1、 INCH-POUND A-A-59923 6 June 2013 COMMERCIAL ITEM DESCRIPTION BARBED TAPE, HELICAL (WIRE REINFORCED LONG BARB) The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This Commercial Item Description (CID) covers helical barb
2、 tape for barb tape entanglements. These entanglements may serve as a security barrier for warehousing, manufacturing, parking lots, storage and other low level security applications. 2. SALIENT CHARACTERISTICS. 2.1 Material. The helical barbed tape shall be made of material as specified below and s
3、hall be subject to all provisions of this CID: a. Barbed tape Stainless steel per ASTM A240/A240M, Type 430 or galvanized steel per ASTM A653/A653M. b. Core wire Stainless steel per ASTM A580/A580M, 300 Series, minimum tensile strength 140,000 psi or galvanized steel per ASTM A764, Finish 2, Class I
4、I, Type B minimum tensile strength 220,000 psi. 2.2 Design and construction. Helical barbed tape furnished under this CID shall conform to the dimensions and design characteristics as specified herein, in Figure 1 and in Table I. Single coil wire reinforced 18 and 24 inch in diameter are to be fabri
5、cated from 0.025 inch thick AISI 430 stainless steel (SS) or ASTM A653/A653M galvanized steel (GA). Each roll shall consist of 33 coil loops with 4 needle sharp barbs located 4 inch on center along the spiral turns. The barb length shall be 2.250 to 2.600 inch tip to tip. Wire reinforced helical coi
6、ls are to be available in combinations of SS or GA clinched 230 degrees around 0.098 inch diameter SS or GA core wire. Tape material (barb) shall be fabricated from SS or GA and is 1 inch wide prior to forming. FIGURE 1. BARBED TAPE. Comments, suggestions, or questions on this document should be add
7、ressed to Defense Supply Center Philadelphia, ATTN: DSCP-NASA, 700 Robbins Avenue, Philadelphia, PA 19111-5096 or e-mail to dscpg&ispecommentsdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assi
8、st.dla.mil. ASMC N/A FSC 5660 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59923 2 TABLE I. Dash Numbers and Design Characteristics. Dash No. Description Dia. inch Coil Loops Strip Material Core Wire Coil Spacing inch Yield feet Pkg. ASTM F 19
9、10 Item # 1 Helical Single Coil 18 33 SS GA 18 50 5/box #2 2 Helical Single Coil 18 33 GA GA 18 50 5/box #2 3 Helical Single Coil 18 33 SS SS 18 50 5/box #1 4 Helical Single Coil 24 33 SS GA 18 50 5/box #6 5 Helical Single Coil 24 33 GA GA 18 50 5/box #6 6 Helical Single Coil 24 33 SS SS 18 50 5/box
10、 #5 3. REGULATORY REQUIREMENTS. 3.1 The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The products provided sh
11、all meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and the quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of su
12、ch conformance. 5. PACKAGING. 5.1 Preservation, packing and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Unless otherwise specified, all dimensions are in inches. 6.2 Unless otherwise specified in the contract or purchase order, packaging shall be in accordance with ASTM D39
13、51. 6.3 The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractors. The part number identification number (PIN) shall consist of the basic commercial item description number followed by a dash number from Table I. Exa
14、mple: AA59923 - 6 Dash number Basic number 6.4 Source of documents. 6.4.1 FAR. The FAR may be obtained from the Regulatory Secretariat, 1800 F Street NW, Washington DC 20405 or online at http:/www.acqnet.gov. 6.4.2 ASTM Standards. Copies of ASTM standards may be obtained from the ASTM International,
15、 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59923 3 6.5 Ordering data. The contract or order should specify the following: a. CID document number, revis
16、ion, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 6.6 Key words. Coil loops Entanglements Security Barrier MILITARY ACTIVITIES: CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS Custodians: Army AT Preparing activity: Navy YD DLA IS Air Force 99 (Project 5660-2013-001) NOTE:
17、The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
