L5E K22AB 712L5E F109LBLKSED 1109A2LBAE K32AB 713L5E F1093LBLKSED 1109A3LBAE K42AB 714L5E F1094LBL
46、KSED 1109A4LBAE K52AB 715L5E 1109A5LBAE K11LG 71T61L4E K21LG 71T62L4E 1119A2LCGE K31LG 71T63L4E 1119A3LCGE K41LG 71T64L4E 1119A4LCGE K51LG 71T65L4E; 1119A5LCGE See note at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/6 13 TAB
47、LE IV. Commercial part number supersession data Continued. PIN designator AA59832/06 Vendor similar designator or type part number 1/ CAGE 18915 Vendor similar designator or type part number 1/ CAGE 61081 Vendor similar designator or type part number 1/ CAGE 5BG68 K12LC 711LCC K22LC 712LCC F109LCLRSED 1109A2LCCE K32LC 713LCC F1093LCLRSED 1109A3LCCE K42LC 714LCC F1094LCLRSED 1109A4LCCE K52LC 715LCC 1109A5LCCE K27PC 71CR2L
