1、_ ANLOLSOL THRU ANLO2000 REV 3 53 79999L5 0000230 II IECTION L :i3 .500 .562 .625 A88 -750 .812 -875 .938 1.000 1 .O62 1.125 1.188 RU TH A .265 ,328 -390 .452 -515 .578 .640 .702 -765 .E28 .Ego ,952 1.015 1 .O78 - K . o00 . O60 - 13 I3 .125 .i88 .250 .312 .375 .438 .500 .562 .625 - (a) THREAD TO HEA
2、D. .190(NO. 10) -32NF-3A SPEC MIL-S-7742 -THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN .O03 FIR. CHAMFER 30 TO .375 DIA (OPPOSITE SIDE OPTIONAL) 1.250 1.312 1.375 1.438 1.500 1.625 1.750 AN101906 1 .875 AN101907 2.000 (I $g:$ll 2.250 2.125 AN101910 2.375 AN101911 2.500 AN101912 II 2.625 AN101913 2.
3、750 AN101914 2.875 AN101915 I( 3.000 AN101916 3.125 A - 1.140 1.202 1.265 1.328 1 390 1.515 1.640 1.765 1 .ago 2.015 2.140 2.265 2 * 390 2.515 2.640 2.765 2.890 3.015 3.140 3.265 3 390 K + . O00 - .O60 .688 -750 .E12 .a75 .938 i .O62 1. i88 1.312 1.438 1.562 1.688 1.812 1.938 2.062 2.188 2.312 2.438
4、 2.562 2.688 2.812 2.938 MAXIMUM TWO IMPERFECT THREADS. 101920 3.625 101921 3 .no AN101922 3 875 AN101923 AN101924 AN101925 101926 AN101927 AN101928 AN101929 AN 1 O 19 3 O AN101931 AN101932 AN101933 AN101934 AN101935 AN101937 101936 AN101938 AN101939 3.515 3.640 3.765 ANGULAR LOCATION . MAY VARY FRE
5、ELY K +.O00 - .o60 3.062 3, i88 3.312 SHANK SHALL BE STRAIGHT WITHIN ,004 FIR PER INCH OF BOLT LENGTH. THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON PART NO. Ah01941 AN101942 AN1019
6、43 ID D r. IZ 3 C rn - G P e s o -it v M 3 ,-, SHALL BE WITHIN .O11 FIR. MATERIAL: STEEL AY36322 HARDNESS.: ROCKWELL C26-32 FINISH: CADMIUM PLATE AMS2400 SURFACE ROUGHNESS: AS107 ai MANUFACTURING SPECIFICATION: AMS7452 PARTS SUBJECT TO MAGNETIC INSPECTION PER AMS2640. fi b 9 INSPECTION: ALL PARTS SH
7、ALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AM92840. BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. CO DIMENSIONS IN INCHES. DO NOT USE UNASSIGNED PART NUMBERS. ?LESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS f.010, ANGULAR DIMENSIONS 22 . n INACTIVE FOR NEW DESIGN AFTER 3 W
8、CH 1969 NO SUPERSEDING STANDARD. U - THTS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. AIR FORCE-NAVY AERONAUTICAL STANDARD ANIOI 901 ANI O 2000 P.A AF-li THRU CUST. NAVY- AC BOLT - HEX HEAD, DRILLED SHANK, .190-32 ARMY-AV K ! THIS DOCUMENT CONTAINS ) PAGES. 5306-1004 - Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
